Manufacturing Technology 2012, 12(1):47-51 | DOI: 10.21062/ujep/x.2012/a/1213-2489/MT/12/1/47

Research into the causes cracking of aluminum alloys of Al - Cu during mechanical machining

Michna Štefan, Náprstková Nataša
Department of Technologies and Material Engineering, Faculty of Production Technology and Management, Jan Evangelista Purkyně University in Ústí nad Labem, Na Okraji 1001, 400 01, Ústí nad Labem, Czech Republic

The aim of the work was carried out research on the causes cracking formed aluminum work pieces in the assortment of rods, which sometimes occur in the mechanical machining (turning, drilling) for alloys of Al-Cu. A typical representative for the machining of aluminum alloys is AlCu4MgMnPb alloy, most of which performs heat treatment for hardening increases the ultimate strength. For the given alloy were carried out qualitative and quantitative fractographic analysis of fracture surfaces after machining in order to determine possible causes cracking of the material and thus his insufficient strength. This paper clearly documented that the fractographic analysis methods can clearly and in the extent required to provide answers to the causes of insufficient strength of the material when cutting. At the same time points out the possible causes of cracks in this alloy in machining and ways for their elimination.

Keywords: AlCu4MgMnPb alloy, hardening, eutektikum, EDX analyses

Published: June 1, 2012  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Michna Š, Náprstková N. Research into the causes cracking of aluminum alloys of Al - Cu during mechanical machining. Manufacturing Technology. 2012;12(1):47-51. doi: 10.21062/ujep/x.2012/a/1213-2489/MT/12/1/47.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. BOLIBRUCHOVA, D., TILLOVA, E. (2005) Zlievarenské zliatiny Al-Si. ZU, Zilina: EDIS - vydavatelstvo ZU. ISBN 80-8070-485-6
    2. JASIONOWSKI, R., PODREZ-RADZISZEWSKA, M., ZÁSADA, D. (2011) Cavitation erosion resistance of the chosen aluminum alloys Manufacturing Technology XI, December 11, p. 22-28, ISSN 1213-2489 Go to original source...
    3. JERSAK, J., REJZEK, M. (2011) Ucinek procesní kapaliny na proces soustruzeni a vybrane parametry integrity povrchu. Strojirenska technologie, vol. XVI, 2/2011, p.17-23. ISBN 1211-4162
    4. KUSMIERCZAK, S. (2009) Analyza vad lakovane vrstvy hlinikoveho profilu, Mezinarodní konference Aluminium Stare Splavy 12.-14.10.2009, Sborník příspěvků na CD,, ISBN 978-7414-156-0
    5. MADL, J., BILIK, O., BUMBÁLEK, B., aj. (2000) Ekologie obrabení. Usti nad Labem : UJEP Usti nad Labem. 98 s. Knihovnicka Strojirenske technologie, ISBN 80-7044-328-6.
    6. MICHNA, S., LUKAC, I., OCENASEK, V., KORENY, R., DRAPALA, J., SCHNEIER, H., MISKUFOVA, A. a kol. (2005) Encyklopedie hliniku. Adin, Presov, ISBN 80-89041-88-4.
    7. MICHNA, S., NOVA, I. (2008). Technologie a zpracování kovových materiálů. Adin, Presov, ISBN 978-80-89244-38-6
    8. MICHNA, S., VOJTECH, D., MAJRICH, P. (2008) Vady vznikající pri vyrobe automobilových pístu a možnosti jejich odstranovani. Strojirenská technologie, XIII, 4/2008, str.15-20. ISBN 1211-4162.
    9. NOVA, I., SOLFRONK, P., NOVAKOVA, I. (2011) Vliv mnozstvi dislokaci na tvaritelnost slitin hliniku. Strojirenska technologie. XVI, 2/2011, str. 28-34, ISSN 1211-4162.
    10. NOVAK, M., HOLESOVSKY, F. (2009) Problems of aluminium alloys grinding. Transactions of the Universities of Košice.. 4/2009. Kosice, ISSN 1355-2334
    11. NOVAK, M., HOLESOVSKY, F. (2011) Inovace technologie brouseni hlinikovych slitin, Strojirenska technologie. XVI, 3/2011, p. 34-39. ISBN1211-4162
    12. NOVAK M., LATTNER M., RUZICKA L., HOLESOVSKY F. (2010). Grinding and surface quality parameters at automotive parts machining, in Manufacturing Technology X. December 2010, 36-38pp, ISSN 1213-2489 Go to original source...
    13. WECK, E., LEISTNER, E. (1983) Metallographische Anleitung zum Farbätzen nach dem Tauchverfahren, 2 díl, DVS Düsseldorf
    14. WEISS, V., STRIHAVKOVA, E. (2011) Optimalizace homogenizacniho zihani slitiny AlCu4MgMn, Strojirenska technologie, vol. XVI, no. 5, p. 42-49, ISSN 1211 - 4162
    15. ASM Handbook, Vol.4, Heat Treating, (1991) ASM International, USA,, ISBN 0-87170-379-3

    Return to the content