Manufacturing Technology 2018, 18(6):967-972 | DOI: 10.21062/ujep/209.2018/a/1213-2489/MT/18/6/967

Experimental Study of the Durability of Cutting Tips Prepared via Powder and Casting Metallurgy

Peter Monka1, Katarina Monkova1,2, Libu¹e Sıkorová2, Martin Novak3
1 TU Kosice, Faculty of Manufacturing Technologies with the seat in Presov, Sturova 31, 080 01 Presov, Slovakia
2 UTB Tomas Bata University in Zlin, Faculty of Technology, Vavreckova 275, 760 01 Zlin
3 Faculty of Mechanical Engineering, J. E. Purkynì University in Ústí nad Labem, Pasteurova 3334/7, 400 96 Ústí nad Labem, Czech Republic

Machining has long been the most used technology in manufacturing processes. On the other hand, new materials are being developed or new ways of preparing them are being developed. One of such materials is High Speed Steel (HSS). The article deals with experimental study of a cutting tool durability prepared via powder and casting metallurgy. Durability of cutting tips produced from HSS Vanadis 30 (SN 41 9830) were tested during the short-term radial tests. Three modifications of the HSS steel were studied, while two types of them were prepared via powder metallurgy and the third one was made via casting metallurgy. The measured values were statistically processed and submitted to the remoteness testing according to Grubbs. The results have shown that the most appropriate material for production of cutting tips, ranked based on three studied steels from the durability point of view, appears Vanadis 30 produced via powder metallurgy alloyed by component Nb.

Keywords: durability, cutting tip, high speed steel, metallurgy, lathe-turning test

Published: December 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Monka P, Monkova K, Sıkorová L, Novak M. Experimental Study of the Durability of Cutting Tips Prepared via Powder and Casting Metallurgy. Manufacturing Technology. 2018;18(6):967-972. doi: 10.21062/ujep/209.2018/a/1213-2489/MT/18/6/967.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. ZHONG, H. et al. (2010) Development of powder metallurgy high speed steel, Materials Science Forum, Trans Tech Publications. Switzerland, Vols. 638-642, pp. 1854-1859. Go to original source...
    2. MESQUITA, R. A., BARBOSA, C. A. (2009) HSS Produced Through Conventional Casting, Spray Forming and Powder Metallurgy, Brazil, 6th International tooling conference, pp. 387-402.
    3. RODZINAK D., HVIZDOS, P. et al. (2010) The effect of pin hardness on wear of sintered materials, In: Manufacturing Engineering, Vol. 9(3), pp. 36-39.
    4. Patent n. 281966 (2001), conferrable 13.6. 2001, author: M. Miskovicova et al., owner: Institute of Material Research, Slovak Academy of Science Kosice.
    5. HANZL, P., ZETKOVA, I., MACH, J. (2017) Optimization of the Pressure Porous Sample and Its Manufacturability by Selective Laser Melting, Manufacturing Technology, Vol. 17(1), pp. 34 - 38. Go to original source...
    6. MATESA, B., KOZAK, D., STOIÆ, A., SAMARD®IÆ I. (2011) The influence of heat treatment by annealing on clad plates residual stresses, Metalurgija, Vol. 50(4), pp. 227-230.
    7. KROLCZYK, G. et al. (2015) Investigation of selected surface integrity features of duplex stainless steel (DSS) after turning, Metalurgija, Vol. 54(1), pp. 91-94.
    8. TEMUCIN, T. et al. (2013) A fuzzy based decision support model for non-traditional machining process selection, Technical Gazette, Vol. 20(5), pp. 787-793.
    9. VYCHYTIL, J., HOLECEK, M, (2010) The simple model of cell prestress maintained by cell incompressibility, Mathematics and computers in simulation, 80(6), 1337-1344. Go to original source...
    10. BURECEK, A., HRUZIK, L. VASINA, M. (2017) Dynamics of Linear Hydraulic Cylinder with Mass Load, Manufacturing Technology, Vol. 17(3), pp. 296-302. Go to original source...
    11. PETRU, J. et al. (2013) Influence of cutting parameters on heat-affected zone after laser cutting, Tehnicki Vjesnik, Vol. 20(2), pp. 225-230.
    12. MONKA, P. (2016) Design and experimental study of turning tools with linear cutting edges and comparison to commercial tools, Int J Adv Manuf Technology, 85, pp. 2325-2343. Go to original source...
    13. JURKO, J. (2011) Verification of cutting zone machinability during the turning of a new austenitic stainless steel, Adv. Comp. Sci. Edu. Appl., 202(2), pp. 338-345. Go to original source...
    14. MALOTOVA, S. (2016). Roughness Evaluation of the Machined Surface at Interrupted Cutting Process, Manufacturing Technology, Vol. 16(1), pp. 168-173. Go to original source...
    15. ZETEK, M., ZETKOVA, I. (2017) Influence of the Workpice Quality on the Cutting Tool Life when Gear Wheel are Machined, Manufacturing Technology, Vol. 17(1), pp.121-125. Go to original source...
    16. CEP, R. et al. (2014) Surface roughness after machining and influence of feed rate on process, Key Engineering Materials, Vol. 581, pp. 341-347. Go to original source...
    17. KADAROVA, J., MIHOK, J. et al. (2013) Proposal of performance assessment by integration of two management tools, In: Quality Innovation Prosperity 17(1), pp. 88-103. Go to original source...
    18. CIZMAR, J.: Diploma thesis, FMT TU Kosice with seat in Presov (2002).
    19. UNGUREANU, M. et al. (2015) Product Innovation Management for Business Development, Proceedings 5th Central European Conference in Regional Science (CERS), pp. 1112 - 1118.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content