Manufacturing Technology 2013, 13(1):36-39 | DOI: 10.21062/ujep/x.2013/a/1213-2489/MT/13/1/36

Influence of returning material on porosity of die castings

Ľubomír Eperješi, Jozef Malik, Štefan Eperješi, Daniel Fecko
Technicla University of Kosice

With increasing tendency of die castings production, also the possibility to produce castings with maximum usage of molten metal grows. Residual of non-used molten metal, e.g. sprues, feeders, splashes and saw-dusts are used in next production as returning material. With returning material a lot of non-suitable elements is brought into the melting process, but with decreasing of input costs it creates inseparable part of production process. Usage of returning material in melt production has negative influence on final quality of produced castings, because of bringing of inheritable properties into produced melt. Important factor in melt production with the amount of returning material is to know to set its optimal amount and the way of melt treatment to achieve the same results in casting quality in comparison to the casting production from clean materials.

Keywords: returning material, porosity, die casting, casting

Published: March 1, 2013  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Eperješi Ľ, Malik J, Eperješi Š, Fecko D. Influence of returning material on porosity of die castings. Manufacturing Technology. 2013;13(1):36-39. doi: 10.21062/ujep/x.2013/a/1213-2489/MT/13/1/36.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. MALIK, J. (2008). Technology of pressure die casting of aluminium alloys, Inaugural dissertation, Košice.
    2. ĽONC, D. (2008). Suggest a process for using recycled material from aluminum alloys for die casting technology, diploma thesis, Košice.
    3. MALIK, J., FUTÁŠ, P., VASKOVÁ, I. (2009). Recycled material in die casting technology, Slévarenství, březen - april.
    4. RAGAN, E., PAVEL, J., FEDÁK, M. (2008). Trvanlivosť foriem a ďalších častí strojov pre liatie pod tlakom vzhľadom na styk s kvapalným kovom, Nové smery vo výrobných technológiach, Prešov, jún 2008.
    5. BOLIBRUCHOVÁ, D., KANTORÍK, R., PASTIRČÁKOVÁ, M. (2008). Chyby hliníkových odliatkov odlievaných metódou vysokotlakového odlievania, Slévárenství, 2008, pp. 9-10.
    6. GAŠPÁR, Š.; PAŠKO, J.; MALIK, J.; PANDA, A.; JURKO, J.; MAŠČENIK, J. (2012). Dependence of Pressure Die Casting Quality on Die Casting Plunger Velocity Inside a Filling Chamber of a Pressure Die Casting Machine, Advanced Science Letters. Vol. 14, no. 1. Go to original source...
    7. GAŠPÁR, Š.; MAŠČENIK, J. (2011). Kvalitatívne vlastnosti tlakových odliatkov určených pre automobilový priemysel v závislosti na zmene dotlaku; Automobil Industry. Vol. 7, no. 2., p. 18-21.
    8. TUREKOVÁ,I.;KURACINA,R.;BALOG,K.;MARTINKA,J.: (2012). Technologické a prírodné havárie. - 1. vyd. - Trnava : AlumniPress, 2012, 232 s. - e-skriptá. - ISBN 978-80-8096-154-1.
    9. GAŠPÁR, Š.; PAŠKO, J.; KULIK, V. (2012). Analysis of increased pressure effect on internal homogeneity of pressure die castings, Kvalita a spoľahlivosť technických systémov: zborník vedeckých prác : 22. - 23.5.2012, Nitra. - Nitra: SPU, 2012 S. 129-133. - ISBN 978-80-552-0798-8.
    10. GONOS, J. (2009). Analýza dlhodobej likvidity podniku; 2009. In: Acta Montanistica Slovaca. Roč. 14, č. 1 (2009), s.82-85. - ISSN 1335-1788.
    11. TILLOVÁ E., CHALUPOVÁ M., HURTALOVÁ L., ĎURINÍKOVÁ E. (2011). Quality control of microstructure in recycled Al-Si cast alloys; In: Manufacturing Technology, December 11, 70-76, ISSN: 1213-2489. Go to original source...
    12. PAŠKO J. (2010). Die Casting Plunger Pressing Velocity and Analysis of Its Influence on a Permanent Deformation Value of a Casting Made from an EN AC 47100 Alloy; In: Manufacturing Technology, December 10, 23-26, ISSN: 1213-2489. Go to original source...

    Return to the content