Manufacturing Technology 2015, 15(5):845-850 | DOI: 10.21062/ujep/x.2015/a/1213-2489/MT/15/5/845

The Using of Vehicle Moving Simulation to Proposal of Construction Work

Milan Chalupa
Faculty of Military Technogy, University of defence, Kounicova 65, 662 10 Brno

The article describes main possible usage of results of dynamic loading simulation with using of computational simulating system MSC. ADAMS. AVT and simulating computational model of track vehicle undercarriage. Main contens of article is the descripton of using of results for design value make-up file of changes of vehicle chassis parts and its new operating settings. The second described possibility of results simulation calculations usage is making - up of aproximate relations for transaction of fast orientation calculations. The next possibility of usage of simulation results is the possibility to verificate of mathematic model. The optimalization of influence changes of several design value together is last mentioned possibility of usage of simulation calculations results in the contens of this article.

Keywords: computation modeling, simulation

Published: November 1, 2015  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Chalupa M. The Using of Vehicle Moving Simulation to Proposal of Construction Work. Manufacturing Technology. 2015;15(5):845-850. doi: 10.21062/ujep/x.2015/a/1213-2489/MT/15/5/845.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. BARTÁK, J., KRÓNEROVÁ, E., ©EDIVÝ, P. (2004). Experimental certification of FEM calculation of sandwich materials on supporting steady head in car industry. In: Experimental stress analysis 2004. Plzeň: ©koda Výzkum, 2004. pp. 19-22. ISBN 80-239-2964-X.
    2. CHALUPA, M., VĚCHET, S., HOUFEK, L. (2010). Methodology of velocity and acceleration measurement of track link of track vehicle with usage of GPS. Publishing department of University of defence, Brno, CR, 2010, pp. 20, ISBN 978-80-7231-773-8.
    3. KOUCKÝ, M., VALI©, D. (2011). Suitable approach for non-traditional determination of system health and prognostics. In: Zeszyty naukowe, Styczen - Marzec, 2011, Vol. 1, No 159, pp. 123-134. ISSN 1731 - 8157. Go to original source...
    4. POLACH, P., HAJ®MAN, M. (2008): Design of Characteristics of Air-Pressure-Controlled Hydraulic Shock Absorbers in an Intercity Bus. Multibody System Dynamics, Springer Netherlands, Dordrecht (The Netherlands), Vol. 19, No. 1-2, pp. 73-90, February 2008. Go to original source...
    5. SVOBODA, M., SOUKUP, J. (2013). Verification of Numeric Solution by Experiment for Examination Vertical Oscillation of a Mechanical Systém, Manufacturing technology, December 2013, vol. 13, No 4, pp. 559 - 563. ISSN 1213 - 2489. Go to original source...
    6. SKOČILAS, J., SKOČILASOVÁ, B., SOUKUP, J. (2013). Determination of the theological properties of thin plate under transient vibration. In: Latin American Journal of Solids and Structures. Vol. 10 (2013), No 1, pp. 187-193. Brazilian society for mechanics and engineering science. ISSN 1679-7817 (print), 1679-7825 (online). Go to original source...
    7. SVOBODA, M., SOUKUP, J. (2013). The Influence of Geometry, Manufacturing Asymmetry and Asymmetric Excitation on Vertical Vibration of a Mechanical System. In: Applied Mechanics and Materials, vol. 302 (2013), pp. 429-434. Trans Tech Publications, Switzerland. Go to original source...
    8. SVOBODA, M., SOUKUP, J. (2013). Dynamic Measurement of Four-Axle Railway Wagon, Manufacturing technology, December 2013, vol. 13, No 4, pp. 563 - 568. ISSN 1213 - 2489. Go to original source...

    Return to the content