Manufacturing Technology 2019, 19(5):807-812 | DOI: 10.21062/ujep/376.2019/a/1213-2489/MT/19/5/807
Effect of Sr, Ti and B Additions as Powder and a Preliminary Alloy with Al on Microstructure and Tensile Strength AlSi9Mg Alloy
- University of Warmia and Mazury in Olsztyn, The Faculty of Technical Sciences, St: Oczapowskiego 11, 10-957 Olsztyn, Poland
The initial structure of AlSi9Mg alloy is com posed of granular and acicular β phase, with α phase as matrix. The hard, irregular, often pointed β phase is responsible for the poor mechanical properties of said alloy. This composition is responsible for the alloy's low strength parameters, and it limits the extent of practical applications. This study presents the results of modification of an AlSi9Mg alloy with strontium, boron and titanium in different ranges produced as a melted modifier added as powders and as rod. The influence of the analyzed additions on the microstructure and tensile strength of the silumin was presented in graphs. The used treatments of a hypoeutectic AlSi9Mg alloy improved the alloy's properties. The results of the tests indicate that the mechanical properties of the modified alloy are determined by the sequence in which the components are introduced to the alloy.
Keywords: Al-Si alloy, Silumin, Modification, Mechanical properties
Published: October 1, 2019 Show citation
ACS | AIP | APA | ASA | Harvard | Chicago | IEEE | ISO690 | MLA | NLM | Turabian | Vancouver |
References
- MICHNA, S., LUKAC, I., OCENASEK, V., KORENY, R., DRAPALA, J., SCHNEIDER, H., MISKUFOVA, A. (2005). Encyclopaedia of aluminium. Adin s.r.o. Presov. (in Czech).
- KUBĮSEK J., DALIBOR V., DVORSKŻ D. (2017). Structure and mechanical properties of aluminium alloy sampled from a firefighter ladder. In: Manufacturing Technology, Vol. 17, No 6, pp. 876-881.
Go to original source...
- CHIKOVA, O. A, NIKITIN, K. V., MOSKOVSKIKH, O. P., TSEPELEV, V. S. (2016). Viscosity end electrical conductivity of liquid hypereutectic alloys Al-Si. In: Acta Metallurgica Slovaca, Vol. 22, No. 3, pp. 153-163.
Go to original source...
- LIPIŃSKI, T. (2015). Double modification of AlSi9Mg alloy with boron, titanium and strontium. In: Archives of Metallurgy and Materials, Vol. 60, No. 3B, pp. 2415-2419.
Go to original source...
- MARTINOVSKY, M., MADL, J. (2018). The effect of different modifiers on cutting temperature in turning of AlSi7Mg0.3 alloy. In: Manufacturing Technology, Vol. 18, No. 6, pp. 950-953.
Go to original source...
- KRAUS, P., NĮPRSTKOVĮ, N., JIROUNKOVĮ, K., CAIS, J., SVOBODOVĮ, J. (2018). Effect of heat treatment on the microstructure of the alloy AlSi7CrMnCu2.5. In: Manufacturing Technology, Vol. 18, No. 6, pp. 935-942.
Go to original source...
- PACZ, A. (1921). Alloy. US Patent, No. GB158827. http://www.freepatentsonline.com/1387900.pdf.
- THEILE, W., DUNKEL, E. (1966). In: Giesserei, Vol. 23.
- HUNT, J. D. (1984). Steady state columnar / equiaxed growth of dendrites and eutectics. In: Materials Science and Engineering, Vol. 65, pp. 75-83.
Go to original source...
- MACHUTA, J., NOVĮ, I., KEJZLAR, P., (2017). Structure and mechanical properties of aluminium alloys AlSi10 and AlSi5Mg. In: Manufacturing Technology, Vol. 17, No. 5, pp. 772-777.
Go to original source...
- LYSONKOVA, I., NOVOTNY, J., CAIS, J., MICHNA, S. (2017). Effect of addition of nanoparticles TiO2 into PTFE coating. In: Proceedings of Engineering for Rural Development, Vol. 16, pp. 26-30. Jelgava, Latvia.
Go to original source...
- HREN, I., SVOBODOVA, J. (2018). Fractographic analysis of strontium-modified al-si alloys. In: Manufacturing Technology, Vol. 18, No. 6, pp. 900-905.
Go to original source...
- BOLIBRUCHOVĮ, D., HAJDŚCH, P., BRŁNA, M. (2018). Influence of molybdenum, zircon and copper on structure of aluminum alloy AlSil0Mg(Cu) (En Ac-43200). In: Manufacturing Technology, Vol. 18, No. 5, pp. 709-718.
Go to original source...
- LIPIŃSKI, T. (2017). Effect of combinative cooled addition of strontium and aluminium on mechanical properties AlSi12 alloy. In: Journal of Achievements in Materials and Manufacturing Engineering, Vol. 83, No. 1, pp. 5-11.
Go to original source...
- KONOVALOV, S. V., ZAGULYAEV, D. V., IVANOV, Y. F., GROMOV, V. E. (2018). Effect of yttrium oxide modification of Al-Si alloy on microhardness and microstructure of surface layers. In: Metalurgija, Vol. 57, No. 4, pp. 253-256.
- NAPRSTKOVA, N., KRAUS, P., STANCEKOVA, D. (2018). Calcium and its using for modification of AlSi7Mg0.3 alloy from view of final microstructure and hardness. In: Proceedings of Engineering for Rural Development, Vol. 17, pp. 2003-2008. Jelgava, Latvia.
Go to original source...
- NOVAK, M., NAPRSTKOVA, N., RUZICKA, L. (2012). New ways in aluminium alloys grinding. In: Key Engineerings Materials, Vol. 496, pp. 132 - 137.: Precision Machining IV. TTP. Zurich.
Go to original source...
- LIPIŃSKI, T. (2016). Modification of the Al-9%SiMg alloy with aluminum, boron, and titanium fast cooled mixtures. In: Acta Phisica Polonica A, Vol. 130, No. 4, pp. 982-984.
Go to original source...
- KURZ, W., FISHER, D. J. (1986). Fundamentals of Solidifications. TTP. Switzerland.
- ELLIOTT, R. (1983). Eutectic Solidification Processing, Butterworts, London.
Go to original source...
- LIPIŃSKI, T. (2015). Influence of surface refinement on microstructure of Al-Si cast alloys processed by welding method. In: Manufacturing Technology, Vol. 15, No. 4, pp. 576-581.
Go to original source...
- WO£CZYŃSKI, W., GUZIK, E., WAJDA, W., JEDRZEJCZYK, D., KANIA, B., KOSTRZEWA, M. (2012). Cet in solidifying roll - thermal gradient field analysis. In: Archives of Metallurgy and Materials, Vol. 57, No. 1, pp. 105-117.
Go to original source...
- GÓRAL A., JURA J., BOUZY, E., BIEDA, M., LITYŃSKA-DOBRZYŃSKA, L. (2006). Effect of directional crystallization rate on microtexture of Al-CuAl2 eutectic alloy. In: Archives of Metallurgy and Materials, Vol. 51, pp. 565-568.
- ZAGULIAEV, D., KONOVALOV, S., IVANOV, Y., GROMOV, V. (2019). Effect of electron-plasma alloying on structure and mechanical properties of Al-Si alloy. In: Applied Surface Science, Vol 498, 143767 (on line).
Go to original source...
- LIPIŃSKI, T., SZABRACKI, P. (2015). Mechanical properties of AlSi9Mg alloy with a sodium modifier. In: Solid State Phenomena, Vol. 223, pp. 78-86. TTP. Switzerland.
Go to original source...
- LIPINSKI, T. (2018). Influence of Ti and melt number on microstructure and mechanical properties of Al-Si alloy on agriculture machine parts. In: Proceedings of Engineering for Rural Development, Vol. 17, pp. 1431-1436. Jelgava, Latvia.
Go to original source...
- BOLIBRUCHOVĮ, D., MATĢJKA, M. (2018). Analysis of microstructure changes for alsi9cu3 alloy caused by remelting. In: Manufacturing Technology, Vol. 18, No. 6, pp. 883-888.
Go to original source...
- ULEWICZ, R. (2003). Quality control system in production of the castings from spheroid cast iron. In: Metalurgija, Vol. 42 No. 1 pp. 61-63.
- BOTKO, F., HATALA, M., MITALOVA, Z., CEP, R., RIMAR, M., BERNAT, A., VYBOSTEK, J. (2018). Qualitative evaluation of machined surface of aluminum alloy AlCu4Mg1 depend on feed rate. In: Manufacturing Technology, Vol. 18, No. 2, pp. 201-207.
Go to original source...
- WO£CZYŃSKI, W., KWAPISIŃSKI, P., IVANOVA, A. A., OLEJNIK, E. (2017). Control of structural zones formation and hard particles motion in the brass ingots. In: Archives of Metallurgy and Materials, Vol. 62, No. 4, pp. 2461-2467.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.