Manufacturing Technology 2018, 18(4):585-592 | DOI: 10.21062/ujep/142.2018/a/1213-2489/MT/18/4/585

The Study of the Effect of Mechanical and Heat Treatment on the Crystal Texture of Cold Drawn Seamless Tubes

Pavel Kejzlar1, Ondøej Seibert1, Zuzana Andr¹ová1, Peter Burik2
1 Technical University of Liberec. Studentska 1402/2, 461 17, Liberec. Czech Republic
2 ®P VVC, s.r.o. Kolkáreò 35, 976 81 Podbrezová. Slovakia

Seamless tubes are the strongest amongst all tubes types and have a homogeneous structure throughout their length. They are typically manufactured by cold drawing where strong grain deformation takes place. EBSD was used to evaluate the changes of grain structure and texture connected with tubes manufacturing from the initial state over the cold drawing with a stationary plug to subsequent recrystallization annealing.

Keywords: Structure, Texture, Grain, EBSD, Drawing, Deformation

Published: September 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Kejzlar P, Seibert O, Andr¹ová Z, Burik P. The Study of the Effect of Mechanical and Heat Treatment on the Crystal Texture of Cold Drawn Seamless Tubes. Manufacturing Technology. 2018;18(4):585-592. doi: 10.21062/ujep/142.2018/a/1213-2489/MT/18/4/585.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. BRESING, K.H., SOMMER, B. (2008). Steel Tube and Pipe Manufacturing Process. Salzgitter Mannersmann Rohrenwerke.
    2. LOHARKAR, P. K., PRADHAN M. K. (2017) Modeling and Analysis of Cold Drawing Process. In: Handbook of Research on Manufacturing Process Modeling and Optimization Strategies (R. Das, M. Pradhan, (Ed.)), pp. 40-53 IGI Global, Advances in Logistics, Operations, and Management Science. ISBN 9781522524403. Go to original source...
    3. LINARDON, C. (2013). Precision tube drawing for biomedical applications : Theoretical, Numerical and Experimental study. Université de Grenoble.
    4. RAJI, N. A., OLUWOLE O. O. (2011). Influence of Degree of Cold-Drawing on the Mechanical Properties of Low Carbon Steel. In: Materials Sciences and Applications, Vol. 02, No.11, pp. 1556-1563. ISSN 2153-117X. Go to original source...
    5. BELYAKOV, A, et. al. (2004). Microstructure Evolution in Ferritic Stainless Steels during Large Strain Deformation. In: MATERIALS TRANSACTIONS, Vol. 45, No.9, pp. 2812-2821. ISSN 1345-9678. Go to original source...
    6. SCHWARTZ, A. J. (2009). Electron backscatter diffraction in materials science. 2nd ed. New York: Springer. ISBN 978-0-387-88136-2. Go to original source...
    7. ADAMS, B. L., KALIDINDI, S. R., FULLWOOD D. T. (2013). Electron Backscatter Diffraction Microscopy and Basic Stereology. In: Microstructure Sensitive Design for Performance Optimization. Elsevier, pp. 341-371. ISBN 9780123969897. Go to original source...
    8. KEJZLAR, P., MACHUTA, J., NOVÁ, I. (2017). Comparison of the structure of CuZn40MnAl alloy casted into sand and metal moulds. In: Manufacturing Technology. Univerzita J. E. Purkynì, Vol.17, No.1, pp. 44-48. ISSN 12132489. Go to original source...
    9. TREGLER, M., et. al. (2016). The study of deformation behaviour of DC06 deep drawing steel. In: Manufacturing Technology. Vol. 16, No. 1, pp. 284-289. ISSN 12132489. Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content