Manufacturing Technology 2015, 15(3):462-468 | DOI: 10.21062/ujep/x.2015/a/1213-2489/MT/15/3/462

Barkhausen Noise Emission of Surfaces after Laser Beam Machining

Alena Vajdova, Anna Micietova, Maria Cillikova, Miroslav Neslusan
University of Žilina, Faculty of Mechanical Engineering, Univerzitná 1, 010 26 Žilina, Slovak republic

This paper deals with analysis of surface integrity of steel after laser beam machining (LBM). The paper discusses surface integrity expressed in term of rms values of Barkhausen noise and reports about variables affecting Barkhausen noise emission such as laser power, gas pressure, thickness of machined surface, focus distance and feed speed. The paper demonstrates variable degree of surface hardening due to elevated temperatures and the following rapid cooling. Except magnetic investigation of surface also stress state and structure observation are reported. This study demonstrates that thickness samples takes major role from the point of surface integrity expressed in structure transformations as well as stress state whereas influence of focus distance and gas pressure are only minor. Medium degree of surface integrity transformation can be driven by variation of laser power and feed speed.

Keywords: laser beam machining, Barkhausen noise, surface hardening

Published: June 1, 2015  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Vajdova A, Micietova A, Cillikova M, Neslusan M. Barkhausen Noise Emission of Surfaces after Laser Beam Machining. Manufacturing Technology. 2015;15(3):462-468. doi: 10.21062/ujep/x.2015/a/1213-2489/MT/15/3/462.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. MIČIETOVÁ, A. (2007) Nekonvenčné metódy obrábania - výber, využitie, perspektívy, EDIS Žilina, ISBN 978-80-8070-775-0.
    2. MIČIETOVÁ, A., MAŇKOVÁ, I., VELÍŠEK, K. (2007). Top trendy v obrábaní, V. časť - Fyzikálne technológie obrábania, MEDIA/ST, s.r.o., Žilina, ISBN 80-968954-7-2.
    3. MAŇKOVÁ, I. (2000). Progresívne technológie, Vienala, Košice.
    4. PARANDOUSH, P., HOSSAIN, A. (2014). A review of modeling and simulation of LBM, In: International Journal of Machine Tools and Manufacture, Vol. 85, pp. 135-145. Go to original source...
    5. MEIJER, J. (2004). Laser beam machining (LBM), state of the art and new opportunities, In: Journal of Material Processing Technology, Vol. 149, pp. 2-17. Go to original source...
    6. MIČIETOVÁ, A., NESLUŠAN, M., ČILLIKOVÁ, M. (2013). Influence of surface geometry and structure after non-conventional methods of parting on the following milling operation, In: Manufacturing technology, Vol.13, pp. 199-204. Go to original source...
    7. MIČIETOVÁ, A., NESLUŠAN, M., ČILLIKOVÁ, M. (2013). Residual stresses after thermal methods parting, In: Machines Technologies Materials, Vol. 2, pp. 235 - 240.
    8. VAJDOVÁ, A. el all. (2014). Analysis of surface integrity of parts after non conventional methods of machining, In: Manufacturing technology, Vol.14, pp. 470-474 Go to original source...
    9. KAMEDA, J., RANJAN, R. (1987). Nondestructive evaluation of steels using acoustic and magnetic Barkhausen signals - II. Effect of inter granular impurity segregation, In: Acta Metall., Vol. 35/7, 1987, pp. 1527-1531. Go to original source...
    10. BUTTLE, D.J., et all. (1991). Magneto-acoustic and Barkhausen emission: their dependence on dislocations in iron, In: NDT & E Int., Vol. 24, pp.47 - 54. Go to original source...
    11. GATELIER-ROTHEA, C., et all. (1998). Characterization of pure iron and carbon-iron binary alloy by Barkhausen noise measurements: study of the influence of stress and microstructure, In: Acta Mater. Vol. 46/14, 1998, pp.4873-4882. Go to original source...
    12. RANJAN, R., JILES, C., RASTOGI, P. (1987). Magnetic properties of decarburized steels: An investigation of the effects of grain size and carbon content, In: IEEE Trans. Magn., Vol. 23/3, 1987, pp.1869-1876. Go to original source...
    13. DURSTOVÁ, Z. et all. (2014). Non-destructive evaluation of ground surfaces made of bearing steel of variable hardness, In: Manufacturing technology, Vol.14, 2014, pp. 297-303. Go to original source...
    14. ČILLIKOVÁ, M. et all. (2014). Detection of surface damage after grinding of large case-hardened bearing rings, In: Engineering materials, Vol. 581, pp. 205-210. Go to original source...
    15. BLAOW, M., EVANS, J., SHAW, B. (2005). Magnetic Barkhausen noise: the influence of microstructure and deformation in bending, In: Acta Materialia, Vol. 53, pp.279-287. Go to original source...
    16. MOORTHY, V. et all. (2001). Evaluation of heat treatment and deformation induced changes in material properties in gear steels using magnetic Barkhausen noise analysis, ICBN 03 Tampere, Finland.
    17. MIČIETOVÁ, A., NESLUŠAN, M., ČILLIKOVÁ, M. (2013). Influence of surface geometry and structure after non-conventional methods of parting on the following milling operations, In: Manufacturing technology, Vol.13, pp. 199-204. Go to original source...
    18. BREZANI, J. (2012). Model vzájomných relácií pri termickom rezaní materiálov, PhD. Thesis, University of Žilina
    19. MIČIETA, B., BIŇASOVÁ, V., HALUŠKA, M. (2014). Reconfigurable manufacturing system and sustainable production, 1. vyd. - Saarbrücken : LAP LAMBERT Academic Publishing, 86 s. ISBN 978-3-659-59101-3
    20. MEŠKO, J. et all. (2014). Microstructure analysis of welded joints efter laser welding, In: Manufacturing technology, Vol.14, pp. 355-359 Go to original source...

    Return to the content