Manufacturing Technology 2018, 18(6):950-953 | DOI: 10.21062/ujep/206.2018/a/1213-2489/MT/18/6/950

The Effect of Different Modifiers on Cutting Temperature in Turning of AlSi7Mg0.3 Alloy

Michal Martinovsky, Jan Madl
Faculty of Mechanical Engineering, J. E. Purkyne University, Pasteurova 3334/7, 400 01, Usti nad Labem, Czech Republic

One of the problems in machining Al alloys represents machinability of these materials. Machinability is a characterised by several characteristics. One of these characteristics is a cutting temperature. This paper is focused on the effect of selected modifiers in AlSi7Mg0.3 alloy on this temperature. Several variants of this material modified by strontium, calcium and antimony are used. All these materials are compared with non-modified alloy. Moulded castings of non-modified alloy and for each modified variant were made. Gravity-die castings into a metal mould with a thermal insulation were used.

Keywords: AlSi7Mg0.3 alloy, Modifiers, Machining, Machinability

Published: December 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Martinovsky M, Madl J. The Effect of Different Modifiers on Cutting Temperature in Turning of AlSi7Mg0.3 Alloy. Manufacturing Technology. 2018;18(6):950-953. doi: 10.21062/ujep/206.2018/a/1213-2489/MT/18/6/950.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. MADL, J., KOUTNY, V. (2000). Machinability Tests of Aluminium Alloys. In: MATAR, FS ÈVUT, Praha, pp. 124-127.
    2. MADL, J., RUZICKA, L., LATTNER, M. (2013). The Effect of Chemical Elements on the Machinability of Aluminium Alloys. Manufacturing Technology, Vol. 13, No. 3, pp. 349-353. ISSN 1213-2489. Go to original source...
    3. KOCMAN, K. (2004). Specialni technologie obrabeni. FSI VUT, Brno, pp.155, ISBN 80-214-2562-8.
    4. STEFAN MICHNA et al. (2007). Aluminium Materials and Technologies from A to Z. Adin, Presov, p. 632. ISBN 9789-80-89244-18-8.
    5. ALUMINIUM TASCHENBUCH (1988). Aluminium-Verlag, Dusseldorf, pp. 234.
    6. LIPINSKI T. (2017). Analysis of Mechanical Properties of AlSi9Mg Alloy with Ti and B Additions. Manufacturing Technology, Vol. 17, No. 5, pp. 761-766. ISSN 1213-2489. Go to original source...
    7. CAIS, J., SVOBODOVA, J., STENCEKOVA, D. (2017). Modification of AlSi7Mg0.3 Alloy Using Antimony. Manufacturing Technology, Vol. 17, No. 5, pp. 685-690. ISSN 1213-2489. Go to original source...
    8. BOLIBRUCHOVA, D., TILLOVA, E. (2005). Zlievarenske zliatiny Al-Si, ZU, Zilina, pp. 180. ISBN 80-87-485-6.
    9. MARTINOVSKY, M., MADL, J. (2014). Vliv modifikatoru na obrobitelnost a vlastnosti Al-Si slitin. Strojírenská technologie, Vol. 14, No. 3, FVTM UJEP, Usti ad Labem, pp. 212-219. ISSN 1211-4162.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content