Manufacturing Technology 2021, 21(5):575-584 | DOI: 10.21062/mft.2021.078
Model of geometric deviations in milling with three error sources
- Dipartimento di Ingegneria Civile e Meccanica, Università degli Studi di Cassino e del Lazio Meridionale, 03043 Cassino. Italy
The milling process is widely used industrially and the quality of the obtained milled products should be controlled because it affects their performance in exercise. This work correlates the quality of the machined surfaces with the adopted locating system, the shape deviations of the workpiece datum and the machine tool. An analytical model was set up and implemented through Matlab® to simulate the quality effects of a milling process. It was applied to two face milling processes characterized by two different locator configurations. It was proved that machine tool volumetric error influences the flatness of the milled surface, while the locator configuration and the datum form deviation affect the orientation of the milled surface, as should be actually.
Keywords: Error model, Geometric source error, Milling accuracy, Locators
Received: June 3, 2021; Revised: July 11, 2021; Accepted: August 27, 2021; Prepublished online: October 21, 2021; Published: November 25, 2021 Show citation
References
- HANZL, P., ZETKOVÁ, I., ZETEK, M. (2020) Comparion of lightweight and solid milling cutter capa-bilities. In: Manufcturing Technology, Vol. 20, No. 1, pp. 23-26. Elsevier, Netherlands. ISSN 1213-2489.
Go to original source...
- BENARDOS, P.G., VOSNIAKOS, G.-C. (2003) Predicting surface roughness in machining: a review. In: International Journal of Machine Tools and Manufacture, Vol. 43, pp. 833-844. Elsevier, Netherlands. ISSN 0890-6955.
Go to original source...
- DENKENA, B., BÖß, V., NESPOR, D., GILGE, P., HOHENSTEIN, S., SEUME, J. (2015) Prediction of the 3D Surface Topography after Ball End Milling and its Influence on Aerodynamics. In: Procedia CIRP, Vol. 31, pp. 221-227. Elsevier, Netherlands. ISSN 2212-8271.
Go to original source...
- GIULIANO, G., POLINI, W. (2021) Weight reduction in an AA2017 aluminium alloy part through the gas forming process of a blank with a variable thickness. In: Manufcturing Technology, Vol. 21, No. 2, pp. 193-199. Elsevier, Netherlands. ISSN 1213-2489.
Go to original source...
- POLINI, W., CORRADO, A. (2020) Digital twin of composite assembly manufacturing process. In: In-ternational Journal of Production Research, Vol. 58, No. 17, pp. 5238-5252. ISSN 00207543.
Go to original source...
- ISO 4287. (2009) Geometrical product specification (GPS) - Surface texture: Profile method - Terms, definitions and surface texture parameters.
- ELBESTAWI, M.A., ISMAIL, F., YUEN, K.M. (1994) Surface topography characterization in finish mill-ing. In: International Journal of Machine Tools and Manufacturing, Vol. 34, pp. 245-255. Elsevier, Netherlands. ISSN 0890-6955.
Go to original source...
- EHMANN, K.F., HONG, M.S. (1994) A Generalized Model of the Surface Generation Process in Metal Cutting. In: CIRP Annals, Vol. 43, pp. 483-486. Elsevier, Netherlands. ISSN 0007-8506.
Go to original source...
- MOU, J., LIU, C.R. (1995) A methodology for machine tools error correction using reference parts. In: International Journal of Computer Integrated Manufacturing, Vol. 8, pp. 64-77. Taylor & Francis, England. ISSN 0951-192X.
Go to original source...
- UMAMAHESWARA RAJU, R.S., RAMESH, R., ROHIT VARMA, K. (2020) Development of surface texture evaluation system for highly sparse data-driven machining domain. In: International Journal of Com-puter Integrated Manufacturing, Vol. 33, pp. 859-868. Taylor & Francis, England. ISSN 0951-192X.
Go to original source...
- SCHMITZ, T.L., COUEY, J., MARSH, E., MAUNTLER, N., HUGHES, D. (2007) Runout effects in milling: Surface finish, surface location error, and stability. In: International Journal of Machine Tools and Manufacture, Vol. 47, pp. 841-851. Elsevier, Netherlands. ISSN 0890-6955.
Go to original source...
- OMAR, O.E.E.K., EL-WARDANY, T., NG, E., ELBESTAWI, M.A. (2007) An improved cutting force and surface topography prediction model in end milling. In: International Journal of Machine Tools and Manu-facture, Vol. 47, pp. 1263-1275. Elsevier, Netherlands. ISSN 0890-6955.
Go to original source...
- BUJ-CORRAL, I., VIVANCOS-CALVET, J., GONZÁLEZ-ROJAS, H. (2011) Influence of feed, eccen-tricity and helix angle on topography obtained in side milling processes. In: International Journal of Machine Tools and Manufacture, Vol. 51, pp. 889-897. Elsevier, Netherlands. ISSN 0890-6955.
Go to original source...
- YANG, D., LIU, Z. (2015) Surface plastic deformation and surface topography prediction in peripheral milling with variable pitch end mill. In: International Journal of Machine Tools and Manufacture, Vol. 91, pp. 43-53. Elsevier, Netherlands. ISSN 0890-6955.
Go to original source...
- JIANG, H., LONG, X., MENG, G. (2008) Study of the correlation between surface generation and cut-ting vibrations in peripheral milling. In: Journal of Materials Processing Technology, Vol. 208, pp. 229-238. Else-vier, Netherlands. ISSN 0924-0136.
Go to original source...
- ARIZMENDI, M., CAMPA, F.J., FERNÁNDEZ, J., LOPEZ DE LACALLE, L.N., GIL, A., BILBAO, E., VEIGA, F., LAMIKIZ, A. (2009) Model for surface topography prediction in peripheral milling con-sidering tool vibration. In: CIRP Annals, Vol. 58, pp. 93-96. Elsevier, Netherlands. ISSN 0007-8506.
Go to original source...
- COSTES, J.P., MOREAU, V. (2011) Surface roughness prediction in milling based on tool displace-ments. In: Journal of Manufacturing Processes, Vol. 13, pp. 133-140. Elsevier, Netherlands. ISSN ISSN 1526-6125.
Go to original source...
- LARTIGUE, C., DUC, E., TOURNIER, C. (2019) Machining of free-form surfaces and geometrical specifications. In: Journal of Engineering Manufacture, Vol. 213, pp. 21-27. Sage Publications, United States. ISSN 0954-4054
Go to original source...
- ZHANG, C., GUO, S. (2017) Error compensation model considering tool wear in milling difficult to cut materials. In: International Journal of Computer Integrated Manufacturing, Vol. 30, pp. 822-838. Taylor & Francis, England. ISSN 0951-192X.
Go to original source...
- FAN, H.Z., CAO, Y.L., XI, G. (2020) Judging of machining feasibility and calculation of midsection for the five-axis milling of shrouded centrifugal impeller. In: Journal of Industrial and Production Engineering, Vol. 37, pp. 360-369. Taylor & Francis, England. ISSN 2168-1023.
Go to original source...
- MELKOTE, S.N., SUTHERLAND, J.W., KING, C. (1999) The Effect of Tool Flexibility on Back-Cutting in End Milled Surfaces. In: Journal of Manufacturing Science and Engineering-Transactions of the ASME, Vol. 121, pp. 532-537. ASME, USA. ISSN 1087-1357
Go to original source...
- ALTINTAS, Y., ENGIN, S. (2001) Generalized Modeling of Mechanics and Dynamics of Milling Cut-ters. In: CIRP Annals, Vol. 50, pp. 25-30. Elsevier, Netherlands. ISSN 0007-8506.
Go to original source...
- LI, S., LIU, R., ZHANG, A. (2002) Study on an end milling generation surface model and simulation tak-ing into account of the main axle's tolerance. In: Journal of Materials Processing Technoly, Vol. 129, pp. 86-90. Elsevier, Netherlands. ISSN 0924-0136.
Go to original source...
- MUÑOZ-ESCALONA, P., MAROPOULOS, P.G. (2015) A geometrical model for surface roughness prediction when face milling Al 7075-T7351 with square insert tools. In: Journal of Manufacturing Systems, Vol. 36, pp. 216-223. Elsevier, Netherlands. ISSN 0278-6125.
Go to original source...
- KUNDRÁK, J., MARKOPOULOS, A.P., MAKKAI, T., KARKALOS, N.E. (2019) Effect of Edge Ge-ometry on Cutting Forces in Face Milling with Different Feed Rates. In: Manufacturing Technology, Vol. 19, No. 6, pp. 984-992. Elsevier, Netherlands. ISSN 1213-2489.
Go to original source...
- KUNDRÁK, J., MARKOPOULOS, A.P., MAKKAI, T., DESZPOTH, I., NAGY, A. (2018) Analysis of the Effect of Feed on Chip Size Ratio and Cutting Forces in Face Milling for Various Cutting Speeds. In: Manufacturing Technology, Vol. 18, No. 3, pp. 431-438. Elsevier, Netherlands. ISSN 1213-2489.
Go to original source...
- KUNDRÁK, J., PÁLMAI, Z., KARPUSCHEWSKI, B., FELHŐ, C., MAKKAI, T., BORYSENKO, D. (2021) Force and Temperature Conditions of Face Milling with Varying Chip Quotient as a Function of Angle of Rotation. In: Manufacturing Technology, Vol. 21, No. 2, pp. 214-222. Elsevier, Netherlands. ISSN 1213-2489.
Go to original source...
- SANDİLEK, M., KOUSAL, L., NÁPRSTKOVÁ, N., SZOTKOWSKI, T., HAJNY©, J. (2018) The Analysis of Accuracy of Machined Surfaces and Surfaces Roughness after 3axis and 5 axis Milling. In: Manufacturing Technology, Vol. 18, No. 6, pp. 1015-1022. Elsevier, Netherlands. ISSN 1213-2489.
Go to original source...
- TORTA, M., ALBERTELLI, P., MONNO, M. (2020) Surface morphology prediction model for milling operations. In: International Journal of Advanced Manufacturing Technology, Vol. 106, pp. 3189-3201. Springer Verlag, Germany. ISSN 0268-3768.
Go to original source...
- CHOU, Y.-C., CHANDRU, V., BARASH, M.M. (1989) A Mathematical Approach to Automatic Config-uration of Machining Fixtures: Analysis and Synthesis. In: Transactions of ASME Journal of Manufacturing Sci-ence and Engineering, Vol. 111, pp. 299-306. ASME, USA. ISSN 1087-1357.
Go to original source...
- DEMETER, E.C. (1994) Restraint Analysis of Fixtures Which Rely on Surface Contact. In: Transactions of ASME Journal of Manufacturing Science and Engineering, Vol. 116, pp. 207-215. ASME, USA. ISSN: 1087-1357.
Go to original source...
- ASADA, H., BY, A. (1985) Kinematic analysis of workpart fixturing for flexible assembly with automati-cally reconfigurable fixtures. In: IEEE Journal of Robotic Automation, Vol. 1, pp. 86-94. IEEE, USA. ISSN 0882-4967.
Go to original source...
- SÖDERBERG, R., LINDKVIST, L. (2001) Automated Seam Variation and Stability Analysis for Auto-motive Body Design. In: Bourdet, P., Mathieu, L. (Eds). Geometric Product Specification and Verification: Inte-gration of Functionality, Dordrecht: Springer Netherlands, pp. 255-264. ISBN 978-94-017-1691-8.
Go to original source...
- VILLENEUVE, F., LEGOFF, O., BOURDET, P. (2000) Three Dimensional geometrical tolerancing in process planning. In: CIRP Journal of Manufacturing Systems, Vol. 30, pp. 20-39. Elsevier, Netherlands. ISSN 1581-5048
- BOURDET, P., CLEMENT, A. (1988) A Study of Optimal-Criteria Identification Based on the Small-Displacement Screw Model. In: CIRP Annals, Vol. 37, pp. 503-506. Elsevier, Netherlands. ISSN 0007-8506.
Go to original source...
- WEILL, R., DAREL, I., LALOUM, M. (1991) The influence of fixture positioning errors on the geomet-ric accuracy of mechanical parts. In: CIRP Conference on Production Engineering And Manufacturing Science, Tianjin, China, pp. 215-225.
- WANG, L., Li, W., Si, H., Yuan, X., Liu, Y. (2019) Geometric deviation reduction method for interpolat-ed toolpath in five-axis flank milling of the S-shaped test piece. In: Journal of Engineering Manufacture, Vol. 234, pp. 910-919. Sag Publications, United States. ISSN 0954-4054
Go to original source...
- ARMILLOTTA, A., CARRINO, L., MORONI, G., SEMERARO, Q. (2003) An analytical approach to machining deviation due to fixturing. In: Bourdet, P., Mathieu, L. (Eds), Geometric Product Specification and Verification: Integration of Functionality. Dordrecht: Springer Netherlands, pp. 175-184. ISBN 978-94-017-1691-8.
Go to original source...
- POLINI, W., MORONI, G. (2007) Position Deviation of a Holes Pattern Due to Six-Point Locating Principle. In: Davidson, J.K. (Ed). BT - Models for Computer Aided Tolerancing in Design and Manufacturing, Dordrecht: Springer Netherlands, pp. 201-211. ISBN 978-1-4020-5438-9.
Go to original source...
- MORONI, G., PETRÒ, S., POLINI, W. (2014) Robust Design of Fixture Configuration. In: Procedia CIRP, Vol. 21, pp. 189-194. Elsevier, Netherlands. ISSN 2212-8271.
Go to original source...
- CORRADO, A., POLINI, W., MORONI, G. (2016) Robust Design of a Fixture Configuration in the Presence of form Deviations. In: Procedia CIRP, Vol. 43, pp. 35-40. Elsevier, Netherlands. ISSN 2212-8271.
Go to original source...
- POLINI, W., CORRADO, A. (2019) A general model to estimate hole location deviation in drilling: the contribution of three error sources. In: International Journal of Advanced Manufacturing Technology, Vol. 102, pp. 545-557. Springer Verlag, Germany. ISSN 0268-3768.
Go to original source...
- CORRADO, A., POLINI, W. (2017) Manufacturing signature in jacobian and torsor models for tolerance analysis of rigid parts. In: Robotic and Computer-Integrated Manufacturing, Vol. 46, pp. 15-24. Elsevier, Nether-lands. ISSN 0736-5845.
Go to original source...
- CORRADO, A., POLINI, W. (2017) Manufacturing signature in variational and vector-loop models for tolerance analysis of rigid parts. In: International Journal of Advanced Manufacturing Technology, Vol. 88, pp. 2153-2161. Springer Verlag, Germany. ISSN 0268-3768.
Go to original source...
- POLINI, W., CORRADO, A. (2016) Geometric tolerance analysis through Jacobian model for rigid as-semblies with traslational deviations. In: Assembly Automation, Vol. 36, No. 1, pp. 72-79. Emerald Insight, Great Britain. ISSN : 0144-5154
Go to original source...
- KAZAR, B.M., CELIK, M. (Eds), (2012) Spatial AutoRegression (SAR) Model. Boston, MA: Springer. ISBN 978-1-4614-1842-9.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.