Manufacturing Technology 2017, 17(1):121-125 | DOI: 10.21062/ujep/x.2017/a/1213-2489/MT/17/1/121

Influence of the Workpice Quality on the Cutting Tool Life when Gear Wheel are Machined

Miroslav Zetek, Ivana Zetková
Regional Technological Institute, Univerzity of West Bohemia, Univerzitni 8, 306 14 Plzen, Czech Republic

The stability of the machining process is depending on the machined materials properties. But the material properties are influence by the heat treatment process and in this case it is forging. For these study three different company made the "same" forging process and then the material properties are evaluated and their influences on the cutting process were monitored. For the tests the steel DIN 18 CrNiMo 6-7 was used. This material is typically used for the gear wheels where the cutting tools by tool steel is used for the machining. So for the tests the mills from tool steel were used and during the machining the cutting tool life and cutting forces were monitored.

Keywords: Gear wheel, Material analysis, Cutting tool wear, Cutting tool life, Cutting forces

Published: February 1, 2017  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Zetek M, Zetková I. Influence of the Workpice Quality on the Cutting Tool Life when Gear Wheel are Machined. Manufacturing Technology. 2017;17(1):121-125. doi: 10.21062/ujep/x.2017/a/1213-2489/MT/17/1/121.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open article abstract

    References

    1. YOUNES RAMDANE, HAMZAOUI NACER, OUELAA NOUREDINE, DJEBALA ABDERRAZEK (2015). Perceptual study of the evolution of gear defects, Applied Acoustics 99 (2015) 60-67. Go to original source...
    2. GU, L., XU, J., LUO, S. (2016). The design of new cycloid gear with variable cross section and the research of end milling in five-axis machine tool, Manufacturing Technology, Volume 16 (3), 2016, pp. 497-502 Go to original source...
    3. DUBOVSKA, R., MAJERIK, J. (2015). The Research Analysis of Surface Finish and Wear on the Special Tribological Device, Procedia Engineering 100 (2015) 730-736. Go to original source...
    4. SIECLA, R., LEGUTKO, S. (2012). Gear-shaper cutter with curvilinear side flank face, Manufacturing Technology, Volume 12, Issue 13, 2012 Go to original source...
    5. ADIS J. MUMINOVIC, ISAD SARIC, NEDZAD REPCIC (2015). Numerical Analysis of Stress Concentration Factors, Procedia Engineering 100 (2015) 707-713. Go to original source...
    6. DUBOVSKA, R., JAMBOR, J., MAJERIK, J (2014). Qualitative Aspects of Machined Surfaces of High Strength Steels, Procedia Engineering 69 (2014) 646 - 654. Go to original source...
    7. BERÁNEK, L., KOLAŘÍK, K. (2014). Surface integrity analysis of duplex steel by design of experiment approach, Procedia Engineering 69 (2014) 630 - 637. Go to original source...
    8. MORAVČÍKOVÁ, J. (2015). Cutting Material Influence on the Quality of the Machined Surface, Procedia Engineering 100 (2015) 328 - 333. Go to original source...
    9. MARCO SORTINOA, SANDRO BELFIO, GIOVANNI TOTIS, ELSO KULJANIC, GIOVANNI FADELLI, Innovative Tool Coatings for Increasing Tool Life in Milling
    10. VOPÁT, T., PETERKA, J., ŠIMNA, V., KURUC, M. (2015). The Influence of Different Types of Copy Milling on the Surface Roughness and Tool Life of End Mills, Procedia Engineering 100 (2015) 868 - 876 Go to original source...

    Return to the content