Manufacturing Technology 2021, 21(6):805-817 | DOI: 10.21062/mft.2021.088

The use of quality tools to reduce surface defects of painted steel structures

Krzysztof Knop ORCID...
Faculty of Management, Czestochowa University of Technology. Armii Krajowej 19B, 42-200 Czestochowa. Poland

The article presents the results of the use of quality instruments – tools and techniques – in order to reduce surface defects of steel structures on the example of a selected element – engine cover of asphalt milling machines. The article shows the potential of using selected quality tools – basic and new – in the service of quality analysis and improvement. Quantitative analyzes were presented out using the Pareto-Lorenz diagram and the c control chart, qualitative analyzes using the Ishikawa diagram and the FMEA method, quantitative & qualitative analyzes using the interrelationship diagram and matrix diagram, and it was proposed quality improvement using qualitative tools such as affinity diagram, and PDPC diagram. The most common defects of painted surfaces turned out to be improper thickness and surface contamination. As it has been shown, the experience of employees is largely responsible for the cause of these defects, which was also confirmed by other analyses carried out with the use of quality tools. The training was the most frequent method of prevention. It has also been shown that special attention should be paid to quality control, its effectiveness, and quantity. The article proves that correctly used quality tools can contribute to the improvement of the quality of manufactured products, helps in solving various quality problems.

Keywords: defects of painted surfaces, steel structures, quality tools, improvement

Received: July 16, 2021; Revised: November 25, 2021; Accepted: December 1, 2021; Prepublished online: December 21, 2021; Published: January 8, 2022  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Knop K. The use of quality tools to reduce surface defects of painted steel structures. Manufacturing Technology. 2021;21(6):805-817. doi: 10.21062/mft.2021.088.
Download citation

References

  1. ISO 9000:2015. Quality management systems - Fundamentals and vocabulary.
  2. GYGI, C., GUSTAFSON, T., WILLIAMS, B. (2006). Six Sigma Workbook for Dummies. Hoboken, NJ (USA): Wiley Publishing, Inc. ISBN-10: 0-470-04519-1.
  3. TAGUE, N. R. (2005). The Quality Toolbox (2nd ed.). Milwaukee, Wisconsin: ASQ Quality Press. ISBN 978-1-62198-045-2.
  4. ULEWICZ, R. (2014). Practical Application of Quality Tools in the Cast Iron Foundry. In: Manufacturing Technology, Vol. 14, No. 1, pp. 104 - 111. ISSN 1213-2489. Go to original source...
  5. FONSECA, L., LIMA, V., SILVA, M. (2015). Utilization of quality tools: Does sector and size matter? In: International Journal for Quality Research, Vol. 9, No. 4, pp. 605 - 620. ISSN 1800-6450.
  6. RAKHMANIAR, M., RAHMANIA, I.M., SETYANINGSIH, S., BASRI, M.H. (2012). Application of Quality Tools and Techniques in Hospital: Case Study in Bandung Indonesia. In: 3rd International Research Symposium in Service Management, July 3-7, 2012, Beijing.
  7. HADIMAN, N., HUMIRAS, H. P. (2017). Aplication of quality control tools to reducing defect product in a surfactant and chemicals industry. In: International Journal of Modern Trends in Engineering and Research (IJMTER), Vol. 04, Iss. 12, pp. 261 - 271. e-ISSN 2349-9745. Go to original source...
  8. SANNY, L., AMALIA, R. (2015). Quality improvement strategy to defect reduction with seven tools method: Case in food field company in Indonesia. In: International Business Management, No. 9, pp. 445 - 451. ISSN 1993-5250.
  9. MEMON, I.A., JAMALI, Q.B., JAMALI, A.S., ABBASI, M., JAMALI, N., JAMALI, Z. (2019). Defect Re-duction with the Use of Seven Quality Control Tools for Productivity Improvement at an Automobile Company. In: Engineering, Technology & Applied Science Research, Vol. 9, No. 2, pp. 4044 - 4047. eISSN 1792-8036. Go to original source...
  10. LIANG, K. (2010). Aspects of Quality Tools on Total Quality Management. In: Modern Applied Science, Vol. 4, No. 9, pp. 66 - 74. e-ISSN 1913-1852. Go to original source...
  11. SOUSA, S., RODRIGUES, N., NUNES, E. (2017). Application of SPC and quality tools for process im-provement. In: Procedia Manufacturing, Vol. 11, pp. 1215 - 1222. ISSN 2351-9789. Go to original source...
  12. TARÍ, J., SABATER, V. (2004). Quality tools and techniques: Are they necessary for quality management? In: International Journal of Production Economics, Vol. 92, No. 3, pp. 267 - 280. ISSN: 0925-5273. Go to original source...
  13. MCQUATER, R.E., SCURR, C.H., DALE, B.G., HILLMAN, P.G. (1995). Using quality tools and tech-niques successfully. In: The TQM Magazine, Vol. 7, No. 6, pp. 37 - 42. ISSN 0954-478X. Go to original source...
  14. VIJAYARANGAN, J., SAMY, M. A., BHARATHIRAJA, G., RAGUL, G. & SHERIFF F. M. (2017). Im-plementation of seven tools of quality in educational arena: A case study. In: International Journal of Mechani-cal Engineering and Technology (IJMET), Vol. 8, Iss. 8, pp. 882 - 891. e-ISSN 0976-6359.
  15. PAVLETIC, D., SOKOVIC, M., PALISKA, G. (2008). Practical Application of Quality Tools. In: Interna-tional Journal for Quality Research, Vol. 2, No. 3, pp. 199 - 205. e-ISSN: 1800-7473.
  16. PACANA, A., CZERWIÑSKA, K. (2020). Improving the quality level in the automotive industry. In: Pro-duction Engineering Archives, Vol. 26, Iss. 4, pp. 162 - 166. e-ISSN 2353-7779. Go to original source...
  17. BAMFORD, D. R., GREATBANKS, R. W. (2005). The use of quality management tools and techniques: a study of application in everyday situations. In: International Journal of Quality & Reliability Management, Vol. 22, No. 4, pp. 376 - 392. ISSN 0265-671X. Go to original source...
  18. DIAS, S., SARAIVA, P.M. (2004). Use basic quality tools to manage your processes. In: Quality Progress, Vol. 37, pp. 47 - 53. ISSN 0033-524X.
  19. ABDEL-HAMID, M., ABDELHALEEM, H. (2019). Improving the Construction Industry Quality Using the Seven Basic Quality Control Tools. In: Journal of Minerals and Materials Characterization and Engineerin, Vol. 7, No. 6, pp. 412 - 420. e-ISSN 2327-4085. Go to original source...
  20. ANDRÁSSYOVÁ, Z., ®ARNOVSKÝ, J., ÁLLÓ, ©., HRUBEC, J. (2013). Seven New Quality Manage-ment Tools. In: Advanced Materials Research, Vol. 801, pp. 25 - 33. ISSN: 1662-8985. Go to original source...
  21. MIZUNO, S. (1988). Management for Quality Improvement: The 7 New QC Tools. Woodland Hills, CA (USA): Productivity Pr. Inc. ISBN 10: 0915299291.
  22. NAYATANI, Y., EIGA, T., FUTAMI, R. (2006). The seven QC tools: New tools for a new era. In: Envi-ronmental Quality Management, Vol. 4, No. 1, pp. 101 - 109. ISSN 15206483. Go to original source...
  23. DAMAYANTI, R., SUBAGYO, B., WIJAYA, A., HARTONO, B. (2019). Seven Management and Planning Tools in Megaproject Management: A Literature Review. IOP Conference Series: Materials Science and Engineer-ing, 598, 012014. Go to original source...
  24. SIWIEC, D., PACANA, A. (2021). Method of improve the level of product quality. In: Production Engineering Archives, Vol. 27, Iss. 1, pp. 1 - 7. e-ISSN 2353-7779. Go to original source...
  25. HAGEMEYER, C., GERSHENSON, J.K. JOHNSON, D.M. (2006). Classification and application of problem solving quality tools: A manufacturing case study. In: The TQM Magazine, Vol. 18, No. 5, pp. 455 - 483. ISSN 0954-478X. Go to original source...
  26. KARDAS, E. (2017). The Analysis of Non-Conformances of Products in Plate Mill Using Selected Quality Tools. In: 26th International Conference on Metallurgy and Materials (METAL 2017), Tanger, Ostrava. ISBN 978-80-87294-79-6.
  27. KNOP, K. (2018). Statistical control of the production process of rolled products. In: Production Engineering Archives, Vol. 20, pp. 26 - 31. ISSN 2353-5156. Go to original source...
  28. KNOP, K. (2021). Managing and Improving the Drilling Process of Woodwork Furniture with the Use of SPC Tools. In: Manufacturing Technology, Vol. 21, Iss. 4, e-ISSN 2787-9402. Go to original source...
  29. GODINA, R., MATIAS, J., AZEVEDO, S. (2016). Quality improvement with Statistical Process Control in the automotive industry. In: International Journal of Industrial Engineering and Management, Vol. 7, No. 1, pp. 1 - 8. ISSN 2217-2661. Go to original source...
  30. MONTGOMERY, D.C. (2012). Statistical Quality Control, 7th Edition. Hoboken, NJ (USA): Wiley. ISBN: 978-1-118-14681-1.
  31. DZIUBA, SZ. T., INAGALDI, M., KOZINA, A., HERNES, M. (2021). Using the FMEA Method as a Response to a Customer Complaint: a Case Study. In: Revista Gestao & Tecnologia-Journal of Management and Technology, Vol. 21, No. 1, pp. 73 - 88. e-ISSN: 2177-6652. Go to original source...
  32. KAPUSTKA, K., ZIEGMANN, G., KLIMECKA-TATAR, D., SARA NAKONCZY, S. (2020). Process management and technological challenges in the aspect of pernament magnets recycling - the second life of neodymium magnets. In: Manufacturing Technology, Vol. 20, Iss. 5, pp. 617 - 624. e-ISSN 2787-9402. Go to original source...
  33. KRYNKE, M., MIELCZAREK, K., KIRILIUK, O. (2021). Cost Optimization and Risk Minimization dur-ing Teamwork Organization. In: Management Systems in Production Engineering, Vol. 29, Iss. 2, pp. 145 - 150. e-ISSN 2450-5781. Go to original source...
  34. CZAJKOWSKA, A., INGADLI, M. (2021). Application of Servqual and Servperf methods to assess the quality of teaching services - comparative analysis. In: Manufacturing Technology, Vol. 21, Iss. 3, pp. 294 - 305. e-ISSN 2787-9402. Go to original source...
  35. INGALDI, M. (2021). Assessment of the Service Provision Process as a Business Process Management Tool. In: Polish Journal of Management Studies, Vol. 23, No. 1, pp. 204 - 223. ISSN 20817452. Go to original source...
  36. KNOP, K., ULEWICZ, R. (2019). Assessment of technology, technological resources and quality in the manufacturing of timber products. In: 12th WoodEMA Annual International Scientific Conference on Digitalisation and Circular Economy: Forestry and Forestry Based Industry Implications, pp. 251 - 256. USB & WoodEMA, Sofia, Bulgaria. ISBN 978-954-397-042-1.
  37. KNOP, K. (2020). Indicating and Analysis the Interrelation Between Terms - Visual: Management, Control, Inspection and Testing, In: Production Engineering Archives, Vol. 26, Iss. 3, pp. 110 - 120. e-ISSN 2353-7779. Go to original source...
  38. ULEWICZ, R., KLESZCZ, D., ULEWICZ, M. (2021). Implementation of Lean Instruments in Ceramics Industries, In: Management Systems in Production Engineering, Vol. 29, Iss. 2, pp. 203 - 207. e-ISSN 2450-5781. Go to original source...
  39. PENDOKHARE, D. G., QUAZI, T., KULKARNI, P. S. (2015). Redesign and Manufacturing by using DMADV Method. In: International Journal of Research in Engineering and Technology, Vol. 4, No. 2, pp. 144 - 149. eISSN: 2319-1163. Go to original source...
  40. KLIMECKA-TATAR, D., INGALDI, M., OBRECHT, M. (2021). Sustainable Development in Logistic - a Strategy for Management in Terms of Green Transport. In: Management Systems in Production Engineering, Vol. 29, Iss. 2, pp. 91 - 96. e-ISSN 2450-5781. Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.