Manufacturing Technology 2011, 11(1):32-39 | DOI: 10.21062/ujep/x.2011/a/1213-2489/MT/11/1/32

Alternative machining procedures of hardened steels

Kundrák János
Department of Production Engineering, University of Miskolc 3515 Miskolc-Egyetemváros, Hungary

This paper outlines the hard machining procedures, their applicability, the increase of their efficiency and the possibilities provided through their combination. It focuses on the advantages of the cutting and grinding compared to each other and also on the cases when it is appropriate to apply them or possibly combine them.

Keywords: grinding, hard turning, alternative machining, hardened steel

Published: December 1, 2011  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
János K. Alternative machining procedures of hardened steels. Manufacturing Technology. 2011;11(1):32-39. doi: 10.21062/ujep/x.2011/a/1213-2489/MT/11/1/32.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. Tönshoff, H. K.; Arendt, C.; Ben Amor, R. (2000). Cutting of hardened steel, Annals of the CIRP, Vol.49/2/2000 pp.547-566 Go to original source...
    2. Karpuschewski-Knoche-Hipke: Gear finishing by abrasive processes, CIRP Annals 57 (2008) pp.621-640) Go to original source...
    3. Zębala W.: Simulation of Cutting with the Defined Tool Geometry, Journal of Machine Engineering, Vol.5, Nr 3-4, 2005, pp.109-119
    4. Varga, Gy.: Mechanical Modelling of Dry Machining Processes Production Processes and Systems, a Publication of the University of Miskolc, Vol. 04, Miskolc University Press, 2004, pp.139-149.
    5. Beňo, J.: Selected geometrical problems and relationships in hard machining. In: Archiwum Technologii Maszyn i Automatyzacji. vol. 21, No. 2 (2001), pp.13-21
    6. Kundrak, J; Gyani, K; Bana, V: Roughness of ground and hard-turned surfaces on the basis of 3D parameters International Journal Of Advanced Manufacturing Technology Vol. 38 Iss. 1-2 pp.110-119 Published: 2008 Go to original source...
    7. J. Kundrák; B. Karpuschewski; K. Gyáni et al.: Accuracy of hard turning, Journal Of Materials Processing Technology Volume: 202 Issue: 1-3 (2008) pp.328-338 Go to original source...
    8. Szabó O.: Theory and Practice of Ultraprecisional Turning. Gépgyártás, XLV. 2005. 6-7., pp.60-65
    9. Lukovics, I., Bílek, O.: High Speed Grinding, Proc. on the microCAD'2001 International Computer Science Conference, Section N, Production Engineering and Manufacturing Systems, Miskolc, 18-20 March, 2010, pp.207-212
    10. Kundrak J., V. Bana: When hard turning is recommended in machining of hardened steels. Proc. on the 13th International DAAAM Symposium "Intelligent Manufacturing & Automation: Learning from the Nature", Vienna, Austria, 2002. October 23-26. pp.297-298
    11. Koch, K. F.: Technologie des Hochprazisions-Hartdrehens,Dr-|ng. Dissertation, RWTH Aachen
    12. Tóth T., Kundrák J., Gyáni K.: The material removal rate and the surface rate as two new parameters of qualification for hard turning and grinding, Fifth International Symposium on Tools and Methods of Competitive Engineering (TMCE 2004) Switzerland, Lausanne, 2004. pp.629-639
    13. K. Weinert, G. Johlen: Kombinierte Bearbeitung durch Hartdrehen und Schleifen, IDR Archiv 1/2003
    14. Klocke, Brinksmeier, Wiessert: Capability Profile of Hard Cutting and Grinding Processes, Annals of the CIRP Vol. 54/2 (2005) pp.557-580 Go to original source...
    15. Zębala W.: Modeling of Cutting Process with Cooling. Journal Advances in Manufacturing Science and Technology, Oficyna Wydawnicza Politechniki Rzeszowskiej, Vol. 32, Nr 4, 2008, pp.73-81
    16. Szabó O.: Stochastic Modeling of Abrasive Machining Process. University of Miskolc, microCAD 2006 International Scientific Conference, Section M: Production Engineering and Manufacturing Systems, 2006. Marc. 16-17., pp.157-162
    17. Varga Gy., Nyírő, J: Finite Element Analysis of Metal Cutting Proceedings of the microCAD 2006, International Scientific Conference, Section M, Production Engineering and Manufacturing Systems, Miskolc, Hungary, March 16-17, 2006, pp.219-224
    18. G. Johlen: Kombinierte Bearbeitung von Futterteilen durch Hartdrehen und Schleifen, IDR Archiv 1/2004
    19. Maňková, I. - Beňo, J. - Marková, G.: Contribution to hard turned and ground surfaces microgeometry evaluation. In: Acta Mechanica Slovaca. roč. 12, č. 4-a (2008), pp.85-92 ISSN 1335-2393.

    Return to the content