Manufacturing Technology 2015, 15(3):380-384 | DOI: 10.21062/ujep/x.2015/a/1213-2489/MT/15/3/380

Cutting Tool Wear Monitoring

Jan Madl, Michal Martinovsky
Faculty of Production Technology and Management, J. E. Purkyne University in Usti nad Labem, Pasteurova 3334/7, 400 01, Usti nad Labem, Czech Republic

Cutting tool wear monitoring is one of key problems in automation of machining processes. Apart from the cutting tool wear monitoring for the cutting tool change and cutting tool failure, cutting tool wear monitoring may be one of the components for the adaptive control of a machining process. This paper is focused on the design of turning cutting tool wear sensors of the system flap - jet principal with increased extend. On the geometric principles in cutting with a turning cutting tool, the relations among the output of jet mouth, clearance angle and cutting tool wear were expressed. Two variants of turning cutting tool sensors were designed and experimentally verified. The results of experiments have proved the possibility to apply cutting tool wear sensor of the system flap - jet principal with increased extend in practical use.

Keywords: Machining, Cutting tool wear, Monitoring

Published: June 1, 2015  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Madl J, Martinovsky M. Cutting Tool Wear Monitoring. Manufacturing Technology. 2015;15(3):380-384. doi: 10.21062/ujep/x.2015/a/1213-2489/MT/15/3/380.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. MARK, A. (2000). Insert has built-in wear sensor. Modern Machine Shop. Vol. 73, No. 5, p. 1.
    2. CAROLAN, T. A., KIDD, S. R., HAND, D. P., WILCOX, S. et al. (1997). Acoustic emission monitoring of tool wear during the face milling of steels and aluminium alloys using a fiber optic sensor. Proceedings of the Institution of Mechanical Engineers. Vol. 211, No. 4, p. 11. Go to original source...
    3. ZIZKA, J. (2003). Pouziti akusticke emise ke sledovani stavu rezneho nastroje. Liberec: TU Liberec. p. 106. ISBN 80-7083-687-1.
    4. GOMES DE OLIVEIRA, J. F., DORNFELD, D. A., Winter, B. (1994). Dimensional Characterisation of Grinding Wheel Surface through Acoustic Emission. Annals of the CIRP. Vol. 1, p. 291. Go to original source...
    5. KOCMAN, K., PROKOP, J. (2001). Prediction of Grinding Wheel Parameters. Manufacturing Technology. Vol. 1, No. 1, pp. 26-32.
    6. TONSHOFF, T., FREIMUTH, J. C., BECKER, R. (2002). Process Monitoring in Grinding. Annals of the CIRP. Vol. 2, pp. 551-671. Go to original source...
    7. SHIBATA, J., GOTO, T., YAMAMOTO, M., TSUWA, H. (1982). Characteristics of Air Flow Around a Grinding Wheel and their Availability for Assessing the Wheel Wear. Annals of the CIRP. Vol. 1, p. 233. Go to original source...
    8. BRINKSMEIER, F. (1992). Monitoring of Grinding Wheel Wear. Annals of the CIRP. Vol. 1, p. 373. Go to original source...
    9. BI, X. F., YANG, C. Sc. (2013). Research on Crater Wear Monitoring. Applied Mechanics and Materials. Vol. 436-442, pp. 2390-2393. Go to original source...
    10. DIEI, E. N., DORNFELD, D. A. (1987). Acoustic emission from the face milling process-the effects of process variables. Trans. ASME. Vol. 109, pp. 234-240. Go to original source...
    11. MADL, J. Tool Wear and Breakage Monitoring in Machining (1992). VDI Berichte, Nr. 94, pp. 274-250.
    12. GIUST, D., SANTOCH, M., TANTUSSI, G. (1987). On Line Sensing of Flank Wear and Crater Wear of Cutting Tools. Annals of the CIRP. Vol. 1, p. 41. Go to original source...
    13. HRABOVSKY, T., NesluSan, M., MiCieta, B., CillikovA, M., MiCietovAl, A. (2014). Berkhausen Noise Emission of Surfaces Produced by Hard Milling Process. Manufacturing Technology. Vol. 14, No. 1. Go to original source...
    14. MICUCH, M., CILLIKOVA, M., NESLUSAN, M., MICETOVA, A. (2014). Influence of Cutting Conditions and Grinding Wheel Wear on Bergausen Noise of Ground Surfaces. Manufacturing Technology. Vol. 14, No.1. Go to original source...
    15. CASENSKY, M. (1970). Meridlo s rozsirenym rozsahem. Prague: CVUT in Prague, K235, CTU. [Research Report].
    16. NGUYEN, V. G. (1975). Vysokotlaka pneumaticka meridla. Prague: CVUT. Doctoral thesis. CVUT in Prague, K234, CTU.

    Return to the content