Manufacturing Technology 2018, 18(6):1041-1047 | DOI: 10.21062/ujep/221.2018/a/1213-2489/MT/18/6/1041

Towards the Prediction of Micro-EDM Drilling Performance on WC Varying the Hole Depth

Gianluca D'Urso, Mariangela Quarto, Giuseppe Pellegrini, Chiara Ravasio
University of Bergamo - DIGIP, Viale Marconi 5, 24044 Dalmine (BG) - Italy

The present work deals with the execution of through micro-holes on tungsten carbide plates using a micro-EDM (Electrical Discharge Machining) machine. The investigation focuses on the monitoring of the performance during the drilling phase in order to obtain the in progress behavior of the performance indexes. The experiments were carried out by varying some process parameters such as peak current, voltage and frequency to achieve both high and low power discharge conditions. Regarding electrodes, the most commonly industrial used ones were selected: tubular tungsten carbide and brass. The performance indexes taken into account were machining time, Material Removal Rate (MRR), Tool Wear (TW) and Tool Wear Ratio (TWR). Brass electrode always resulted to be the best solution in terms of drilling speed even though the wear of this electrode type is remarkable higher than the tungsten one. The evolution of the performance indexes during the drilling operation showed the same trend for both electrodes: increasing the hole depth, the drilling operation proceeds in a more difficult way, due to the evacuation of debris that becomes more difficult and therefore the performance indexes get worse. Finally, the technology windows of the cumulated MRR and TWR were defined for both electrode materials, in order to predict the micro EDM process performance varying the hole depth.

Keywords: Micro-EDM, Tungsten carbide, Micro-drilling, Process performance, Prediction ability

Published: December 1, 2018  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
D'Urso G, Quarto M, Pellegrini G, Ravasio C. Towards the Prediction of Micro-EDM Drilling Performance on WC Varying the Hole Depth. Manufacturing Technology. 2018;18(6):1041-1047. doi: 10.21062/ujep/221.2018/a/1213-2489/MT/18/6/1041.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. CHETAN, GHOSH, S., RAO, P.V. (2015). Application of sustainable techniques in metal cutting for enhanced machinability: a review. In: Journal of Cleaner Production, Vol. 100, pp. 17 - 34. Go to original source...
    2. SONA, S.M., LIMB, H.S., KUMARB, A.S., RAHMAN, M. (2007). Influences of pulsed power condition on the machining properties in micro EDM. In: Journal of Materials Processing Technology, Vol. 190, pp. 73 - 76. Go to original source...
    3. MOURALOVA, K., BENES, L., ZAHRADNICEK, R. (2017). Defects in the surface layer of pure molybdenum after WEDM. In: Manufacturing Technology, Vol. 17, No. 5, pp. 786-790. Go to original source...
    4. VALAKI, J.B., RATHOD, P.P. (2016). Assessment of operational feasibility of waste vegetable oil based bio-dielectric fluid for sustainable electric discharge machining (EDM). In: Int J Adv Manuf Technol, Vol. 87, pp. 1509 - 1518. Go to original source...
    5. SUNDARAM, M.M., PAVALARAJAN, G.B., RAJURKAN, K.P. (2008). A Study on Process Parameters of Ultrasonic Assisted Micro EDM Based on Taguchi Method. In: Journal of Materials Engineering and Performance, Vol. 17, pp. 210 - 215. Go to original source...
    6. WEULE, H., et al. (2004). International state of the art of micro production technology. In: Production Engineering Research and Development, Vol. 11, No. 1, pp. 29 - 36.
    7. MAHDAVINEJAD, R.A., MAHDAVINEJAD, A. (2005). ED machining of WC-Co. In: Journal of Materials Processing Technology, Vol. 162 - 163, pp. 637 - 643. Go to original source...
    8. JAHAN, MP., RAHMAN, M., WONG, YS. (2011). A review on the conventional and micro-electro discharge machining of tungsten carbide. In: International Journal of Machine Tools & Manufacture, Vol. 51, pp. 837-858. Go to original source...
    9. JAHAN, M.P., WONG, Y.S., RAHMAN, M. (2009). A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator. In: Journal of Materials Processing Technology, Vol. 209, pp. 1706 - 1716. Go to original source...
    10. LEE, S.H., LI, X. (2003). Study of the surface integrity of the machined workpiece in the EDM of tungsten carbide. In: Journal of Materials Processing Technology, Vol. 139, pp. 315 - 321. Go to original source...
    11. MOURALOVA, K., KOVAR, J., KARPISEK, Z., KOUSA, P. (2016). Optimization Machining of Titanium Alloy Ti-6Al-4V by WEDM with Emphasis on the Quality of the Machined Surface. In: Manufacturing Technology, Vol. 16, No. 6, pp. 1326-1331. Go to original source...
    12. WANG, X., CHEN, L., DAN, B., WANG, F. (2018). Evaluation of EDM process for green manufacturing. In: Int J Adv Manuf Technol, Vol. 94, pp. 633 - 641. Go to original source...
    13. D'UURSO, G., MACCARINI, G., MERLA, C., RAVASIO, C. (2011). The influence of electrode shape and material on micro EDM drilling process. In: Proceedings of the 9th International Conference on Multi-Material Micro Manufacture, Vienna, Austria, 2011.
    14. KUPPAN, P., RAJADURAI, A., NARAYANAN, S. (2008). Influence of EDM process parameters in deep hole drilling of Inconel 718. In: International Journal Advanced Manufacturing Technology, Vol. 38, pp. 74 - 84. Go to original source...
    15. DENKENA, B., HOFFMEISTER, H.W., REICHSTEIN, M., ILLENSEER, S., HLAVAC, M. (2006). Micro-machining processes for microsystem technology. In: Microsystem Technology, Vol. 12, pp. 659 - 664. Go to original source...
    16. LEE, S.H., LI, X. (2001). Study of the effect of machining parameters on the machining characteristics in electrical discharge machining of tungsten carbide. In: Journal of Materials Processing Technology, Vol. 115, pp. 344 - 358. Go to original source...
    17. JAHAN, M.P., WONG Y.S., RAHMAN, M. (2009). A study on the fine-finish die-sinking micro-EDM of tungsten carbide using different electrode materials. In: Journal of Materials Processing Technology, Vol. 209, pp. 3956 - 3967. Go to original source...
    18. YILMAZ, O.M., OKKA, A. (2010). Effect of single and multi-channel electrodes application on EDM fast hole drilling performance. In: International Journal Advanced Manufacturing Technology, Vol. 51, pp. 185 - 194. Go to original source...
    19. PHAM, D.T., IVANOV, A., BIGOT, S., POPOV, K., DIMOV, S. (2007). An investigation of tube and rod electrode wear in micro EDM drilling. In: Int. J. Adv. Manuf. Technol, Vol. 33, pp. 103 - 109. Go to original source...
    20. D'URSO, G., LONGO, M., MACCARINI, G., RAVASIO, C. (2011). Electrical discharge machining of micro holes on titanium sheets. In: Proceedings of the 5th International Conference on Micro- and Nanosystems, ICONE14, Washington, DC, USA, 2011. Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content