Manufacturing Technology 2022, 22(3):367-376 | DOI: 10.21062/mft.2022.038
Theoretical and Experimental Study on the Influence of Ultrasonic Vibration on Contact Friction
- School of Electronic Engineering and Intelligent Manufacturing, Anqing Normal University, Anqing, Anhui, China
The effects of punch radius, deep-drawing speed and amplitude on the friction coefficient were studied on an improved drawing-bulging friction coefficient testing device on basis of ultrasonic vibration. A contact friction model based on the tribology theory of adhesion and plowing was constructed and used to explain the friction reduction phenomenon of applied out-of-plane normal vibration. The results show that the friction coefficient decreases with the increase of ultrasonic vibration amplitude. At the same deep-drawing height, the friction coefficient decreasing rates at amplitude of 7.8um and 10.1 um on the deep-drawing speed of 0.1 mm/s and 10 mm/s, were 6.7% and 18.8%, respectively. the friction coefficients at the punch radii R0.3 and R1.5 declined from 0.18 to 0.13 and from 0.12 to 0.11. The friction coefficients of thin specimens were larger than thick specimens whether ultrasonic vibration was applied or not. The average friction coefficient from theoretical modeling (μ_v) was smaller than the friction coefficient without ultrasonic vibration (μ_0), and the relative friction coefficient ratio declined with the rise of amplitude and was inversely proportional to time.
Keywords: Ultrasonic vibration, Friction coefficient, Surface effect, Drawing-bulgin, surface morphology
Grants and funding:
The authors gratefully acknowledge the supports of the Natural Science Foundation of the Educational Commission of Anhui Province of China (Grant No. KJ2019A0576) and the project of the open competition mechanism to select the best candidates (Grant No. 220015)
Received: June 15, 2021; Revised: June 19, 2022; Accepted: June 20, 2022; Prepublished online: June 22, 2022; Published: July 1, 2022 Show citation
References
- LI Z., YANG D., HAO W.,et al. (2016). A novel technique for micro-hole forming on skull with the assistance of ultrasonic vibration. Journal of the Mechanical Behavior of Biomedical Materials, 57: 1-13.
Go to original source...
- KRIECHENBAUER S., MAUERMANN R., MULLER P. (2014). Deep Drawing with Superimposed Low-frequency Vibrations on Servo-screw Presses. Procedia Engineering, 81: 905-913.
Go to original source...
- Řiháček J, Podaný K, Faltýnek F. (2019). Prediction of the Stamped Part Thinning Depending on Its Geometry and Blank Material. Manufacturing Technology, 19: 314-320.
Go to original source...
- LIU S., SHAN X., GUO K., et al. (2018). Experimental study on titanium wire drawing with ultrasonic vibration. Ultrasonics, 83: 60-67.
Go to original source...
- Michna ©, Hren I, Cais J, et al. (2020). The Research of the Different Properties and Production Parameters having Influence on Deep-Drawing Sheets made of AlMg3 Alloy. Manufacturing Technology, 20: 347-354.
Go to original source...
- LIU Y., SUSLOV S., HAN Q., et al. (2013). Comparison Between Ultrasonic Vibration-Assisted Upsetting and Conventional Upsetting. Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science, 3232: 1-13.
Go to original source...
- RASOLI M.A., ABDULLAH A., FARZIN M., et al. (2012). Influence of ultrasonic vibrations on tube spinning process. Journal of Materials Processing Technology, 212: 1443-1452.
Go to original source...
- TAN R., ZHAO X., GUO S., et al. (2020). Sustainable production of dry-ultra-precision machining of Ti-6Al-4V alloy using PCD tool under ultrasonic elliptical vibration-assisted cutting. Journal of Cleaner Production, 248: 1-44.
Go to original source...
- ZHU L., NI C., YANG Z., et al. (2019). Investigations of micro-textured surface generation mechanism and tribological properties in ultrasonic vibration-assisted milling of Ti-6Al-4V. Precision Engineering, 57: 229-243.
Go to original source...
- GUNDUZ I.E., MCCLAIN M., CATTANI P., et al. (2018). 3D printing of extremely viscous materials using ultrasonic vibrations. Additive Manufacturing, 22: 98-103.
Go to original source...
- SIEGERT K., ULMER J. (2001). Influencing the Friction in Metal Forming Processes by Superimposing Ultrasonic Waves. Cirp Annals-Manufacturing Technology, 50: 195-200.
Go to original source...
- BUNGET C., NGAILE G. (2011). Influence of ultrasonic vibration on micro-extrusion. Ultrasonics, 51: 606-616.
Go to original source...
- YAO Z., KIM G.Y., FAIDLEY L., et al. (2012). Effects of superimposed high-frequency vibration on deformation of aluminum in micro/mesoscale upsetting. Journal of Materials Processing Technology, 212: 640-646.
Go to original source...
- HUNG J.C., HUANG C.C. (2012). Evaluation of friction in ultrasonic vibration-assisted press forging using double cup extrusion tests. International Journal of Precision Engineering and Manufacturing, 13: 2103-2108.
Go to original source...
- TSAI C.C., TSENG C.H. (2006). The effect of friction reduction in the presence of in-plane vibrations. Archive of Applied Mechanics, 75: 164-176.
Go to original source...
- POPOV M., POPOV V.L., POPOV N.V. (2017). Reduction of friction by normal oscillations. I. Influence of contact stiffness. Friction,5: 45-55.
Go to original source...
- MAO X., POPOV V.L., STARCEVIC J., et al. (2017). Reduction of friction by normal oscillations. II. In-plane system dynamics. Friction, 5: 194-206.
Go to original source...
- POPOV M. (2016). Critical velocity of controllability of sliding friction by normal oscillations in viscoelastic contacts. Mechanical Engineering, 14: 335-341.
Go to original source...
- POPOV V.L., POHRT R., HESS M. (2016). General procedure for solution of contact problems under dynamic normal and tangential loading based on the known solution of normal contact problem. Journal of Strain Analysis for Engineering Design, 51: 1-9.
Go to original source...
- TEIDELT E., WILLERT E., FILIPPOV A.E., et al.L (2012). Modeling of the dynamic contact in stick-slip microdrives using the method of reduction of dimensionality. Physical Mesomechanics, 15: 287-292.
Go to original source...
- WANG W., WAGONER R.H., WANG X.J. (1996). Measurement of friction under sheet forming conditions. Metallurgical and Materials Transactions A-Physical Metallurgy and Materials Science, 27: 3971-3981.
Go to original source...
- ZHA C.L., CHEN W. (2019). Theories and experiments on effects of acoustic energy field in micro-square cup drawing. International Journal of Advanced Manufacturing Technology, 104: 4791-4802.
Go to original source...
- ARCHIE H., WILLIAM B.S. (1949). Engineering mechanics, New York, Prentice-Hall, Inc 249: 0-505.
- HU J., SHIMIZU T., YANG M. (2018). Investigation on ultrasonic volume effects: Stress superposition, acoustic softening and dynamic impact. Ultrasonics Sonochemistry, 48: 240-248.
Go to original source...
- WANG C.J., LIU Y., GUO B., et al. (2016). Acoustic softening and stress superposition in ultrasonic vibration assisted uniaxial tension of copper foil: experiments and modeling. Materials and Design, 112: 246-253.
Go to original source...
- BOWDEN F.P., TABOR D.F. (1964). The friction and Lubrication of Solids. Wear ,7: 557-558.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.