Manufacturing Technology 2022, 22(3):377-383 | DOI: 10.21062/mft.2022.035
Research on Grinding Parameters of Parts with Same Clamping Mode and Different Sizes
- 1 School of Electrical and Electronic Engineering, Chongqing Vocational and Technical University of Mechatronics, Chongqing, China
- 2 School of Mechanical Engineering, Xi’an Jiaotong University, 28 Xianning Road, Xi’an, Shaanxi 710049, P.R. China
Aiming to study the influence of ultra-precision grinding parameters on the accuracy between the same clamping method and different workpiece sizes. This paper mainly analyzes the difference between the measurement precision of different parts by the same measurement method and the measurement precision of the same parts by different measurement methods. Therefore, the influence of grinding parameters on grinding precision is reflected. For the same part, it is concluded that the coaxiality error coincidence degree at end A and end B reaches 90.32% and 95.27%, respectively by using precision three-coordinate measuring instrument and Mahr roundness instrument. The coincidence degree of end A and end B verticality error reached 97.54% and 91.08%, respectively. For parts with different sizes, the Mahr roundness meter is used for measurement. The analysis shows that the coaxiality coincidence at end A and end B is the highest, reaching 98.36% and 92%, respectively. And from the analysis, the errors are mainly reflected in the factors such as jig and fixture and grinding process.
Keywords: Ultra-precision, ultra-high speed grinding; Grinding parameters; Optimization; Precision error
Grants and funding:
This research was funded by the Chongqing Education Commission Science and Technology Research Project(KJZD-K201903701) and (KJQN201803703) and the Chongqing Higher Education Teaching Reform Research Project (193463)
Received: March 20, 2022; Revised: June 7, 2022; Accepted: June 9, 2022; Prepublished online: June 9, 2022; Published: July 1, 2022 Show citation
References
- Chang Z, Hu L. (2021). Study on scatter of surface integrity of bearing raceway grinding[J]. Manufacturing Technology, 21(6):781-787.
Go to original source...
- Tawakoli T., Hadad M. J., Sadeghi M. H. (2009). An experimental investigation of the effects of workpiece and grinding parameters on minimum quantity lubrication-MQL grinding[J]. International Journal of Machine Tools & Manufacture, 49(12-13):924-932.
Go to original source...
- Padda A. S., Kumar S., Mahajan A. (2015). Effect of Varying Surface Grinding Parameters on the Surface Roughness of Stainless Steel[J]. Carbon, 100: 0.08.
- Vishal Francis, Abhishek khalkho, Jagdeep Tirkey, Rohit Silas Tigga & Neelam Anmol Tirkey. (2014). Experimental Investigation And Prediction Of Surface Roughness In Surface Grinding Operation Using Factorial Method And Regression Analysis [J].International Journal of Mechanical Engineering And Technology (IJMET), Volume 5, Issue 5, May, pp. 108-114.
- Adibi H., Rezaei S. M., Sarhan A. A. D. (2013). Analytical modelling of grinding wheel loading phenome-na[J]. The International Journal of Advanced Manufacturing Technology, 68(1-4): 473-485.
Go to original source...
- Jagtap K. R., Ubale S. B., Kadam M. S. (2011). Optimisation of cylindrical grinding process parameters for AISI 5120 steel using Taguchi method [J]. International Journal of Design and Manufacturing Technology, 2(1): 47-56.
Go to original source...
- Alagumurthi N., Palaniradja K., Soundararajan V. (2007). Heat generation and heat transfer in cylindrical grinding process -a numerical study [J]. International Journal of Advanced Manufacturing Technology, 34(5-6):474-482.
Go to original source...
- Lan S., Jiao F. (2019). Modeling of heat source in grinding zone and numerical simulation for grinding temperature field [J]. International Journal of Advanced Manufacturing Technology, 103(15).
Go to original source...
- Khramenkov M, Jersák J. (2021). Effect of the dressing process on the surface roughness in cylindrical grinding of Ti6Al4V alloy using stationary diamond dressing tools [J]. Manufacturing Technology, 21(5):640-646.
Go to original source...
- Farský J, Zetek M, Bakša T, Kubátová D, Hu Y. (2020). Effect of the cutting conditions on surface roughness during 5-axis grinding of Maraging steel MS1 [J]. Manufacturing Technology, 20(1).
Go to original source...
- Salonitis K., Chondros T., Chryssolouris G. (2008). Grinding wheel effect in the grind-hardening process [J]. The International Journal of Advanced Manufacturing Technology, 38(1-2): 48-58.
Go to original source...
- Yu X. (2011). Finite element analysis of influence of grinding parameters on grinding force[C]// International Conference on Electronic & Mechanical Engineering & Information Technology. IEEE.
- Li L., Chen B., Chen B. (2015). Multi-objective optimization of cutting parameters in sculptured parts ma-chining based on the neural network [J]. Journal of Intelligent Manufacturing, 26(5):1-8.
Go to original source...
- Mayer J. E., Fang G. P. (1995). Effect of Grinding Parameters on Surface Finish of Ground Ceramics [J]. CIRP Annals - Manufacturing Technology, 44(1):279-282.
Go to original source...
- Beyer H. G. (1999). The simple genetic algorithm: foundations and theory [M]. 1999.
- Tang L., Yuan S., Tang Y. (2019). Optimization of impulse water turbine based on GA-BP neural network arithmetic [J]. Journal of Mechanical Science and Technology, 33(1):241-253.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.