Manufacturing Technology 2015, 15(3):322-329 | DOI: 10.21062/ujep/x.2015/a/1213-2489/MT/15/3/322

Experimental Investigation and Analysis of Cutting Forces When Machining X5CrNi18-10 Stainless Steel

Rozmarina Dubovska, Jozef Majerik
Faculty of Education, University of Hradec Kralove. Rokitanskeho 62, 500 03 Hradec Kralove. Czech Republic

In this study, cutting forces experimental measurement an analysis with special carbide insert when turning austenitic stainless steel have been investigated. Stainless steel X5CrNi18-10 is often considered as poorly machinable material. In this experimental study a number of turning tests carried out by using a test lathe and a cutting force measuring device are presented. Accordingly the effect of cutting speed and tool insert cutting geometry on cutting forces in turning austenitic stainless steel X5CrNi18-10 (AISI 304) using Wiper cemented carbide tool insert has been discussed. The effect of cutting parameters (feed rate, depth of cut) is also analyzed by cutting forces measurement. The input parameters were varied as vc = 100 m.min-1, f = 0,150 and 0,275 mm and edge geometry r = 95°, r'= 5°, εr = 80°, rε = 0, 8 mm, s = -6°. The results show that main cutting force Fc decreases with the increasing of cutting speed in turning without using the coolant. A benefit for production process also confirmed fact that this growth is 2,5 to 3 times higher as for turning of CS0E4 under the same machining conditions due to the hardening of austenitic steels for chip creation. It was also noted that experimental specimens showing larger cutting forces then generated worse surface finish as well as larger surface damage.

Keywords: Austenitic stainless steel, Cutting forces, Cutting parameters, KISTLER measuring device

Published: June 1, 2015  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Dubovska R, Majerik J. Experimental Investigation and Analysis of Cutting Forces When Machining X5CrNi18-10 Stainless Steel. Manufacturing Technology. 2015;15(3):322-329. doi: 10.21062/ujep/x.2015/a/1213-2489/MT/15/3/322.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. FANG, N., SRINIVASA PAI, P., EDWARDS, N. (2013). A comparative study of high-speed machining of Ti-Al-4V and Inconel 718 - part I: effect of dynamic tool edge wear on cutting forces. In: Int. Jour. Adv. Manuf. Techn., Vol. 68, pp. 1839-1849. Springer. Go to original source...
    2. CZARNOTA, CH., KONÉ, F., HADDAG, B., NOUARI, M. (2015). A predictive hybrid force modeling in turning: application to stainless steel dry machining with a coated groove tool. In: Int. Jour. Adv. Manuf. Techn., Article in press. Springer. Go to original source...
    3. AKYILDIZ, H. K. (2013). Evaluating of cutting forces in thread machining. In: Int. Jour. Adv. Manuf. Techn., Vol. 68, pp. 1601-1612. Springer. Go to original source...
    4. FERNÁNDEZ-ABIA, A. I., BARREIRO, J, LÓPEZ DE LACALLE, L. N., MARTÍNEZ-PELLITERO, S. (2012). Behavior of austenitic stainless steels at high speed turning using specific force coefficients. In: Int. Jour. Adv. Manuf. Techn., Vol. 62, pp. 505-515. Springer. Go to original source...
    5. QIAN, L., HOSSAN, M. R. (2007). Effect on cutting force in turning hardened tool steels with cubic boron nitride inserts. In: Journal of Materials Processing Technology, Vol. 191, pp. 274-278. Elsevier BV. Go to original source...
    6. WANG, J. (2000). The effect of the multi-layer surface coating of carbide inserts on the cutting forces in turning operations. In: Journal of Materials Processing Technology, Vol. 97, pp. 114-119. Elsevier BV. Go to original source...
    7. KULKARNI, A. P., JOSHI, G. G., SARGADE, V. G. (2013). Dry turning of AISI 304 austenitic stainless steel using AlTiCrN coated insert produced by HPPMS technique. In: Procedia Engineering, Vol. 64, pp. 737-746. Elsevier BV. Go to original source...
    8. MADAJ, M., PISKA, M. (2013). On the SPH Orthogonal Cutting Simulation of A2024-T351 Alloy. In: Procedia CIRP, Vol. 8, pp. 152-157. Elsevier BV. Go to original source...
    9. XINFENG, H., SU, W., KRATZ, H. (2006). Forces in Hard Turning of 51CrV4 with Wiper Cutting Tool. In: Tsinghua Science and Technology, Vol. 11, pp. 501-506. Go to original source...
    10. DUBOVSKA, R., MAJERIK, J., CHOCHLIKOVA, H. (2014). Cutting forces numerical analysis and research in dry turning of 1.4301 with wiper coated carbide insert. In: Applied Mechanics and Materials, Vol. 528, pp. 34-43. TTP Switzerland. Go to original source...
    11. KLOCKE, F., GESCHWILLER, K. (2009). Size effect of micro drilling in steel. In: Production Engineering, Vol. 3, pp. 69-72. Springer. Go to original source...
    12. KIENZLE, O., VICTOR, H. (1957). Spezifische Schnittkrafte bei der Metallbearbeitung. In: Werkstoff technik und Machinenbau, Vol. 47, pp. 224-225.
    13. GUNAY, M., SEKER, U., SUR, G. (2006). Design and construction of a dynamometer to evaluate the influence of cutting tool rake angle on cutting forces. In: Materials & Design, Vol. 27, pp. 1097-1101. Go to original source...
    14. YIALDIZ, S, ÛNSACAR, F. (2006). A dynamometer design for measurement the cutting forces on turning. In: Measurement, Vol. 39, pp. 80-89. Elsevier. Go to original source...
    15. Kistler Instrument Corp, High resolutions measurement of force, torque and strains, US, 2004.
    16. PARO, J., HÄNNINEN, H., KAUPINNEN, V. (2001). Tool wear and machinability of X5CrMn18 stainless steel. In: Journal of Materials Processing Technology, Vol. 119, pp. 14-20. Elsevier BV. Go to original source...
    17. MRKVICA, I., NESLU©AN, M., KONDERLA, R., JURKO, J., PANDA, A. (2013). Cutting forces by turning of incInconel 718 with inserts from different materials. In: Manufacturing Technology, Vol. 13, pp. 499-504. Go to original source...
    18. WAGH, S. S., KULKARNI, A. P., SARGADE, V. G. (2013). Machinability studies of austenitic stainless steel (AISI 304) using PVD cathodic arc evaporation (CAE) system deposited AlCrN/TiAlN coated carbide inserts. In: Procedia Engineering, Vol. 64, pp. 907-914. Elsevier BV. Go to original source...
    19. ÈEP, R., JANÁSEK, A., SLIVA, A., NESLU©AN, M., BINDER, M. (2013). Experimental tool life tests of indexable inserts for stainless steel machining. In: Tehnicki Vjesnik, Vol. 20, pp. 933-940.
    20. FERNÁNDEZ-ABIA, A. I., BARREIRO, J, LÓPEZ DE LACALLE, L. N., MARTÍNEZ, S. (2011). Effect of very high cutting speeds on shearing, cutting forces and roughness in dry turning of austenitic stainless steels. In: Int. Jour. Adv. Manuf. Techn., Vol. 57, pp. 61-71. Springer. Go to original source...

    Return to the content