Manufacturing Technology 2012, 12(2):102-105 | DOI: 10.21062/ujep/x.2012/a/1213-2489/MT/12/2/102

Effect of the processing materials on the ploughing force values

Andrey Dugin, Alexey Popov
Department of Machining and Assembly Faculty of Mechanical Engineering Technical University of Liberec

In micro cutting it is necessary to control the cutting tool. Monitoring of cutting tools is usually accomplished by measuring cutting forces. In order to improve the accuracy of monitoring it is required to consider the ploughing forces. The ploughing forces substantially depend on the processing materials. This article describes the investigation of the effect of processing materials on the ploughing force values. The extrapolation method on zero cut chip thickness was used to determine the ploughing forces. The experiments were performed by cutting of aluminum alloys, structural steels, bronzes and stainless steels.

Keywords: ploughing force, monitoring, micro cutting

Published: December 1, 2012  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Dugin A, Popov A. Effect of the processing materials on the ploughing force values. Manufacturing Technology. 2012;12(2):102-105. doi: 10.21062/ujep/x.2012/a/1213-2489/MT/12/2/102.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. ALBRECHT, P. (1960). New developments in the theory of the metal cutting processes, Part 1. The ploughing process in metal cutting, ASME J. Eng. Ind., 1960, n.82, p.348-357, ISSN: 0022-0817. Go to original source...
    2. ZOREV, N. (1966). Metal cutting mechanisms, Pergamon Press, Oxford, 1966, p.135-180.
    3. STEVENSON, R. (1998). Measurement of parasitic forces in orthogonal cutting, Int. J. Mach. Tools Manuf., 1998, n.38 p.113-130, ISSN: 0890-6955. Go to original source...
    4. TANSEL, I., ARKAN, T., BAO, W., MAHENDRAKAR, N., SHISLER, B., SMITH, D., MCCOOL, M. (2000). Tool wear estimation in micro-machining. Part I: tool usage-cutting force relationship, International Journal of Machine Tools & Manufacture, 2000, n.40 p.599-608, ISSN: 0890-6955. Go to original source...
    5. CHAE, J., PARK, S., FREIHEIT, T. (2006). Investigation of micro-cutting operations, International Journal of Machine Tools & Manufacture, 2006, n.46 p.313-332, ISSN: 0890-6955. Go to original source...
    6. JEMIELNIAK, K., BOMBINSKI, S., ARISTIMUNO. P. (2008). Tool condition monitoring in micromilling based on hierarchical integration of signal measures, CIRP Annals, 2008, ISSN: 0007-8506. Go to original source...
    7. ŽIŽKA, J., LINHART, T. (2009). Urcovani stavu opotrebenisoustružnickeho nože pomoci pomeru složek rezne sily, Strojirenska technologie, 2009, n. 1, p. 23-28, ISSN 1211-4162.
    8. KASINA, M., VASILKO, K. (2012). Experimental Verification of the Relation between the Surface Roughness and the Type of Used Tool Coating, Manufacturing Technology, 2012, n.12, ISSN 1213-2489. Go to original source...
    9. WYEN, C., WEGENER, K., ZUST, R. (2010). Influence of cutting edge radius on cutting forces in machining titanium, CIRP Annals, 2010, ISSN: 0007-8506. Go to original source...
    10. PŘIKRYL, Z., MUSILKOVA, R. (1975). Teorie obrábění, 1975, p.62 - 77.
    11. POPOV, A., DUGIN, A. (2012). Experimental Methods of Determining the Cutting Forces at the Tool's Rear Surface, Russian Engineering Research, 2012, Vol. 32, n. 1, p. 68-69, ISSN: 1934-8088. Go to original source...
    12. DUGIN, A., POPOV, A. (2012). Effect of the cutting tool wear on the ploughing force values, Strojírenská Technologie, 2012, n. 17, p. 19-23, ISSN 1211-4162.

    Return to the content