Manufacturing Technology 2014, 14(3):467-470 | DOI: 10.21062/ujep/x.2014/a/1213-2489/MT/14/3/467

Change of Internal Friction on Aluminium Alloy with 10.1 % Mg Dependence on the Temperature

Milan Uhríčik1, Peter Palček1, Andrea Soviarová1, Przemysław Snopiński2
1 Department of Material Engineering, Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia
2 Institute of Engineering Materials and Biomaterials, Silesian University of Technology, KonarskiegoSt. 18a, 44-100 Gliwice, Poland

The article is focused on the analysis changes dependence on the temperature on the aluminium alloy with 10.1% Mg, 1.32% Si and 0.43% Mn by internal friction. Internal friction is a property of the material is measured on the ultrasonic resonant aparature at a frequency about f = 20470 Hz. The measured temperature range was from 50 °C up to 420 °C. Precisely measurement of the internal friction can be monitored ongoing structural changes and various mechanisms that prevent these changes.

Keywords: Internal Friction, Aluminium Alloy, Resonant Frequency, Temperature

Published: October 1, 2014  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Uhríčik M, Palček P, Soviarová A, Snopiński P. Change of Internal Friction on Aluminium Alloy with 10.1 % Mg Dependence on the Temperature. Manufacturing Technology. 2014;14(3):467-470. doi: 10.21062/ujep/x.2014/a/1213-2489/MT/14/3/467.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. www.aalco.co.uk
    2. HURTALOVÁ, L., TILLOVÁ, E., CHALUPOVÁ, M. (2014).The changes of fatigue properties in aluminium alloy during solution treatment,pp.433-436.Key engineering materials, ISSN 1013-9826. Go to original source...
    3. HURTALOVÁ, L., TILLOVÁ, E. (2013). Elimination of the negative effect of FE-rich intermetallic phases in secondary (recycled) aluminium cast alloy, pp.44-50. Manufacturing Technology, Vol.13, Num.1, ISSN 1213-2489. Go to original source...
    4. BLANTER, M. (2007). Internal Friction in Metallic Materials, pp.539, Springer - Verlag: Berlin Heidelberg. ISBN 3-540-68757-2
    5. PUŠKÁR, A.(1995). Vnútorné tlmenie materiálov, pp.382, Žilina: EDIS, ISBN 80-7100-260-7.
    6. SOVIAROVÁ, A., DRESSLEROVÁ, Z., PALČEK, P., CHALUPOVÁ, M.(2013). Influence of precipitation on internal damping of AZ61 alloy. 30th international colloquium: Visegrád, Hungary - Budapešť, 22-24 May 2013, pp.153-158. ISBN 978-963-313-079-7.
    7. HLAVÁČOVÁ, I., PALČEK, P., CHALUPOVÁ, M., DRESSLEROVÁ, Z. (2013). Plastic deformation properties of Magnesium alloy AZ61, pp.313-319. Manufacturing Technology, Vol.13, Num.3, ISSN 1213-2489. Go to original source...
    8. SOVIAROVÁ, A., PALČEK, P., BLAŽEK, D.(2013), Analysis of Spurious Effects on Ultrasonic Internal Damping Testing Equipment, In TRANSCOM 2013 10th EUROPEAN CONFERENCE OF YOUNG RESEARCHES AND SCIENTISTS.
    9. PORUBČAN, J., PALČEK, P., BLAŽEK, D., TROJANOVÁ, Z. (2012). Internal friction in extruded aluminium alloy, pp.197-202. Solid State Phenomena: Internal friction and mechanical spectroscopy. Vol. 184, ISSN 1012-0394 Go to original source...
    10. KASENČÁK, M. (2010). Vnútorné tlmenie zliatin horčíka v závislosti od amplitúdy deformácie: Dizertačná práca, Žilina: Žilinská Univerzita v Žiline, 97 p.
    11. NAMAŠNÝ, A. (2008). Štúdium vlastností horčíkových zliatin meraním vnútorného tlmenia: Dizertačná práca, Žilina: Žilinská Univerzita v Žiline, 90 p.

    Return to the content