Manufacturing Technology 2023, 23(1):110-117 | DOI: 10.21062/mft.2023.003
Evaluation of Selected Technological Parameters for Selective Laser Melting of AlSi10Mg Metal Powder
- Faculty of Mechanical Engineering, University of Zilina, Univerzitna 8215/1, 010 26 ®ilina, Slovakia
Reusing the powder across consecutive route cycles is typical in a Selective Laser Melting (SLM) process since it is more sustainable and cost-effective. The theoretical part of the paper is oriented on the explanation of the SLM method principle, construction, and parameters of the device Renishaw AM250 used for manufacturing samples made of AlSi10Mg aluminium alloy. The experimental part focuses on evaluating powders that had been used in the process for a long time with periodic ‘rejuvenation’. The main aim will be to monitor whether the samples will be affected and if they achieved the required quality of mechanical properties and compare results with virgin powder and manufacturer sheets for virgin powders. The experimental part further describes the procedures and analysis of the microstructure of the samples. AlSi10Mg aluminium alloy was chosen because of an assumption that it will be sensitive to increased oxygen content. A strong affinity for oxygen uptake exists in AlSi10Mg. Therefore, preventing the contamination, careful handling is required.
Keywords: SLM, AlSi10Mg, powder, Additive manufacturing
Grants and funding:
This article was funded by the University of ®ilina project 313011ASY4 „Strategic implementation of additive technologies to strengthen the intervention capacities of emergencies caused by the COVID-19 pandemic“
Received: August 30, 2022; Revised: December 22, 2022; Accepted: January 13, 2023; Prepublished online: April 24, 2023; Published: May 3, 2023 Show citation
References
- SIMCHI, A. (2006). Direct laser sintering of metal powders: Mechanism, kinetics, and microstructural features. Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing, 428(1- 2): pp. 148-158.
Go to original source...
- DING, D, et.al. (2015). Wire-feed additive manufacturing of metal components: technologies, developments, and future interests. 2015. DOI 10.1007/s00170-015-7077-3.EIT Biomedical engineering. (2013). Aditívna výroba - Laserové sinterovanie kovov. Koąice: s.n., 2013
Go to original source...
- FATHOM. (2015). EOS // ALUMINIUM ALSI10MG. Studio Fathom. [Online] 2015. https://studiofa- thom.com/wp-.
- 3D Systems. (2018). LaserForm® AlSi10Mg (A). 3D Systems. [Online] 20. 3 2018. https://www.3dsy.
- 3DPRINTINGMEDIA.NETWORK. (2016). Sisma Unveils myrev100 SLA 3D Printer. 2016.
- KRI©TOFOVÁ, P., ROUDNICKÁ, M., KUBÁSEK, J., PALOU©EK, D., SUCHÝ, J., VOJTĚCH, D. (2019). Influence of Production Parameters on the Properties of 3D Printed Magnesium Alloy Mg-4Y- 3RE-Zr (WE43). In: Manufacturing Technology, Vol. 19, No. 4, pp. 613-118. ISSN 1213-2489
Go to original source...
- ROUDNICKA M., MISURAK M., VOJTECH, D. (2019). Differences in the Response of Additively Manufactured Titanium Alloy to Heat Treatment - Comparison between SLM and EBM[J]. Manufacturing Technology, 19(4):688-673.
Go to original source...
- OSAKADA K, SHIOMI M. (2006). Flexible manufacturing of metallic Products by selective laser melting of Powder[J]. International Journal of Machine Tools & Manufacture, 2006, 46 (11): pp.1188-1193.
Go to original source...
- KURIC, I. et al., "Approach to Automated Visual Inspection of Objects Based on Artificial Intelligence,"
- Appl. Sci., vol. 12, no. 2, 2022, doi: 10.3390/app12020864.
Go to original source...
- [10] Hunt, J.D., Lu, S.Z. Numerical modeling of cellular/dendritic array growth: spacing and structure predictions. Metall Mater Trans A 27, 611-623 (1996). https://doi.org/10.1007/BF02648950.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.