Manufacturing Technology 2023, 23(2):143-152 | DOI: 10.21062/mft.2023.022

Investigation and Measurement of Nanomechanical Properties of the HSS Powder Metallurgy ASP2017 and ASP2055 Steels

Jana Escherová, Juraj Majerský ORCID..., Jozef Majerík ORCID..., Igor Barényi ORCID..., Henrieta Chochlíková
Faculty of Special Technology, A. Dubcek University of Trencin. Ku kyselke 469, 911 06 Trencin. Slovakia

The intention of the team of authors in the presented scientific article was experimental measurement with subsequent evaluation of nanomechanical properties of selected microstructural components of the investigated high-speed steels type ASP2017 and ASP2055 produced by powder metallurgy. The whole experiment was performed under laboratory conditions on an experimental apparatus called Hysitron TI 950 Triboindeneter. The used device is a part of the laboratory equipment of the Center for Diagnostics and Quality Testing of Materials. The proposed process of experimental research of the mentioned properties of PM steels was carried out precisely because of the relatively high require-ments for the use of this type of steel for the needs of special applications in the engineering industry. Therefore, the research of nanomechanical properties such as nanohardness H and the reduced and real Young's modulus Er and the Young's modulus of elasticity Es were therefore the subject of the authors' research. The authors proposed the use of a Berkovich geometry tip as a test or indentation body, respectively. In terms of the proposed structure of the article, the authors describe the current state of research from the assigned problem using database sources. The experimental part of their research already solves the obtained nanomechanical properties of individual components of the struc-ture of the tested PM steels, as well as the distribution of individual positions of indents. These were designed using so-called SPM scans (Scanning Probe Microscopy). Nanoindentation curves were generated from them using the Triboscan evaluation software. Based on the performed measurements and the Er obtained from them, and the Es was also calculated using mathematical relations. The authors graphically expressed the final values of nanomechanical quantities and described them in a discussion of the experiments.

Keywords: Quasistatic nanoindentation, Nanohardness, Reduced Young's modulus, Powder metallurgy steels, Berkovich indenter
Grants and funding:

This publication was created within the implementation of the project "Development and support of research - development activities of the Center for Quality Testing and Diagnostics of Materials in the field of specialization RIS3 SK", No. 313011W442, supported by the Operational Program Integrated Infrastructure and European Regional Development Fund

Received: December 27, 2021; Revised: March 28, 2023; Accepted: April 17, 2023; Prepublished online: April 25, 2023; Published: May 4, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Escherová J, Majerský J, Majerík J, Barényi I, Chochlíková H. Investigation and Measurement of Nanomechanical Properties of the HSS Powder Metallurgy ASP2017 and ASP2055 Steels. Manufacturing Technology. 2023;23(2):143-152. doi: 10.21062/mft.2023.022.
Download citation

References

  1. FISCHER - CRIPPS, A. C.: Nanoindentation Springer Science (3rd edition), New York, ISBN - 13: 9781461429609, 2013.
  2. 2 OLIVER, W., PHARR, G. M: An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments, Journal of Material Response, Vol. 7 (1992), Issue 6, p. 1564-1583. Go to original source...
  3. 3 FISCHER-CRIPPS, A. C.: Critical review of analysis and interpretation of nanoindentation test data, Surface and Coating Technology, Vol. 200 (2006), p. 4153-4165. Go to original source...
  4. 4 WANG, S., ZHAO, H.: Low temperature nanoindentation: development and applications, MDPI Micromachines, Vol. 11 (2020), 25 p. Go to original source...
  5. 5 NAIMI-JAMAL, M. R., KAUPP, G.: Quantitative evaluation of nanoindents: do we need more reliable mechanical parameters for the characterization of materials? International Journal of Materials Research, Vol. 96 (2005), Issue 11, p. 1226-1236. Go to original source...
  6. 6 NGUYEN, V. L., KIM, E. A., YUN, J., CHOE, J., YANG, D. Y., LEE, CH. W., YU, J., H.: Nano-mechanical behavior of H13 tool steel fabricated by selective laser melting method, Metallurgical and material transactions A: Physical metallurgy and material science Vol. 50 (2019), Issue 2, p. 523-528. Go to original source...
  7. 7 NGUYEN, V. L., KIM, E. A., LEE, S. R., YUN, J. C., CHOE, J. H., YANG, D. Y., LEE, H. S., LEE, C. W., YU, J., H.: Evaluation of strain rate sensitivy of selective laser melted H13 tool steel using nanoindentation tests, Metallurgical and material transactions A: Metals, Vol. 8 (2018), p. 589. Go to original source...
  8. 8 MARASHI, J., YUKUSHINA, E., XIROUCHAKIS, P., ZANTE, R., FOSTER, J.: An evaluation of H13 tool steel deformation in hot forging conditions, Journal of Material Processing Technology, Vol. 246 (2017), p. 276-284. Go to original source...
  9. 9 LUONG NGUYEN, V., KIM, E., YUN, J., et al.: Evaluation of strain-rate sensitivity of selective laser melted H13 tool steel using nanoindentation tests, Metals MDPI, Vol. 8 (2018), p. 589-599. Go to original source...
  10. 10 YASAVOL, N., JAFARI, H.: Microstructure, mechanical and corrosion properties of friction stir-processed AISI D2 tool steel, Journal of Materials Engineering and Performance, Vol. 24 (2015), Issue 5, p. 2151-2157. Go to original source...
  11. 11 NURBANASARI, M., TSAKIROPOULOS, P., PALMIERE, E. J.: On the solidification of H23 tool steel, Trans Indian Inst Met, Vol. 67 (2014), Issue 6, p. 935-944. Go to original source...
  12. 12 BOUMAALI, B., NAIT ABDELLAH, Z., KEDDAM, M.: Characterization of bilayer (FeB/Fe2B) in AISI H13 work tool steel Koroze a ochrana materiálu, Vol. 65 (2021), Issue 2, p. 40-48. Go to original source...
  13. 13 MAJERÍK, J., BARÉNYI, I., SEDLÁK, J., KUSENDA, R., ECKERT, M.: Microstructural analysis of examined 33NiCrMoV15 steel and investigation of its nanomechanical properties after machining, Manufacturing Technology, Vol. 20 (2020), p. 72-77. Go to original source...
  14. 14 GROEB, M., FRITZ, M.: Process analysis on milled optical surfaces in hardened stainless steel, Journal of Manufacturing and Materials Processing, Vol. 67 (2019), Issue 3, 12 p. Go to original source...
  15. 15 NAGASHIMA, N., HAYKAWA, M., KIMURA, M.: Characterization of mechanical properties for ferritic heat-resisting steels (12Cr-2W) with different creep-fatigue properties by nanoindentation, Materials Transactions, Vol. 60 (2019), Issue 4, p. 495-502. Go to original source...
  16. 16 SU, J., TIAN, L., HU, R., LIU, H., FENG, T., WANG, J.: Effect of sputtering current on the comprehensive properties of (Ti, Al)N coating and high-speed steel substrate, Journal of Materials Engineering and Performance, Vol. 27 (2018), Issue 5, p. 2381-2387. Go to original source...
  17. 17 YAMAMOTO, M., TANAKA, M., FURUKIMI, O.: Hardness-deformation energy relationship in metals and alloys: a comparative evaluation based on nanoindentation testing and thermodynamic consideration, MDPI Materials, Vol. 14 (2021), 11 p. Go to original source...
  18. 18 LIU, Z., ZHANG, J., HE, B., ZOU, Y.: High speed nanoindentation mapping of a near-alpha titanium alloy made by additive manufacturing, Journal of Materials Research, Vol. 36 (2021), Issue 11, 12 p. Go to original source...
  19. 19 ZHU, Z., HUANG, H., LIU, J., YE, L., ZHU, Z.: Nanoindentation study on the creep characteristics and hardness of ion-irradiated alloys, MDPI Materials, Vol. 13 (2020), 12 p. Go to original source...
  20. 20 PÖHL, F., HARDES, C., SCHOLZ, F., FRENZEL, J.: Orientation dependent deformation behaviour of 316L steel manufactured by laser metal deposition and casting under local scratch and indentation load, MDPI Materials, Vol. 13 (2020), 19 p. Go to original source...
  21. 21 KLUČIAR, P., BARÉNYI, I., MAJERÍK, J.: Nanoindentation analysis of Inconel 625 alloy weld overlay on 16Mo3 steel, Manufacturing Technology, Vol. 22 (2022), Issue 1, p. 26-33. Go to original source...
  22. 22 BASAVARAJAPPA P. N., HEGDE, M. M. R., RAJENDRACHARI, S., SURENDRANATHAN, A. O.: Invsetigation of structural and mechanical properities of nanostructured TiMgSr alloy for biomedical applications, Biointerface Research in Applied Chemistry, Vol. 13 (2022), Issue 2, 12 p. Go to original source...
  23. 23 MENCIN, P., TYNE, C. J. V., LEVY, B. S.: A method for measuring the hardness of the surface layer on hot forging dies using a nanoindenter, Journal of Material Engineering Performance, Vol. 18 (2009), p. 1067-1072. Go to original source...
  24. 24 HAMID, A.: Deposition, microstructure and nanoindentation of multilayer Zr nitride and carbonitride nanostructured coat-ings, Scientific reports, Vol. 12 (2022), 16 p. Go to original source...
  25. 25 SVOBODOVÁ, J., LYSOŇKOVÁ, I., KREJČÍ, M.: Microhardness and nanohardness measurement of composite coat-ings applied to aluminium substrate, Manufacturing Technology, Vol. 19 (2019), Issue 4, p. 700-705. Go to original source...
  26. 26 GONZÁLES-HERNÁNDEZ, A., FLORES, M., MORALES, A. B., CAICEDO, J. C., DE SÁNCHEZ, N. A., BARRAGÁN RAMÍREZ, R..: Optical and tribomechanical characterization in metal-ceramic multilayer coatings, Revista Mexicana de Física, Vol. 66 (2020) Issue 4, p. 496-503. Go to original source...
  27. 27 PAUL, V., WAKEDA, M., AMEYAMA, K., OTA-KAWABATA, M., OHMURA, T.: Local deformation behaviour of the copper harmonic structure near grain boundaries investigated through nanoindentation, MDPI Materials, Vol. 14 (2021), 12 p. Go to original source...
  28. 28 OHMURA, T., WAKEDA, M..: Pop-in phenomenon as a fundamental plasticity probed by nanoindentation technique, MDPI Materials, Vol. 14 (2021), 30 p. Go to original source...
  29. 29 XIANG, S., YANG, X., LIANG, Y., WANG, L.: Texture evolution and nanohardness in Cu-Nb composite wires, MDPI Materials, Vol. 14 (2021), 12 p. Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.