Manufacturing Technology 2022, 22(6):693-702 | DOI: 10.21062/mft.2022.076
Microscopic Analysis of the Surface Morphology of Multilayer Structures of the AluminumAlloy – Silicon Type after Water Jet Cutting
- 1 Lublin University of Technology, Faculty of Mechanical Engineering, Department of Production Engineering, 20-618 Lublin, ul. Nadbystrzycka 36, Poland
- 2 University of Salerno, Department of Industrial Engineering, (Bio) Tribology, Applied Mechanics Noise and Vibration Control, National Coordinator AIMETA Tribology Group- GAIT, Via Giovanni Paolo II, 132 - 84084 Fisciano (SA) Italy
The paper presents the results of an experimental work on the assessment of microscopic morphology of the surfaces obtained as a result of cutting with a Water Jet (WJ) water abrasive beam. The examination of microscopic structures was carried out with the use of Nova NanoSem 450 scanning electron micro-scope. The subject of analysis were the interfacial structures of multilayer structures connected in a vul-canization process with the surface of thin-walled parts made of AW-5754 aluminum alloy. The results of the research were compiled as a function of the technological WJ cutting conditions, such as feedrate and abrasive material flow.
Keywords: Aluminum alloy, Microscopic analysis, Water Jet cutting, Surface morphology
Grants and funding:
The project/research was financed in the framework of the project Lublin University of Technology - Regional Excellence Initiative, funded by the Polish Ministry of Science and Higher Education (contract no. 030/RID/2018/19)
Received: September 13, 2022; Revised: November 27, 2022; Accepted: December 6, 2022; Prepublished online: December 9, 2022; Published: January 6, 2023 Show citation
ACS | AIP | APA | ASA | Harvard | Chicago | IEEE | ISO690 | MLA | NLM | Turabian | Vancouver |
References
- HAJJARI E., DIVANDARI M., MIRHABIBI A.R. (2010). The effect of applied pressure on fracture surface and tensile properties of nickel coated continuous carbon fiber reinforced aluminum composites fabricated by squeeze casting. Materials and Design, Vol. 31, pp. 2381-2386. ISSN 0261-3069
Go to original source...
- MÜLLER, M., KOLÁŘ V., AND VALÁ©EK P. (2019) Effect of Waterjet Machining Parameters on Cut Quality of Polymeric Composite Materials Based on Biological Reinforcement in Form of Cotton Post-harvest Line Residues. Manufacturing Technology Vol. 19, no. 4 pp. 647-54.
Go to original source...
- LALET G., MIYAZAKI T., KAWASAKI A., SILVAIN J.F. (2014). Thermomechanical stability of a carbon fiber-reinforced aluminum matrix composite fabricated by spark plasma sintering in various pulse conditions. Materials Letters, Vol. 130, pp. 32-35. ISSN 0167-577X
Go to original source...
- VA©INA M, HRU®ÍK L, BUREČEK A. Study of Factors Affecting Vibration Damping Properties of Multilayer Composite Structures. Manufacturing Technology. 2020 pp.104-109.
Go to original source...
- SHIRVANIMOGHADDAM K., HAMIM S. U., KARBALAEI AKBARI M., MOUSA S. (2017). Carbon fiber reinforced metal matrix composites: fabrication processes and properties. Composites Part A: Applied Science and Manufacturing, Vol. 92, pp. 70-96. ISSN 1359-835X,
Go to original source...
- MULLER, M., D´ARMATO, R., RUDAWSKA A. (2017). Machining of polymeric composite by means of abrasive water-jet technology. In: 16th International Scientific Conference Engineering for Rural Development. pp. 121 - 127. Jelgava, Latvia University of Agriculture,
Go to original source...
- MÜLLER, M., VALÁ©EK, P., KOLÁŘ, V. (2018). Research on application of technology using water jet on machining of polymeric composite biological-reinforced materials. In: Manufacturing Technology. pp. 647-654, vol. 18, no. 4,.
Go to original source...
- GONG N.N, WANG B.W., WANG Y.H., LI X.P., W.C. LIN, FU S.H. (2020). Effect of metal surface state on injection joining strength of aluminum-rubber composite. Journal of Manufacturing Processes, pp. 365-372, Vol. 49. ISSN 1526-6125
Go to original source...
- NOVAK, M. Surface quality of hardened steels after grinding. Manufacturing Technology, 2011, Vol. XI, no. 11. pp. 55 - 59. ISSN 1213-2489.
Go to original source...
- SU Y.Y., SHEMENSKI R.M. (2001). A method for continuous monitoring of bond formation between rubber and reinforced wire. International Journal of Adhesion and Adhesives. Vol. 21, pp. 481-485. ISSN 0143-7496.
Go to original source...
- YAN H., ZHANG W.-J., JIANG H.Y., CHEN L., (2014) Energy dissipation of a ring-like metal rubber isolator. Chinese Physics. B. Vol. 23,
Go to original source...
- PICARD L., PHALIP P., FLEURY E., (2015). Ganachaud Chemical adhesion of silicone elastomers on primed metal surfaces: a comprehensive survey of open and patent literatures. Progress in Organic Coatings, pp. 120-141, Vol. 80. ISSN 0300-9440.
Go to original source...
- HASHISH, MOHAMED. (2008). Optimalization Factors in Abrasive Waterjet Machining, Journal of Engineering for Industry, Vol 113, pp. 29. ASME 1992.
Go to original source...
- ZENKIEWICZ M. (2000). Adhezja i modyfikowanie warstwy wierzchniej tworzyw wielkocz±steczkowych. WNT, Warsawa. ISBN:83-204-2547-6
- CHAO, J. AND ZHOU, G. AND LEU, M. C. AND GESKIN, E. (1955) Characteristic of Abrasive Waterjet Generated Surfaces and Effects of Cutting Parameters and Structure Vibration. Journal of Engineering for Industry. Vol 117, pp. 516-525. ISSN = 0022-0817.
Go to original source...
- BIEJOVÁ. (2013). Abrasive kind and granularity changes affects to water jet technology head vibration during cutting HARDOX material thickness alternation process. In: Applied Mechanics and Materials. vol. 308, pp. 75-79. - ISSN 1660-9336.
Go to original source...
- SÝKOROVá, L., Malachová, M. (2012). Laser Machining and Temperature Field Simulation Using COSMOS /M Software. Manufacturing Technology. No. 12. pp. 113-117 ISSN 12132489.
- ČIERNA, H., «AVODOVÁ, M. (2013). Using the design of experiment method to evaluate quality of cuts after cutting aluminum alloy by AWJ. In: Manufacturing technology: journal for science, research and production. vol. 13, pp. 303-307 no. 3.
Go to original source...
- PEREC, A., «AVODOVÁ, M. (2016). Abrasive Water Jet Cutting Depth Optimization by Taguchi Approach. Manufacturing Technology, vol. 16, p. 585-590. iss. 3,
Go to original source...
- SHARMA, V., CHATTOPADHYAYA, S. A., HLOCH, S. (2011). Multi response optimization of process parameters based on Taguchi-Fuzzy model for coal cutting by water jet technology. In: The International Journal of Advanced Manufacturing Technology, vol. 56, no. 9-12, pp. 1019-1025
Go to original source...
- PEREC, A., KAUFELD, M, PUDE, F., WEGENER, K. (2014). Taguchi Approach Optimization of Steel Surface Roughness in Abrasive Water Jet Cutting. International Conference on Mechanical Engineering and Mechatronics. Slovakia.
- NAPRSTKOVA, N., KALINCOVA, D. (2015). Influence of additional chemical components on machining properties of selected alumunium-silicon alloy. In: 14th International Scientific conference: Engineering for Rural Development. Vol. 14, pp. 766-771. Jelgava, Latvia University of Agriculture,.
- RAJ, P., HLOCH, S., TRIPATHI, R.,SRIVASTAVA, M., NAG, A., KLICHOVÁ, D.,KLICH, J., HROMASOVÁ, M., MÜLLER, M.,LINDA, M., CHATTOPADHYAYA, S., ADAMCIK, P. (2019). Investigation of sandstone erosion by continuous and pulsed water jets. In: Journal of Manufacturing Processes, vol. 42, pp. 121-130. ISSN 1526-6125.
Go to original source...
- OSTAPIUK M. (2020). Corrosion resistance of PEO and primer coatings on magnesium alloy. Journal of Asian Ceramic Societies, Vol. 9 pp 40-52, Issue 1 Article 1249.
Go to original source...
- KUTENEVA S.V., GLADKOVSKY S.V., VICHUZHANIN D.I., NEDZVETSKY P.D. (2022) Microstructure and properties of layered metal/rubber composites subjected to cyclic and impact loading. Composite Structures. Vol. 285. pp. 115078. ISSN 0263-8223.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.