Manufacturing Technology 2023, 23(3):290-297 | DOI: 10.21062/mft.2023.034
A Design of Experiment Analysis Approach to Improve Part Quality in 3D Printing
- Department of Mechanical Techniques, Al-Nasiriya Technical Institute, Southern Technical University, Thi-Qar, Al-Nasiriya 64001, Iraq
Fused Deposition Modeling (FDM) is one of the widely used technologies of additive manufacturing. The concern over the surface quality and dimensional accuracy is getting increased among the research community. The design of the experimental methodology is based on the analysis of variance (ANOVA) of fractional factorial design. This analysis was used to study the effect of layer thickness, extrusion temperature, speed of deposition, and fill density on dimensional accuracy and surface roughness of the model developed by FDM. Polylactic Acid (PLA) material has been selected in this work as it is inexpensive, easy to print, and biodegradable. The results showed that layer thickness is an effective factor in determining surface roughness. Fill density (X and Z dimensions), layer thickness (Y dimension), and speed of deposition (Z dimension) are significant factors for dimensional accuracy. Regarding surface roughness, curvature was found to be significant; however, the minimum optimization point was not reached. Thus, more experiments are required to be carried out to get the minimum point. For dimensional accuracy optimization, the dimensions along X, Y, and Z were realized to be more accurate at lower levels of every factor except for fill density (D), which was optimized
Keywords: Fused Deposition Modeling, Polylactic Acid, Design Expert Software, Dimensional Accuracy, Surface Roughness
Received: October 5, 2022; Revised: April 27, 2023; Accepted: May 4, 2023; Prepublished online: May 4, 2023; Published: July 5, 2023 Show citation
References
- KRAUSE, F. L., CIESLA, M., STIEL, C., & ULBRICH, A. (1997). Enhanced rapid prototyping for faster product development processes. In: CIRP Annals, Vol. 46, No.1, pp. 93-96. ISSN:0007-8506
Go to original source...
- POUR, M. A., ZANARDINI, M., BACCHETTI, A., & ZANONI, S. (2016). Additive manufacturing impacts on productions and logistics systems. In: IFAC-PapersOnLine, Vol.49, No.12, pp. ISSN: 2405-8963
Go to original source...
- GUO, N., & LEU, M. C. (2013). Additive manufacturing: technology, applications and research needs. In: Frontiers of Mechanical Engineering, Vol. 8, No.3, pp. 215-243. ISSN:2095-0233
Go to original source...
- MELLOR, S., HAO, L., & ZHANG, D. (2014). Additive manufacturing: A framework for implementation. In: International journal of production economics, Vol. 149, pp. 194-201. ISSN 0925-5273
Go to original source...
- ISMAIL, K. I., YAP, T. C., & AHED, R. (2022). 3D-Printed Fiber-Reinforced Polymer Composites by Fused Deposition Modelling (FDM): Fiber Length and Fiber Implementation Techniques. In: Polymers, Vol. 14, No.21, pp. 4659. ISSN:2073-4360
Go to original source...
- MUELLER, B. (2012). Additive manufacturing technologies-Rapid prototyping to direct digital manufacturing. In: Assembly Automation, Vol. 32, No.2. ISSN: 0144-5154
Go to original source...
- BEMARD, A., & FISCHER, A. (2002), New trends in rapid product development, In: CIRP Annals, Vol.51, No.2, pp. 635-652. ISSN:0007-8506
Go to original source...
- KRUTH, J. P., LEU, M. C., & NAKAGAWA, T. (1998). Progress in additive manufacturing and rapid prototyping, In: CIRP Annals, Vol.47, No.2, PP. 525-540. ISSN:0007-8506
Go to original source...
- WIEDEMANN, B., & JANTZEN, H. A. (1999). Strategies and applications for rapid product and process development in Daimler-Benz AG, In: Computers in Industry, Vol.39, No.1, PP. 11-25. ISSN:0166-3615
Go to original source...
- M.H. TOO, K.F. LEONG, C.K. CHUA, Z.H. DU, S.F. YANG, C.M. CHEAH and S.L. HO. (2002). Investigation of 3D Non Random Porous Structures by Fused Deposition Modeling. In: The International Journal of Advance Manufacturing Technology, Vol. 19, pp. 217-223. ISSN:0268-3768
Go to original source...
- CHEAH, C. M., CHUA, C. K., LEE, C. W., FENG, C., & TOTONG, K. (2005). Rapid prototyping and tooling techniques: a review of applications for rapid investment casting. In: The International Journal of Advanced Manufacturing Technology, Vol.25, No.3-4, PP. 308-320. ISSN:0268-3768
Go to original source...
- KIM, G. D., & OH, Y. T. (2008). A benchmark study on rapid prototyping processes and machines: quantitative comparisons of mechanical properties, accuracy, roughness, speed, and material cost, In: Proceedings of the Institution of Mechanical Engineers. Part B: Journal of Engineering Manufacture, Vol. 222, No.2, pp. 201-215. ISSN:0954-4054
Go to original source...
- IPPOLITO, R., IULIANO, L., & GATTO, A. (1995). Benchmarking of rapid prototyping techniques in terms of dimensional accuracy and surface finish. In: CIRP annals, Vol. 44, No.1, pp. 157-160. ISSN:0007-8506
Go to original source...
- L. Hamouti, O. El Farissi, O. Outemsaa, M. Modar. (2022). Artificial Model For Prediction Of Flexural Strength Of A Pla Prototype Printed. In: International Journal on Technical and Physical Problems of Engineering (IJTPE), Vol. 14, No.4, pp. 357 - 362. ISSN:2077-3528
- Sedlák, J., Joska, Z., Hrbáčková, L., Juřičková, E., Hrušecká, D., & Horák, O. (2022). Determination of mechanical properties of plastic components made by 3D printing. In: Manufacturing Technology. Vol. 22, No. 6, pp. 733-746. ISSN 1213-2489
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.