Manufacturing Technology 2020, 20(5):660-667

Influence of the Assembly Method of Sleeve Joints on Their Strength

Anna Rudawska1, Izabela Miturska1, Magd Abdel Wahab2, Dana Stančeková3, Miroslava «avodová4
1 Lublin University of Technology, Faculty of Mechanical Engineering, Nadbystrzycka 36, 20-618 Lublin
2 Ghent University, Faculty of Engineering and Architecture, Zwijnaarde, Sint-Pietersnieuwstraat 41, 9000 Ghent, Belgium
3 University of Zilina, Faculty of Mechanical Engineering, Department of Machining and Manufacturing Technologies, Univerzitna 8215/1, 010 26 ®ilina, Slovakia
4 Technical University in Zvole, Faculty of Environmental and Manufacturing Technology, ©tudentská 26, 960 01 Zvolen, Slovakia

The aim of the study was to compare the strength of assembly joints of sleeve elements made of different structural, polymeric materials. Experimental tests were carried out to determine the mechanical properties of adhesive and welded joints. Adhesive joints were made of polyvinyl chloride pipes with the use of three types of adhesives: Epidian 53/PAC/100:80, Epidian 53/TFF/100:22, Vodaro 15010-VO. The welded joints were made of polypropylene pipes. All of the joints have been made with the use of a pipe fitting allowing for correct joints. Then the completed joints were subjected to destructive strength tests. The obtained results made it possible to carry out statistical analysis, which aimed at determining significant differences between the various methods of assembly. The tests carried out proved that the adhesive joints made with the Vodaro 15010-VO one-component adhesive were characterized by the highest strength - 2.30 MPa. The lowest strength was obtained in the case of adhesive joints made with Epidian 53/TFF/100:22 - 0.45 MPa epoxy ad-hesive composition. Statistical analysis showed that the strength obtained in case of adhesive joints made with epoxy compositions differs significantly from the strength of adhesive joints made with Vodaro adhe-sive. No significant differences at the assumed level of significance α=0.05 were also observed in the case of the strength of PP-R adhesive joints made with Vodaro adhesive and the strength of PVC-U welded joints.

Keywords: Adhesive joints, welded joints, sleeve joints

Received: May 1, 2020; Revised: October 18, 2020; Accepted: October 26, 2020; Prepublished online: November 23, 2020; Published: December 14, 2020  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Rudawska A, Miturska I, Wahab MA, Stančeková D, «avodová M. Influence of the Assembly Method of Sleeve Joints on Their Strength. Manufacturing Technology. 2020;20(5):660-667.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. ADAMS, R.D., COMYN, J., WAKE, W.C. (1997). Structural adhesive joints in engineering. Chapman & Hall.
    2. AMANCIO-FILHO, S.T., DOS SANTOS, J.F. (2009). Joining of polymers and polymer-metal hy-brid structures: Recent developments and trends. Polymer Engineering & Science. Vol. 49, No. 8, pp.1461-1476. Go to original source...
    3. ARNOTT, D., RIDER, A., MAZZA, J. (2002). Surface Treatment and Repair Bonding. Advances in the Bonded Composite Repair of Metallic Aircraft Structure. Elsevier. pp. 41-86. Go to original source...
    4. BAZROV, B.M. (2010). Classification of joints. Russian Engineering Research. Vol. 30, No. 4, pp. 399-403. Go to original source...
    5. CHEN, W.-F., KISHI, N., KOMURO, M. (2011). Semi-rigid connections handbook. J. Ross Pub.
    6. DEBROY, T., DAVID, S.A. (1995). Physical processes in fusion welding. In: Reviews of Modern Physics. Vol. 67, No. 1, pp. 85-112. Go to original source...
    7. DOLEZ, P. AND LOVE, B. (2001). Adhesive bonding as an alternative for underwater structural re-pair. Eleventh International Offshore and Polar Engineering Conference. ISOPE, International Socie-ty of Offshore and Polar Engineers. pp. 17-22.
    8. GAUGEL, T., BENGEL, M., MALTHAN, D. (2004). Building a mini- assembly system from a technology construction kit. In: Assembly Automation. Vol. 24, No. 1, pp. 43-48. Go to original source...
    9. GREWELL, D., BENATAR, A. (2007). Welding of Plastics: Fundamentals and New Developments. International Polymer Processing. Vol. 22, No. 1, pp. 43-60. Go to original source...
    10. JASIULEK, P. (2004). Butt welding of polyethylene pipes. In: Instal. No. 4, pp. 40-44.
    11. JEŻEWSKA, A. (2015). Tetrahydrofuran Determination in workplace air with gas chromatography. In: Podstawy i Metody Oceny ¦rodowiska Pracy. Vol. 86, No. 4, pp. 191-202.
    12. KEIBAL, N.A., BONDARENKO, S.N., KABLOV, V.F. (2011). Modification of adhesive composi-tions based on polychloroprene with element-containing adhesion promoters. In: Polymer Science Series D. Vol. 4, No. 4, pp. 267-280. Go to original source...
    13. KOU, S. (2003). Welding metallurgy. In. MRS Bulletin. Vol. 28, No. 9, pp. 674-675. Go to original source...
    14. KRÓLIKOWSKI, W. (2017). Polimerowe kompozyty konstrukcyjne. PWN.
    15. KURUSHINA, V., ZEMENKOV, Y. (2014). Innovative cyclical development of the Russian pipeline system, pp. 881-888. Ekateringburg, Russia. Go to original source...
    16. KUSMIERCZAK, S. (2015). Evaluation of Degradation of Heat Stressed Pipelines, Manufacturing Technology, Vol. 15, No. 6, pp. 1006-1010. Go to original source...
    17. MITURSKA, I., RUDAWSKA, A., MÜLLER, M., VALÁ©EK, P. (2020). The Influence of Modifica-tion with Natural Fillers on the Mechanical Properties of Epoxy Adhesive Compositions after Storage Time. Materials. Vol. 13, No. 2, pp. 291. Go to original source...
    18. MÜLLER, M. (2017). Effect of Surface Treatment of Adhesive Bonded Sheet of Aluminium Alloy EN AW 2024 T3 on Adhesive Bond Strength Created by Means of Structural Two-Component Ad-hesive. Manufacturing Technology. Vol. 17, No. 5, pp. 791-796. Go to original source...
    19. MÜLLER, M. (2017). Effects of Aluminium Microparticles and Surface Treatment of AlCu4Mg on Mechanical Properties of Adhesive Bond Strength. Manufacturing Technology. Vol. 17, No. 1, pp. 66-71. Go to original source...
    20. RUDAWSKA, A. (2019). Comparison of the adhesive joints' strength of the similar and dissimilar systems of metal alloy/polymer composite. Applied Adhesion Science. Vol. 7, No. 1, pp. 7. Go to original source...
    21. RUDAWSKA, A., ABDEL WAHAB, M., MÜLLER, M. (2020). Effect of ageing process on me-chanical properties of adhesive tubular butt joints in aqueous environment. International Journal of Adhesion and Adhesives. Vol. 96, 102466. Go to original source...
    22. RUDAWSKA, A., KUCZMASZEWSKI, J. (2005). Klejenie blach ocynkowanych. Wydawnictwo Politechniki Lubelskiej.
    23. RUDAWSKA, A., MITURSKA, I. (2018). Wpływ warunków utwardzania i sezonowania na wytrzymało¶ć poł±czeń klejowych doczołowych. Technologia i Automatyzacja Montażu. Vol. 4, pp. 48-52.
    24. RUDAWSKA, A., MITURSKA, I., SZABELSKI, J., SKOCZYLAS, A., DRO¬DZIEL, P., BOCIˇGA, E., MADLEŇÁK, R., KASPEREK, D. (2017). Experimental research and statistic analy-sis of polymer composite adhesive joints strength. In: Journal of Physics: Conference Series. Vol. 842, pp. 012074. Go to original source...
    25. RUDAWSKA, A., WIERZCHOWSKI, A., MÜLLER, M., PETRŮ, J., NÁPRSTKOVÁ, N. (2017). The Properties of Regenerative Polymer Mass. Advances in Science and Technology Research Jour-nal. Vol. 11, No. 3, pp. 130-138. Go to original source...
    26. ¦CIESZKA, S.F., ŻOŁNIERZ, M. (2012). Eksploatacja maszyn, czę¶ć 1. Wydawnictwo Politechniki ¦l±skiej,.
    27. SIONKOWSKA, A. (2011). Current research on the blends of natural and synthetic polymers as new biomaterials: Review. In: Progress in Polymer Science. Vol. 36, No. 9, pp. 1254-1276. Go to original source...
    28. WŁOSIŃSKI, W. (2001). Methods of joining of special materials. In: Biuletyn Instytutu Spawalnictwa w Gliwicach. Vol. 45, No. 5, pp. 126-130.
    29. ZHANG, X., MAO, X., ABOURIZK, S.M. (2009). Developing a knowledge management system for improved value engineering practices in the construction industry. In: Automation in Construction. Vol. 18, No. 6, pp/ 777-789. Go to original source...
    30. ŻUCHOWSKA, D. (2000). Polimery konstrukcyjne: wprowadzenie do technologii i stosowania. Wydawnictwa Naukowo-Techniczne.
    31. https://systemy-cisnieniowe.pl/poradniki/klejenie-rur-i-ksztaltek-z-tworzyw-sztucznych/ [access date: 02.01.2020]
    32. ISO/DIS 10365: Adhesives - Designation of main failure patterns.
    33. PN-EN ISO 9311-2:2011 - Adhesives for thermoplastic piping systems -- Part 2: Determination of shear strength.

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content