Manufacturing Technology 2014, 14(2):234-238 | DOI: 10.21062/ujep/x.2014/a/1213-2489/MT/14/2/234
Advantages of Express-Methods in Investigation of Mechanical and Physical Properties of Aluminum Alloys
- 1 CTU in Prague, Department of Materials Engineering, Karlovo nam. 13, 121 35, Prague 2, Czech Republic
- 2 Polytech Nantes, Department of Materials Engineering, 1, quai de Tourville BP 13522, 44035 Nantes Cedex 1
The investigation of mechanical properties of aluminum alloys by using express-methods is discussed in the present paper. Such properties are hardness, elastic modulus E and yield strength Rp0.2. Tensile test with extensometer and automated ball indentation test (ABI) with 5 mm ball indenter performed in order to obtain the correlations for the basic mechanical properties of aluminum alloys. The results of newly developed method of revealing the microstructure, which involves plastic deformation, show its potential of applicability in engineering practice when measuring the microstructural and submicrostructural features.
Keywords: Automated ball indentation, tensile test, submicrostructure, grain size, EBSD
Published: June 1, 2014 Show citation
| ACS | AIP | APA | ASA | Harvard | Chicago | IEEE | ISO690 | MLA | NLM | Turabian | Vancouver |
Puchnin M, Anisimov E, Cejp J, Kunka I, Vicens S. Advantages of Express-Methods in Investigation of Mechanical and Physical Properties of Aluminum Alloys. Manufacturing Technology. 2014;14(2):234-238. doi: 10.21062/ujep/x.2014/a/1213-2489/MT/14/2/234.
References
- MICHNA, İ., LUKÁÈ, I., LOUDA, P., et all. (2007). Aluminum materials and technologies from A to Z. 630 p. ISBN 978-80-89244-18-8. Adin Co.
- MICHNA, S., NÁPRSTKOVÁ, N. (2012). Research into the causes cracking of aluminum alloys of Al - Cu during mechanical machining, Manufacturing Technology Vol. 12, Issue 12, pp. 47-51.
Go to original source... - BRÙNA M., KUCHARÈÍK L. (2013). Prediction of the Porosity of Al Alloys, Manufacturing Technology Vol. 13, Issue 3, pp. 296-302. Go to original source...
- MATJUNIN V. M. (2008). Metallovedenie v teplojenergetike, 328 p. Moskva, Izdatel'skij dom MPEI.
- GOST 22762-77, Metally i splavy: metod izmerenija tverdosti na predele tekuchesti, Gosudarstvennyj komitet standartov soveta ministrov SSSR, Moskva.
- GOST 18835-73, Metally: Metod izmerenija plasticheskoj tverdosti, Gosudarstvennyj komitet standartov soveta ministrov SSSR, Moskva.
- ASTM WK381, Standard Test Methods for Automated Ball Indentation Testing of Metallic Samples and Structures to Determine Stress-Strain Curves and Ductility at Various Test Temperatures.
- MATJUNIN V. M. (2006). Operativnaja diagnostika mehanicheskih svojstv konstrukcionnyh materialov: posobie dlja nauchnyh i inzhenerno-tehnicheskih rabotnikov. 216 p.. Moskva, Izdatel'skij dom MPEI
- HILL R, STORAKERS B, ZDUNEK A. B. (1989). A theoretical study of the Brinell hardness test. Vol.423, pp. 301-330. Proceedings of the Royal Society of London. Go to original source...
- BIWA S, STORAKERS B. (1995). An analysis of fully plastic Brinell indentation. Vol.43, pp. 1303-1333. Journal of Mechanics and Physics of Solids. Go to original source...
- BRINELL I A. (1900). II Congress Int. Des Methodes d'essai, Paris.
- ANISIMOV, Evgeniy, PUCHNIN, Maxim. (2014). Reduction of Elastic Modulus of Titanium Alloy Ti-6Al-4V by Quenching. Key Engineering Materials, Vol. 586, pp.15-18. Trans Tech Publications, Switzerland. doi:10.4028/www.scientific.net/KEM.586.15. Go to original source...
- HURLEY P.J., HUMPHREYS F.J. (2003). The application of EBSD to the study of substructural development in a cold rolled single-phase aluminium alloy. Vol. 51, Issue 4, 2003, pp. 1087-1102. Acta Materialia. Go to original source...
- TREĞJАKOV, A.; TROFIMOV, G.; GUR'JАNOVA, M. (1971). Mehanicheskie svoistva stalej i splavov pri plasticheskom deformirovanii, 64 p. UDK 621.7.011. Moskva "Mashinostroenie".