Manufacturing Technology 2023, 23(1):2-10 | DOI: 10.21062/mft.2023.011

Evaluation of Riveting Force Influence on the Quality of Riveted Joint of Aluminium Alloy EN AW - 6016

Josef Bradáč ORCID..., Jiří Sobotka ORCID...
Department of Mechanical and Electrical Engineering, SKODA AUTO Vysoká škola o.p.s. Na Karmeli 1457, 291 01 Mladá Boleslav. Czech Republic.

Joining technologies are very important aspects of production process in the automotive. Especially regarding the use of newly developed types of materials (e.g. ultra high-strength steels or aluminium alloys), in addition to welding technology, e.g. riveting or adhesive bonding technologies are used. Submitted article evaluates the effect of the riveting force on the final quality of riveted joint when joining aluminium alloy EN AW-6016 (thickness 2 mm). The actual evaluation of the riveted joint was carried out using a shear test, measuring the hardness HV01 and deformation analysis of specimen using non-contact optical scanning (ATOS III Triple Scan system).

Keywords: Riveting, Aluminium Alloy, Shear Test, Hardness, Digitalization

Received: August 22, 2022; Revised: December 5, 2022; Accepted: April 6, 2023; Prepublished online: April 24, 2023; Published: May 3, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Bradáč J, Sobotka J. Evaluation of Riveting Force Influence on the Quality of Riveted Joint of Aluminium Alloy EN AW - 6016. Manufacturing Technology. 2023;23(1):2-10. doi: 10.21062/mft.2023.011.
Download citation

References

  1. BRADÁČ, J., SOBOTKA, J. (2020). Technical and Economic Aspects of Using Magnesium Alloys for Production of Car Components. In: Proceedings of the 1st International Conference on Automotive Industry 2020, ŠKODA AUTO University, pp. 258 - 266, ISBN 978-80-7654-016-3
  2. GIULIANO, G., POLINI, W. (2021). Weight Reduction in an AA2017 Aluminum Alloy Part through the Gas Forming Process of a Blank with a Variable Thickness. In: Manufacturing Technology, Vol. 21, No. 2, pp. 192 - 198. ISSN 1213-2489 Go to original source...
  3. GODE, C. (2021). Influence of a low-temperature plastic-deformation process on the microstructure of an Al-Si-Mg aluminum alloy. In: Materiali in Tehnologije / Materials and Technology, Vol. 55, No. 2, pp. 283 - 291. ISSN 1580-2949 Go to original source...
  4. LAH, A. Š., et al. (2021). The Influence of chemical composition and heat treatment on the mechanical properties and workability of the aluminium alloy EN AW 5454. In: Materiali in Tehnologije / Materials and Technology, Vol. 55, No. 5, pp. 709 - 716. ISSN 1580-2949 Go to original source...
  5. WANG H., YANG, K., LIU, L. (2018). The analysis of welding and riveting hybrid bonding joint of alumi-num alloy and polyether-ether-ketone composites. In: Journal of Manufacturing Processes, Vol. 36, pp. 301 - 308. ISSN 1526-6125 Go to original source...
  6. KALINA, T., SEDLÁČEK, F. (2019). Design and Determination of Strength of Adhesive Bonded Joints. In: Manufacturing Technology, Vol. 19, No. 3, pp. 409 - 413. ISSN 1213-2489 Go to original source...
  7. AJABSHIR, S. Z., KAZEMINEZHAD, M., KOKABI, A.H. (2021). Manufacturing thinned friction-stir welded 1050 aluminum by post rolling: microstructure and mechanical properties. In: Materiali in Tehnologije / Materials and Technology, Vol. 55, No. 5, pp. 609 - 617. ISSN 1580-2949 Go to original source...
  8. PAN, B, et al. (2021). Corrosion behavior in aluminum/galvanized steel resistance spot welds and self-piercing riveting joints in salt spray environment. In: Journal of Manufacturing Processes, Vol. 70, pp. 608 - 620. ISSN 1526-6125 Go to original source...
  9. KASCAK, L., et al. (2020). Mechanical joining of aluminium alloy sheets. In: MM Science Journal, No. 5, pp. 4179-4182. ISSN 1805-0476 Go to original source...
  10. ZHANG, H. (2020). Influence of riveting sequence/direction on distortion of steel and aluminum sheets. In: Journal of Manufacturing Processes, Vol. 53, pp. 304 - 309. ISSN 1526-6125 Go to original source...
  11. BĚHAL, J., RŮŽEK, R. (2021). Effect of the rivet-hole tolerance on the stress-severity factor. In: Materiali in Tehnologije / Materials and Technology, Vol. 55, No. 2, pp. 237 - 242. ISSN 1580-2949 Go to original source...
  12. HUANG, Z. C., al. (2022). Physical property and failure mechanism of self-piercing riveting joints be-tween foam metal sandwich composite aluminum plate and aluminum alloy. In: Journal of Materials Research and Technology, Vol. 17, pp. 139 - 149. ISSN 2238-7854 Go to original source...
  13. MA, Y, et al. (2021). A Comparative Study of Friction Self-Piercing Riveting and Self-Piercing Riveting of Aluminum Alloy AA5182-O. In: Engineering, Vol. 7, pp. 1741 - 1750. ISSN 2095-8099 Go to original source...
  14. KARATHANASOPOULOS, N., PANDYA, K. S., MOHR, D. (2021). An experimental and numerical investigation of the role of rivet and die design on the self-piercing riveting joint characteristics of aluminum and steel sheets. In: Journal of Manufacturing Processes, Vol. 69, pp. 290 - 302. ISSN 1526-6125 Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.