Manufacturing Technology 2018, 18(4):538-544 | DOI: 10.21062/ujep/134.2018/a/1213-2489/MT/18/4/538
The Influence Surface Treatment on the Firmness of Spot Welds
- Czech University of Life Sciences Prague, Faculty of Engineering, Department of Material Science and Manufacturing Technology, 165 21 Prague 6 Suchdol, Czech Republic
. Spot welding is a commonly used technology in practice to join metal material. It applies to all types of production, mass, series and piece production. Its biggest advantage is the high productivity, with which it is possible to weld. As with other welding methods, the cleanliness of the welded surfaces is important. The aim of the tests performed was to evaluate the influence surface treatment on the firmness of the test specimens of spot welds. The test specimens were made from steel. Welding was done while using manual clamp welders. Four sets of metal sheets were prepared before the welding, with different surface treatment - surface without treatment (original, not degreased), only degreased, grinded and degreased, blasted and degreased. The test specimens were made using different welding times, from 0.1 sec. to 2.0 sec. Then, they were loaded on a universal test instrument until destruction. All measured values were statistically evaluated. The evaluations show that although it is possible to weld sheets without surface treatment, it is not recommended. There is no statistically significant difference between the results of other types of pre-treatments.
Keywords: resistance welding, hand held spot welder, steel sheets, shear testing resistance spot welds, laboratory test
Published: September 1, 2018 Show citation
References
- BLAŠČÍK, F. et al. (1987). Technológia tvárnenia, zlievárenstva a zvárania. (Technology of Forming, Founding and Welding). Bratislava, ALFA, 832. (In Czech and Slovak).
- BROCKMANN, W. et al. (2009). Adhesive bonding: materials, applications and technology. Wiley-VCH, Weinheim. 414.
- BROŽEK, M. (2016). Resistance spot welding of steel sheets. Manufacturing Technology. 16 (4), 662-666.
Go to original source...
- BROŽEK, M. (2014). Working variables optimization of resistance spot welding. Manufacturing Technology. 14 (4), 522-527.
Go to original source...
- BROŽEK, M. (2013). Soldering sheets using soft solders. Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis. 61(6), 1597-1604.
Go to original source...
- BROŽEK, M. (2013). Optimization of adhesive layer thickness at metal bonding using quick-setting adhesives. Manufacturing Technology. 13 (4). 419-423.
Go to original source...
- HAYAT, F., SEVIM, I. (2012). The effect of welding parameters on fracture toughness of resistance spot-welded galvanized DP600 automotive steel sheets. International Journal of Advanced Manufacturing Technology. 58 (9-12), 1043-1050.
Go to original source...
- HOLÁSEK, J. (1968). Odporové zváranie. (Resistance welding). Bratislava, Slov. vydav. technické literatury, 301.
- KOLAŘÍK, L., SAHUL, M., KOLAŘÍKOVÁ, M., SAHUL, M., TURŇA, M., FELIX, M. (2012). Resistance Spot Welding of Dissimilar Steels. Acta Polytechnica. 52(3), 43-47.
Go to original source...
- LIU, H., XU, X., ZHANG, X. (2013). Optimization of parameters and research on joint microstructure of resistance spot welding for 316 stainless steel. Advanced Materials Research. 652-654, 2326-2329.
Go to original source...
- NIPPES, E. F. (1983). Metals Handbook. Vol. 6., Welding, Brazing, and Soldering. Metal Park, ASM International, 1152.
- PEASURA, P. (2011). The influence of welding parameters on effected the complete for resistance spot welding on mild steel. Advanced Materials Research. 214, 113-117.
Go to original source...
- PLÍVA, L. (1975). Odporové svařování (Resistance welding). Praha, NTL, 265. In Czech.
- Pouranvari, M. (2011). Effect of resistance spot welding parameters on the HAZ softening of DP980 ferrite-martensite dual phase steel welds. World Applied Sciences Journal. 15 (10), 1454-1458.
- RUŽA, V. (1988). Pájení. [Soldering.] SNTL, Praha. 452.
- SVÍTIL, A. (1980). Odporové bodové svařování tenkých pozinkovaných ocelových plechů. (Resistance spot welding of thin galvanized steel sheets). Praha: b. t., 210. In Czech.
- WANG, Z., WANG, Y., ZHANG, D. (2013). Optimization on parameters of resistance spot welding process for galvanized steel plate. Advanced Materials Research. 658, 178-181.
Go to original source...
- ZHANG, H., SENKARA, J. (2012). Resistance Welding: Fundamentals and Applications. 2nd Ed., Boca Raton, CRC Press. 436.
- ČSN EN ISO 4063 (2010). Svařování a příbuzné procesy - Přehled metod a jejich číslování (Welding and allied processes - Nomenclature of processes and reference numbers). Praha, ČNI, 24. In Czech.
- ČSN EN ISO 14273 (2003). Rozměry vzorku a postup zkoušení střihem odporových bodových, švových a výstupkových svarů (Specimen dimensions and procedure for shear testing resistance spot, seam and embossed projection welds). Praha, ČNI, 24. In Czech.
- ČSN EN ISO 4287 (1999). Geometrické požadavky na výrobky (GPS) - Struktura povrchu: Profilová metoda - Termíny, definice a parametry struktury povrchu (Geometrical product specifications (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters). Praha, ČNI, 24. In Czech.
- ČSN 41 1321 (1987). Ocel 11 321 (Steel 11 321). Praha, ČNI, 2. In Slovak.
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.