Manufacturing Technology 2022, 22(6):660-668 | DOI: 10.21062/mft.2022.077

Tools for Advanced Control Processes in Plastic Injection Moulding Technology

Eliąka Cézová ORCID...
Department of Designing and Machine Components, Faculty of Mechanical Engineering, Czech Technical University in Prague, Technická 4, 166 07 Prague 6, Czech Republic

This paper describes some tools usable for quality control in plastic injection moulding. The introductory part presents tools for quality management, the use of which is demonstrated in the next part using a practical example. The selection of suitable methods was based on proven methods for quality management. They were selected to work in synergy. The author's contribution is the modification of the PDCAI method, which was enriched by another step, namely, innovation. The last part of the article presents is a demonstration of FMEA, Ishikawa diagram, and Pareto diagram.

Keywords: Quality control, Control processes, Injection moulding, Plastic technology, Pareto diagram, Ishikawa diagram, PDCAI, FMEA
Grants and funding:


This work was partly funded by the Czech Ministry of Education under the Institutional support for the development of the research organization No.: RVO12000 for Faculty of Mechanical Engineering of the Czech Technical University in Prague.

Received: January 31, 2022; Revised: November 6, 2022; Accepted: December 7, 2022; Prepublished online: December 9, 2022; Published: January 6, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Cézová E. Tools for Advanced Control Processes in Plastic Injection Moulding Technology. Manufacturing Technology. 2022;22(6):660-668. doi: 10.21062/mft.2022.077.
Download citation

References

  1. CÉZOVÁ E. (2008). Economic-statistic design control chart, Request 08, CQR VUT Brno, ISBN 978-80-214-3774-6
  2. CÉZOVÁ E., DOHNAL G. (2012). Economical and statistical optimization of control chart, Robust 2012, ISSN 1210-8022, pp. 141 - 151, 2012
  3. GOODSHIP, V. (2004). Practical Guide to Injection Moulding, Rapra Technology Limited and ARBURG Limited ISBN 1-85957-444-0
  4. CÉZOVÁ, E. (2021). On the appropriate preparation and realization of production process quality attribute measurement. (World Symposium on Mechanical - Materials Engineering & Science 9-11 September, pp.1-9, in https://iopscience.iop.org/article/10.1088/1757-899X/1190/1/012035) Go to original source...
  5. BHARTI, P.K., KHAN, M.I. Recent Methods for Optimization of Plastic Injection Moulding Process - a Retrospective and Literature Review. International Journal of Engineering Science and Technology Vol. 2(9), 2010, 4540-4554
  6. SAPUTRA, T.M. et al Quality improvement of moulding machine through statistical process control in plastic industry. Journal of Applied Research on Industrial Engineering Vol. 6, No. 2 (2019) 87-96
  7. CÉZOVÁ E. Quality control management for plastic injection moulding production, Experimental and Calculation methods, EVM 2021, Ústí nad Labem, ISBN 978-80-7561-316-5, pp. 61-67
  8. SVOBODA, M., SOUKUP, J., SAPIETA, M.: Improving the quality of cutting flat glass. in MATEC Web of Conferences157, 04004 (2018) https://doi.org/10.1051/matecconf/201815704004 Go to original source...
  9. CÉZOVÁ, E., LOPOT, F., MACHAČ, M., KAMENICKÝ, J.: Experimental measurements on a stand for a grain sampler, In: Manufacturing Technology, DOI: 10.21062/mft.2022.047 Go to original source...
  10. VONDRÁ©EK, D., HADRABA, D., MATĚJKA, R., LOPOT, F., SVOBODA, M., JELEN, K.: Uniaxial Tensile Testing Device for Measuring Mechanical Properties of Biological Tissue with Stress-Relaxation Test under a Confocal Microscope, In: Manufacturing Technology, Vol.18, No. 5 (2018) pp. 866-872, ISSN: 1213-2489 Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.