Manufacturing Technology 2023, 23(4):545-550 | DOI: 10.21062/mft.2023.063
Effect of Milling Parameters on the Surface Roughness of SiCp/Al Materials
- 1 Aviation Equipment Manufacturing Industry College, Chengdu Aeronautic Polytechnic, Chengdu, 610100, China
- 2 Xiamen Golden Egret Special Alloy Co. Ltd, Xiamen, 361006, China
The presence of reinforcing particles SiCp seriously affects the cutting surface quality of SiCp/Al materials.In this study, different machining parameters were tested to obtain good surface quality, and the surface quality of SiCp/Al alloy material under different milling parameters was studied by using the surface profilometer and scanning electron microscope to explore the effect of cutting pa-rameters on surface quality. The results showed that the Surface roughness value increased with the increase of feed rate and milling speed, and milling speed was the dominant factor in the microstruc-ture evolution of the machined surface. In addition, an exponential model related to feed rate and milling speed was constructed.
Keywords: SiCp/Al, Cutting Parameters, Surface Roughness, Parameter Optimization
Grants and funding:
This research was financially supported by the Chengdu Aeronautic Polytechnic Natural Science Project, Grant Number ZZX0623070(Modeling of Relationship between Cutting Parameters and Surface Quality of SiCp/Al Composites)
Received: May 20, 2023; Revised: August 2, 2023; Accepted: August 16, 2023; Prepublished online: August 16, 2023; Published: September 5, 2023 Show citation
References
- LIU C, GAO L, JIANG X.G, et al.(2020).Analytical modelling of subsurface damage depth in machining of SiCp/Al Composites.In: International Journal of Mechanical Sciences. Vol.185, No.1,pp.105874,ISSN 0020-7403
Go to original source...
- J Q LIN, C WANG, M M LU, et al.(2022). Modelling and investigation of cutting force for SiCp/Al compo-sites during ultrasonic vibration-assisted turning. In: Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Vol.236, No.3, pp. 1013-1022, ISSN 0954-4089
Go to original source...
- ZHOU J K, LU M M, LIN J Q, et al.(2022) Investigation and simulation based on mesoscopic model of SiCp/Al composites during precision machining: deformation mechanism and surface quality. In: The International Journal of Advanced Manufacturing Technology, Vol 119, No.3, pp.2173-2186, ISSN 0268-3768
Go to original source...
- WANG Y F, LIAO W H, YANG K, et al.(2019) Simulation and experimental investigation on the cutting mechanism and surface generation in machining SiCp/Al MMCs.In: International Journal of Advanced Manufacturing Technology, Vol.100, No.5.pp.1393-1404, ISSN 0268-3768
Go to original source...
- DUAN CH Z, SUN W, ZHAN FENG, et al.(2018) Defects formation mechanism and evaluation of surface roughness in machining Al/SiCp composites. In: Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol.12, No.1, pp.17-30, ISSN 1881-3054
Go to original source...
- KUNDRÁK, J., FELHŐ, C., & NAGY, A. (2022). Analysis and Prediction of Roughness of Face Milled Surfaces using CAD Model. In: Manufacturing Technology, Vol. 22, No. 5, pp.558-572.ISSN 1213-2489
Go to original source...
- HUANG S T, GUO L, YANG H C, SU Y, XU LF.(2019) Study on characteristics in high-speed milling SiCp/Al composites with small particles and high volume fraction by adopting PCD cutters with different grain sizes. In: International Journal of Advanced Manufacturing Technology, Vol.102, No.9, pp.3563-3571, ISSN 0268-3768
Go to original source...
- ZHAO, C., MA, C., MA, Z., YANG, J., & LI, M. (2022). Analysis of the Effect of Preset Surface Texture on Hard State Cutting. In: Manufacturing Technology, Vol.22, No.3, pp.384-394.ISSN 1213-2489
Go to original source...
- DENG, B., ZHOU, L., PENG, F., YAN, R., YANG, M., AND LIU, M. (2018). Analytical Model of Cutting Force in Micromilling of Particle-Reinforced Metal Matrix Composites Considering Interface Failure. In: The Journal of Manufacturing Science and Engineering,Vol.140, No.8,pp.081009,ISSN 1528-8935
Go to original source...
- NARDIN, M., & SCHULTZ, J.(1996) Relationship between Work of Adhesion and Equilibrium Interatomic Distance at the Interface. In:Langmuir, Vol.12, No.17,pp.4238-4242, ISSN 4238-4242
Go to original source...
- KUNDRÁK, J., SZTANKOVICS, I., & MOLNÁR, V. (2021). Accuracy and topography analysis of hard machined surfaces. In: Manufacturing Technology, Vol.21, No.4, pp.512-519.ISSN 1213-2489
Go to original source...
- MAJERÍK, J., et al.(2023). Surface Roughness, Topography, Accuracy, Chip Formation Analysis & Investigation of M390 and M398 Steels after Hard Machining. In: Manufacturing Technology, Vol.23, No.1, pp.60-72.ISSN 1213-2489
Go to original source...
- TIMÁROVÁ, Ľ., BREZNICKÁ, A., & KOPILÁKOVÁ, B.(2023). Application of the Method of Planned Experiment for the Evaluation of the Surface Roughness Parameter Ra. In: Manufacturing Technology, Vol.23, No.3, pp.348-353, ISSN 1213-2489
Go to original source...
- TOMADI SH, GHANI JA, HARON CHC, AYU HM, DAUD R.(2017)Effect of Cutting Parameters on Surface Roughness in End Milling of AlSi/AlN Metal Matrix Composite. In: Procedia Engineering.Vol.184, pp.58-69.ISSN 1877-7058
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.