Manufacturing Technology 2023, 23(3):348-353 | DOI: 10.21062/mft.2023.043

Application of the Method of Planned Experiment for the Evaluation of the Surface Roughness Parameter Ra

Ľudmila Timárová ORCID..., Alena Breznická ORCID..., Beáta Kopiláková ORCID...
Faculty of Special Technology, Alexander Dubček University of Trenčín. Ku kyselke 469, 911 06 Trenčín. Slovak Republic

The basic process of acquiring new knowledge is trial/experiment. We can define an experiment as a certain process that we prepare, organize and plan in order to know the object under investigation. Each experiment requires a multifaceted activity associated with professional knowledge, preparation of material security, espe-cially security with measuring devices and measurement methods for determining the correct (objective) measured values. Planning experiments and analyzing the obtained results are important stages in revealing the nature and course of the technological process. With the planned experiment, we try to create such con-ditions that the range of experiments is as small as possible, but the volume and form of information are of the highest quality. The article presents the method of the planned experiment and its use in industrial prac-tice. The mentioned methodology of the planned experiment is applied to the calculation of the mean arith-metic value of the surface roughness Ra depending on the cutting parameters. The advantage of this method is that it increases the accuracy of the obtained results, but mainly reduces the number of performed at-tempts.

Keywords: Planned Experiment, Cutting Parameters, Surface Roughness

Received: February 17, 2023; Revised: June 7, 2023; Accepted: June 16, 2023; Prepublished online: June 16, 2023; Published: July 5, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Timárová Ľ, Breznická A, Kopiláková B. Application of the Method of Planned Experiment for the Evaluation of the Surface Roughness Parameter Ra. Manufacturing Technology. 2023;23(3):348-353. doi: 10.21062/mft.2023.043.
Download citation

References

  1. JAKUBA, M., NOVOTNÝ, R. (2003). Aplikace plánovaného experimentu v optimalizaci hodnot znaků jakosti dos-ahovaných technologickým procesem. In. Technické aspekty zabezpečovaní jakosti, VUT, Brno. ISBN 80-214-2291-2.
  2. KADOMSKAJA, K. P. (2002). Methods for processing experimental results and designing an experiment. [In Russian] Novosibirsk, 72 p. NSTU publishing house.
  3. ZAHRADNICEK, R., PROKES, T., BENES, L. (2017). The Graphene Oxide Spincoating Optimalization by Planned Experiment. In: Manufacturing Technology 2017, Vol.17, No. 4, pp. 635-639. Go to original source...
  4. CIERNA, H., TAVODOVA, M. (2013). Using the design of experiment method to evaluate quality of cuts after cutting aluminum alloy by AWJ. In: Manufacturing Technology, Vol. 13, No. 3, pp. 303-307. Go to original source...
  5. HRICOVA, J., NAPRSTKOVA, N. (2015). Surface Roughness Optimization in Milling Aluminium Alloy by Using the Taguchi's Design of Experiment. In: Manufacturing Technology, Vol. 15, No. 4, pp. 541-546. Go to original source...
  6. GERLICI, J., GORBUNOV, M., KRAVCHENKO, K., LACK, T. (2020). Planning of a numerical experiment in order to determine the effect of operating factors on the traction-adhesion properties of locomotives. In: Manufacturing Technology 2020, Vol. 20, No. 6, pp.728-732. Go to original source...
  7. KUNDRÁK, J., FELHŐ, C., NAGY, A. (2022). Analysis and Prediction of Roughness of Face Milled Surfaces using CAD Model. In: Manufacturing Technology 2022, Vol. 22, No. 5, pp. 558-572. Go to original source...
  8. HRONEK, O., ZETEK, M., BAKSA, T., ADÁMEK, P. (2018). Surface Quality Analysis of Cutting Toll Mi-crogeometry to Achieve Higher Durability. In. Manufacturing Technology (2018), Vol. 18, No. 1, pp. 39-46 Go to original source...
  9. MAJERÍK, J., DUBOVSKÁ, R., BAŠKA, I., JAMBOR, J. (2018). Experimental Investigation and Measurement of Surface Roughness and Cutting Forces while Turning AlCu3MgMnPb Aluminium Alloy. In Manufacturing Technology (2018). Vol. 18, No. 1, pp. 66-71. Go to original source...
  10. MÁDL, J., HOLEŠOVSKÝ, F. (2008). Integrita obrobených povrchů z hlediska funkčních vlastností, UJEP, Ústi nad Labem ISBN 978-80-7414-095-2.
  11. FARSKÝ, J., ZETEK, M., BAKŠA, T., KUBÁTOVÁ, D., YUAN, H. (2020). Effect of the cutting conditions on surface roughness during 5-axis grinding of Maraging steel MS1. In Manufacturing Technology (2020). Vol. 20, No. 4, pp. 423-428. Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.