Manufacturing Technology 2021, 21(4):502-511 | DOI: 10.21062/mft.2021.063

Use of Thermomechanical Analysis in the Design of a Composite System with a Low Coefficient of Longitudinal Thermal Expansion for End Gauges

Dora Kroisová ORCID..., ©těpánka Dvořáčková ORCID..., Petr Kůsa ORCID...
Faculty of Mechanical Engineering, Technical University of Liberec. Studentska 2, 461 17 Liberec. Czech Republic

The work presents the possibilities of using the thermomechanical analysis to design composite systems with carbon fibers, which should have a low coefficient of longitudinal thermal expansion will be potentially valuable in the form of calibrated length gauges. ChS Epoxy 520 epoxy resin (hardener T0492) was used as a matrix for composite production. Carbon fibers were tested in the form of short recycled fibers and continuous fibers in roving and fabric. The values of the coefficient of longitudinal thermal expansion of all prepared systems were determined below the glass transition temperature of the polymer matrix in the temperature range of 5º to 40ºC, i.e., in the range suitable for use in technical practice. From the obtained results, it is evident that carbon fibers significantly influence the epoxy matrix behavior. The coefficients of longitudinal thermal expansion of the epoxy resin in this temperature range from 47.6 to 65.2 [10-6 /K], the coefficients of the composite system with recycled carbon fibers with a random arrangement from 38.6 to 47.6 [10-6/K], coefficients of systems with a parallel array of fibers from to 3.4 to 2.7 [10-6/K] for carbon fibers in the form of roving and 4.3 to 2.0 [10-6/K] for carbon fibers in fabric form.

Keywords: Thermomechanical Analysis, Carbon Fibers, Epoxy Resin, Coefficient of Longitudinal Thermal Expansion
Grants and funding:

It was supported by TAČR project TJ02000175 Research of end gauges in terms of thermal expansion and non-standard material composition. My thanks belong to Miloslav Ledvina with machining composite samples and Martin ©vec for microscopic analysis.

Received: January 23, 2021; Revised: May 28, 2021; Accepted: June 28, 2021; Prepublished online: July 4, 2021; Published: September 18, 2021  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Kroisová D, Dvořáčková ©, Kůsa P. Use of Thermomechanical Analysis in the Design of a Composite System with a Low Coefficient of Longitudinal Thermal Expansion for End Gauges. Manufacturing Technology. 2021;21(4):502-511. doi: 10.21062/mft.2021.063.
Download citation

References

  1. DECKER, J.E. (2001). Some important characteristics of gauge-block artefactsfor international comparison. In: Metrologia, Vol. 38, No. 3, pp. 269. Go to original source...
  2. BERÁNEK, L., KROISOVÁ, D., DVOŘÁČKOVÁ, ©., URBAN, J., ©IMOTA, J., ANDRONOV, V., BURE©, L., PELIKÁN, L. (2020). Use of Computed Tomography in Dimensional Quality Control and NDT. In: Manufacturing Technology, Vol. 20, No. 5, pp. 566 - 575. DOI: 10.21062/mft.2020.108 Go to original source...
  3. URBAN, J., BERÁNEK, L., KOPTI©, M., ©IMOTA, J., KO©«ÁK, O. (2020). Influence of CMM Scanning Speed and Inspected Feature Size on an Accuracy of Size and Form Measurement. In: Manufacturing Technology, Vol 20, No. 4, pp. 538-544. DOI: 10.21062/mft.2020.074 Go to original source...
  4. AGARWAL, B.D., BROUTMAN, L.J.: Vláknové kompozity, SNTL Praha 1987
  5. PIMENTA, S., PINHO, S.T. (2011). Recycling carbon fibre reinforced polymers for structural applications: technology review and market outlook. In: Waste Management, Vol. 31, pp. 378-392. Go to original source...
  6. AGARWAL, G., PATNAIK, A., SHARMA, R.K. (2014). Mechanical and thermo-mechanical properties of bi-directional and short carbon fiber reinforced epoxy composites. In: Eng. Sci. Tech. Vol. 9, pp. 590-604.
  7. DVOŘÁČKOVÁ, ©., KROISOVÁ, D. (2020). Thermal Expansion of Composite System Epoxy Res-in/Recycled Carbon Fibres. In: Material Science Forum, Vol. 994, pp. 162-169. https://doi.org/10.4028/www.scientific.net/msf.994.162 Go to original source...
  8. DONG, K., ZHANG, J., CAO, M., WANG, M., GU, B, SUN, B. (2016). A mesoscale study of thermal expansion behaviors of epoxy resin and carbon fiber/epoxy unidirectional composites based on periodic temperature and displacement boundary conditions. In: Polymer Testing. Vol. 55, pp. 44-60. DOI: 10.1016/j.polymertesting.2016.08.009 Go to original source...
  9. KROISOVÁ, D., DVOŘÁČKOVÁ, ©., LEDVINA, M. (2021). Kalibrované koncové měrky jako etalon pro měření délky zejména v technické praxi. PUV 2021 - 38492 ze dne 26.1. 2021

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.