Manufacturing Technology 2012, 12(2):136-140 | DOI: 10.21062/ujep/x.2012/a/1213-2489/MT/12/2/136

The effect of chlorhexidine on the colour and tint change of ceramic dental veneer

Dorota Klimecka-Tatar, Stanisław Borkowski
Czestochowa University of Technology, Faculty of Management, Institute of Engineering Production, Armii Krajowej 19b, 42-200, Częstochowa

Frequent consumption of certain products contained the different kinds of chemical compounds affects on the colour of teeth, especially on prosthetic restoration timbre. A very interesting issue is to determine the effect of exposure in some of the commonly used chemical substances on dental restorations colour change. The study was conducted on the upper crown of the tooth, namely the first incisor. The colour evaluation change has been made using a spectrophotometer SpectroShade, which determines the amount of light absorbed by the element over the entire visible spectrum 380 - 720 nm. In the paper was shown that long-term use of products that contain chlorhexidine can lead to permanent color change of ceramics dental materials. After long exposure in the solution the ceramic became lighter but their hue value indicates that the color is closer to yellow.

Keywords: dental veneer, colour change, spectrophotometer, dental restoration

Published: December 1, 2012  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Klimecka-Tatar D, Borkowski S. The effect of chlorhexidine on the colour and tint change of ceramic dental veneer. Manufacturing Technology. 2012;12(2):136-140. doi: 10.21062/ujep/x.2012/a/1213-2489/MT/12/2/136.
Download citation

References

  1. HATTAB F.N., QUDEIMAT M.A., AL-RIMAWI H.S. (1999) Dental discoloration: an overview, Journal of Esthetic Dentistry pp. 11-13. Go to original source...
  2. JOINER A. (2004) Tooth colour: a review of the literature, Journal of Dentistry. Vol. 32, pp. 3-12. Go to original source...
  3. TERRY D.A., GELLER W., TRIC O., ANDERSON M.J., TOURVILLE M., KOBASHIGAWA A. (2002) Anatomical form defines color: function, form and aesthetics, Practical Procedures and AestheticDentistry Vol. 14, pp. 9-67.
  4. JOINER A., JONES N.M., RAVEN S.J. (1995) Investigation of factorsinfluencing stain formation utilizing an in situ model, Advances in Dental Research, Vol. 9, pp. 471-476. Go to original source...
  5. MACPHERSON L.M.D., STEPHEN K.W., JOINER A., SCHAFER F., HUNTINGTON E. (2000) Comparison of a conventional and modified tooth stain index, Journal of Clinical Periodontology Vol. 27, pp. 854-859. Go to original source...
  6. PRIEST G., LINDKE L. (2000) Tooth color selection and characterisation accomplished with optical mapping, Practical Periodontics and Aesthetic Dentistry, Vol. 12, pp. 497-503.
  7. HAMMAD I.A. (2003) Intrarater repeatability of shade selections with two shade guides, Journal of Prosthetic Dentistry Vol. 89, pp. 50-53. Go to original source...
  8. KHAN A.S., WONG F.S.L., MCKAY I.J., WHILEY R.A., REHMAN I.U. (2013) Structural, mechanical, and biocompatibility analyses of a novel dental restorative nanocomposite Journal of Applied Polymer Science 127 (1), pp. 439-447. Go to original source...
  9. KAYA G. (2013) Production and characterization of self-colored dental zirconia blocks Ceramics International 39 (1), pp. 511-517. Go to original source...
  10. ÇELEN, S., ÖZDEN, H. (2012) Laser-induced novel patterns: As smart strain actuators for new-age dental implant surfaces Applied Surface Science 263, pp. 579-585.
  11. YI W., HU X., ICHIM P., SUN X. (2012) Processing and properties of pressable ceramic with non-uniform reinforcement for selective-toughening Materials Science and Engineering A 558, pp. 543-549. Go to original source...
  12. KLIMECKA-TATAR D., BALA H., SLUSAREK B., JAGIELSKA-WIADEREK K. (2009) The effect of consolidation method on elctrochemical corrosion of polymer bonded Nd-Fe-B type magnetic material, Archives of Metallurgy and Materials, Vol. 54, Issue 1, pp. 247-256.
  13. BÍLEK O., ROKYTA L., ©IMONÍK J. (2012) CAM in the Production of Casting Patterns Manufacturing Technology, Vol. 12, pp. 7-12. Go to original source...