Manufacturing Technology 2023, 23(5):670-675 | DOI: 10.21062/mft.2023.070

Analysis of the Coating Delamination after Laser Beam Cutting

Anna Mičietová ORCID...1, Miroslav Neslušan ORCID...1, Zuzana Florková ORCID...2, Mária Čilliková ORCID...1
1 Faculty of Mechanical Engineering, University of Žilina, Univerzitná 1, 01026 Žilina. Slovakia
2 Research Centre, University of Žilina, Univerzitná 1, 01026 Žilina. Slovakia

This paper analyses surface after laser beam machining with respect of surface height irregularities, residual stress state as well as microstructure on the low alloyed steel S 235. Surface after laser beam machining is investigated due to its specific nature resulting into coating delamination. This coating delamination can be found especially in the regions in which component shape or/and curvature of the profile is altered. Especially the components corners suffer from the delamination due to exten-sive surface heating and presence of brittle oxides layer. The thickness of this oxides layer is hetero-geneous with respect of the component thickness as well as the component geometry. It was found the oxides layer is the thermally initiated process since in these regions the underlying matrix also exhibits the higher thickness of the heat affected zone and higher degree of the hardening expressed in term of HV0.1. Furthermore, also the compressive residual stresses exhibit higher amplitudes in the region remarkably affected by the thermal cycle.

Keywords: Laser beam machining, Oxidation, Delamination, Surface hardening
Grants and funding:

This publication was realized with support of the KEGA project 010ŽU-4/2021 and VEGA project 1/0052/22

Received: June 5, 2023; Revised: July 6, 2023; Accepted: September 1, 2023; Prepublished online: September 15, 2023; Published: December 6, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Mičietová A, Neslušan M, Florková Z, Čilliková M. Analysis of the Coating Delamination after Laser Beam Cutting. Manufacturing Technology. 2023;23(5):670-675. doi: 10.21062/mft.2023.070.
Download citation

References

  1. YANG, G., XIE, Y., ZHAO, S., REN, Y., WANG, CH. (2022). Methods and Mechanism of Powder Mixing for Selective Laser Melting. In: Manufacturing Technology, Vol. 22, No. 1, pp. 102-110. Czech Republic. ISSN: 1213-2489. Go to original source...
  2. PRAVEENKUMAR, K., SWAROOP, S., MANIVASAGAM, G. (2023). Effect of multiple laser shock peening without coating on residual stress distribution and high temperature dry sliding wear behaviour of Ti-6Al-4 V alloy. In: Optics & Laser Technology, Vol. 164, 109398. Germany. ISSN: 1879-2545. Go to original source...
  3. PROCHAZKA, J., VILIS, J., DOBROCKY, D., SPERKA, P. (2022). Modification of Diffusion Layers by Laser Shock Peening. In: Manufacturing Technology, Vol. 22, No. 6, pp. 724-732. Czech Republic. ISSN: 1213-2489. Go to original source...
  4. HRADIL, D., NOVÝ, Z., HODEK, J., KOUKOLÍKOVÁ, M., SZYSZKO, A. (2023). Effect of Laser Traverse Speed during Laser Hardening on Hardness Distribution and Microstructure of Hot Work Tool Steel H11. In: Manufacturing Technology, Vol. 23, No. 2, pp. 153-160. Czech Republic. ISSN: 1213-2489. Go to original source...
  5. YADAV, R., GOYAL, D.K., KANT, R. (2022). Multi-scan laser bending of duplex stainless steel under different cooling conditions. In: CIRP Journal of Manufacturing Science and Technology, Vol. 39, pp. 345-358. Switzerland. ISSN: 1755-5817. Go to original source...
  6. MIČIETOVÁ, A., ČILLIKOVÁ, M., NESLUŠAN, M. (2013). Influence of surface geometry and structure after non-conventional methods of parting on the following milling operations. In: Manufacturing Technology, Vol. 13, No. 1, pp. 199-204. Czech Republic. ISSN: 1213-2489. Go to original source...
  7. LI, W., RONG, Y., HUANG, Y., CHEN, L., YANG, Z., ZHANG, G. (2023). Effect of thermal damage on dynamic and static mechanical properties of CFRP short pulse laser hole cutting. In: Engineering Fracture Mechanics, Vol. 286, 109306. Netherlands. ISSN: 0013-7944. Go to original source...
  8. SLAMLOOEI, M., ZANON, G., VALLI, A., BISON, P., BURSI, O.S. (2022). Investigation of thermal behaviur of structural steel S235N under laser cutting process: Experimental, analytical, and numerical studies. In: Engineering Structures, Vol. 269, 114754. United Kingdom. ISSN: 0141-0296. Go to original source...
  9. KHDAIR, I.A., MELAIBARI, A.A., (2023). Experimental evaluation of cut quality and temperature field in fiber laser cutting of AZ31B magnesium alloy using response surface methodology. In: Optical Fiber Technology, Vol. 77, 103290. Italy. ISSN: 1068-5200. Go to original source...
  10. HUANG, S., FU, Z., LIU, CH., WANG, CH. (2023). Interactional relations between ablation and heat affected zone (HAZ) in laser cutting of glass fiber reinforced polymer (GFRP) composite by fiber laser. In: Optics & Laser Technolgy, Vol. 158, part A, 108796. Germany. ISSN: 1879-545. Go to original source...
  11. VAJDOVÁ, A., MIČIETOVÁ, A., ČILLIKOVÁ, M., NESLUŠAN, M. (2015). Barkhausen noise emission of surfaces after laser beam machining. In: Manufacturing Technology, Vol. 15, No. 3, pp. 462-468. Czech Republic. ISSN: 1213-2489. Go to original source...
  12. MIČIETOVÁ, A., ČILLIKOVÁ, M., ČEP, R., NESLUŠAN, M., GANEV, N. (2023). Study of Residual Stresses and Austenite Gradients in the Surface after Hard Turning as a Function of Flank Wear and Cutting Speed. In: Materials, Vol. 16, 1709. Switzerland. ISSN: 1996-1944. Go to original source...
  13. WANG, J.Y., LIU, C.R. (1999). The effect of tool flank wear on the heat transfer, thermal damage and cutting mechanics in finishing hard turning. In: CIRP Annals, Vol. 48, pp. 53-58. USA. ISSN: 1726-0604. Go to original source...
  14. NADOLNY, K., ROMANOWSKI, M., SUTOWSKI, P. (2023). Assessing the technological quality of abrasive water jet and laser cutting processes by geometrical errors and a multiplicative indicator. In: Measurement, Vol. 217, 113060. United Kingdom. ISSN: 0263-2241. Go to original source...
  15. NESLUŠAN, M., BAHLEDA, F., MINÁRIK, P., ZGÚTOVÁ, K., JAMBOR, M. (2019). Non-destructive monitoring of corrosion extent in steel rope wires via Barkhausen noise emission. In: Journal of Magnetism and Magnetic Materials, Vol. 484, pp. 179-187. The Netherlands. ISSN: 0304-8853. Go to original source...
  16. PASTOREK, F., DECKÝ, M., NESLUŠAN, M., PITOŇÁK, M. (2022). Usage of Barkhausen Noise for Assessment of Corrosion Damage on Different Low Alloyed Steels. In: Applied Sciences, Vol. 11, 10646. Switzerland. ISSN: 2076-3417. Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.