Manufacturing Technology 2018, 18(4):692-696 | DOI: 10.21062/ujep/162.2018/a/1213-2489/MT/18/4/692

Tribological Mechanism in Machining and Its Use

Karol Vasilko
Faculty of Manufacturing Technologies Technical University of Košice, Bayerova 1, 080 01 Prešov, Slovakia

It is a well-known fact that during cutting there occurs an extremely high degree of chip plastic deformation [1,4,5,11] These deformation structures require attention as they influence technical and economical results of cutting (cutting forces, quality of machined surface, tool wear, cutting temperature) [8,9,15,21]. The paper analyses the options of influencing the deformation field in chip with the aim to improve cutting proces.

Keywords: machining, plastic deformation, chip forming,cutting force

Published: September 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Vasilko K. Tribological Mechanism in Machining and Its Use. Manufacturing Technology. 2018;18(4):692-696. doi: 10.21062/ujep/162.2018/a/1213-2489/MT/18/4/692.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. AHN, A. H et all. (2006). Investigation of cutting characteristics in side-milling a multi-thread shat on automatic lathe. Annals of the CIRP Vol. 55/1/2006, pp.63-66 Go to original source...
    2. BLAŠKOVIČ, P., BALLA, J., DZIMKO, M. (1990). Tribológia. Bratislava: ALFA,1990, 360 s., ISBN 80-05-00633-0
    3. GRANOVSKIJ, G. I., GRANOVSKIJ, V. G. (1985). Rezanije metallov. Moskva: vyššaja škola, 1985, 304 s.
    4. GRZESIK, W. (1998). Podstawy skawania materialow metalowych. Warszawa: Wydawnictwa Naukowo-Techniczne, 1998, 380 s.,ISBN 83-204-2311-2
    5. HOSHI, K., HOSHI, T. (1969). On the metal cutting mechanism with the built-up edge. Mem. Fac. Engng. Hekkaide University 12, č.3, 1969
    6. HRONEK, O., ZETEK, M., BAKSA, T.,ADÁMEK, P. (2018). Surface quality analysis of cutting tool microgeometry to achieve higher durability. Manufacturing Technology, 2018, Vol. 18, No.1, pp. 30-46. Go to original source...
    7. KACZMAREK, J., WOJCIECHWICZ, B. (1995). Zmjany w strategii badaň eksloatacyjnej warstwy wierzchniej. Tribologia č. 6, 1995, s. 629 - 654.
    8. KALPAKJIAN, S. (1999). Manufacturing engineering and technology. New York: Addison Wesley Publishing Company, 1989, pp.1999, ISBN 0-201-12849-7
    9. KOCMAN, K.. PROKOP, J. (2008). Cutting Tools for Matral Turning. Manufacturing Technology, 2008, Vol IV., pp. 5-10.
    10. KOVAČ, P., MILIČIČ D. Rezanje metala Novi Sad: Univerzitet u Novom Sadu, 240 s., ISBN 86.899-0015-1
    11. LOLADZE, T. N. (952). Stružkoobrazovanije pri rezanii metallov. Moskva, Mašgiz, 1952
    12. MASUDA, K. (1970). Compressive strenght of the cutting edges of the WC-Co cemented carbides. Bulletin ASME, 13, č. 56, 1970 Go to original source...
    13. MRKVICA, I et al. (2012). Cutting ceramic by turning of nickel alloy. Manufacturing Technology, Vol 12, No. 13, 2012, pp. 174-186. Go to original source...
    14. OPITZ, H., SCHILLING, W. (1967). Untersuchung der Verschleiβreaktionen bei der Bearbeitung von Stahl mit Echnellarbeitsstahlwerkzeugen. Forschungsber Lande s Nordhein-Westfalen, 1967, Nr. 1796, 95 s. Go to original source...
    15. REZNIKOV, A. N. (1969). Teplofizika rezanija. Moskva, Mašinostrojenije, 1969. 286 s. Go to original source...
    16. SALVO, G. J., SHAW, M.C. (1968). Hydrodymanic action at a chip-tool interface. Advance s Machining Tool Design and Research., Part. 2, 1968
    17. SIMONEAU, A., ELBESTAWI, M.A. (2006). The effect of Microstructure on chip formation and surface defect in microscale, microscale, and macroscale cutting of Steel. Annals of the CIRP vol. 55/1/2006, pp.97-102. Go to original source...
    18. STEPHENSON, D. A., AGAPIOU, J. S. (2006). Metal Cutting Theory and Practice. Taylor &Francis, USA, 2006, 846 pp.
    19. TRENDT, E. M. (1991). Metal Cutting. London - Boston: Ed. Oxford, Butterworths - Helnemann, 1991, 273 s., ISBN 0-7506-1068-9
    20. VASILKO, K. MÁDL, J. (2012). Teorie obrábění. Ústí n. Labem: UJEP, 2012, 526 s.
    21. WRIGHT, P. K. (1977). Applications of the Experimental Methods Used to Determine Temperature Gradients. In: Cutting Tools. Austrial Conference Manufacturing Engineering., Adelaide, 1977. Barton, 1977, pp. 145-149

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content