Manufacturing Technology 2023, 23(5):589-596 | DOI: 10.21062/mft.2023.068
The Influence of Accelerated Electron Irradiation on the Change of Tribological Behavior of Polymeric Materials PET, PTFE & PE2000C
- Faculty of Special Technology, Alexander Dubcek University of Trenčín, Ku Kyselke 469, 911 06 Trenčín, Slovakia
The presented work deals with the study of the effect of increasing the doses of irradiation by accel-erated electrons on the sliding properties of polymer materials. Due to the influence of radiation, sur-face roughness changes occur on the surface of the experimental materials, which lead to changes in the properties of the coefficient of friction on the selected polymer materials. Three types of polymer materials PET, PTFE and PE2000C were used for the experimental research, which, due to their properties, are used for different types of sliding products. A steel ball of G40 material was used as a pressure material, which moved along a linear path on which the load was increased from 10 N to 100 N. Electron beam accelerators with the conversion of electrons to X-rays combine the advantages of a high ability to penetrate gamma photons sources and high performance of electron beam devices. The application possibilities of the device are wide due to the dual mode of operation (electron beam or X-ray beam) and a wide range of applicable doses and also dose rates.
Keywords: Coefficient of friction, Polymers, Materials, Linear electron accelerator, Roughness
Grants and funding:
This work was supported by the Research Agency of the Ministry of Education, Science, Research and Sport of the Slovak Republic under the contract (ITMS2014+) no. 313011W442-CEDITEK II
Received: April 18, 2023; Revised: July 11, 2023; Accepted: September 1, 2023; Prepublished online: September 15, 2023; Published: December 6, 2023 Show citation
ACS | AIP | APA | ASA | Harvard | Chicago | IEEE | ISO690 | MLA | NLM | Turabian | Vancouver |
References
- WYPYCH, G. (2022). Handbook of polymers. 3rd edition. Elsevier. ISBN 978-1-927885-96-3.
Go to original source...
- STUDENY, Z., KRBATA, M., DOBROCKY, D., ECKERT, M., CIGER, R., KOHUTIAR, M., MIKUS, P. (2022). Analysis of Tribological Properties of Powdered Tool Steels M390 and M398 in Con-tact with Al2O3. In: Materials, Vol. 15, 7562.
Go to original source...
- KRBAŤA, M., MAJERÍK, J., BARÉNYI, I., MIKUŠOVÁ, I. & KUSMIČ, D. (2019). Mechanical and Tribological Features of the 90MnCrV8 Steel after Plasma Nitriding. In: Manufacturing Technology, Vol. 19, pp. 238-242.
Go to original source...
- KRBATA, M., ECKERT, M., MAJERIK, J., BARENYI, I. (2020). Wear Behaviour of High Strength Tool Steel 90MnCrV8 in Contact with Si3N4. In: Metals, Vol. 10, 756.
Go to original source...
- KRBATA, M., ECKERT, M., BARTOSOVA, L., BARENYI, I., MAJERIK, J., MIKUŠ, P., RENDKOVA, P. (2020). Dry Sliding Friction of Tool Steels and Their Comparison of Wear in Contact with ZrO2 and X46Cr13. In: Materials, Vol. 13, 2359.
Go to original source...
- ASHFAQ, A., CLOCHARD, M. C., COQUERET, X., DISPENZA, C., DRISCOLL, M. S., ULAŃSKI, P., AL-SHEIKHLY, M. (2020). Polymerization reactions and modifications of polymers by ionizing radiation. In: Polymers, Vol. 12, No. 12, 2877.
Go to original source...
- JANÍK, R., KOHUTIAR, M., PAJTÁŠOVÁ, M., ONDRUŠOVÁ, D., SKALKOVÁ, P., ECKERT, M. (2022). Application of diffuse coplanar surface barrier plasma discharge to polymeric materials. In: Materi-alwissenschaft und Werkstofftechnik, Vol. 53, No. 4, pp. 494-502.
Go to original source...
- JANÍK, R., KOHUTIAR, M., DUBEC, A., ECKERT, M., MORICOVÁ, K., PAJTÁŠOVÁ, M., KRBATA, M. (2022). DMA Analysis of Plasma Modified PVC Films and the Nature of Initiated Surface Changes. In: Materials, Vol. 15, No. 13, 4658.
Go to original source...
- JANÍK, R., KOHUTIAR, M., PAJTÁŠOVÁ, M., DUBEC, A., PAGÁČOVÁ, J., & ŠULCOVÁ, J. (2020). The impact of DCSBD plasma discharge on polypropylene. In: IOP Conference Series: Materials Science and Engineering, Vol. 776, No. 1, 012090.
Go to original source...
- BARYLSKI, A., SWINAREW, A. S., ANIOŁEK, K., KAPTACZ, S., GABOR, J., STANULA, A., KNECHTLE, B. (2020). Tribological and mechanical behavior of graphite composites of polytetrafluoro-ethylene (PTFE) irradiated by the electron beam. In: Polymers, Vol. 12, No. 8, 1676.
Go to original source...
- ASANO, T., MINA, M. F., NISHIDA, A., YOSHIDA, S., & FUJIWARA, Y. (2001). Crystallization of a low molecular weight polyethylene and paraffins under a temperature gradient. In: Journal of Macromolecular Science, Part B, Vol. 40, No. 3-4, pp. 355-367.
Go to original source...
- ŠAGÁTOVÁ, A., FÜLÖP, M., PAVLOVIČ, M., SEDLAČKOVÁ, K., & NEČAS, V. (2020). Electron-beam accelerator with conversion to X-rays: optimal radiation type according to application. In: Radiation Physics and Chemistry, Vol. 172, 108789.
Go to original source...
- CLELAND, M. R., GREGOIRE, O., STICHELBAUT, F., GOMOLA, I., GALLOWAY, R. A., & SCHLECHT, J. (2005). Energy determination in industrial X-ray processing facilities. In: Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms, Vol. 241, No. 1-4, pp. 850-853.
Go to original source...
- DARÁŽOVÁ, Ľ., ŠAGÁTOVÁ, A., NEČAS, V., FÜLÖP, M., & HAN, B. (2016). Radiation degradation of pcbs in sediments: comparison of two methods. In: Acta Polytechnica CTU Proceedings, Vol. 4, pp. 19-21.
Go to original source...
- HUBER, H., & SCHNABEL, T. (2015). Electron beam irradiation of wood: an experimental parameter study. In: Forest Products Journal, Vol. 65, No. 3-4, S2-S2.
- ALLIANCE, G. I. P., INTERNATIONAL IRRADIATION ASSOCIATION. (2020). A Comparison of Gamma, E-beam, X-ray and Ethylene Oxide Technologies for the Industrial Sterilization of Medical Devices and Healthcare Products.
- DOBROCKY, D., POKORNY, Z., VITEK, R., PROCHAZKA, J., STUDENY, Z., JOSKA, Z., SEDLAK, J., SLANY, M., KOLOMY, S. (2022). Possibilities of Using the Duplex System Plasma Nitriding + CrN Coating for Special Components. In: Coatings, Vol. 12, 1953.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.