Manufacturing Technology 2023, 23(5):597-603 | DOI: 10.21062/mft.2023.072

Design of an Injection Mould Utilizing Experimental Measurements and Reverse Engineering

Vladimír Bechný ORCID..., Miroslav Matuš ORCID..., Richard Joch ORCID..., Mário Drbúl ORCID..., Jozef Holubják ORCID..., Andrej Czán ORCID..., Michal Šajgalík ORCID..., Jaromír Markovič ORCID...
Faculty of Mechanical Engineering, University of Žilina, Univerzitná 8215/1, 010 26 Žilina, Slovakia

Casting with a disposable pattern is a method employed to produce intricate-shaped castings. This manufacturing technique falls into the near-net shape methods category, which ensures that the result-ing castings closely resemble the final components. Its primary application lies in industries where pre-cision and complex castings are of paramount importance. Typically, castings manufactured using this method utilize higher-cost materials. The focus of this study centres on the utilization of reverse engi-neering in the production, modification, and inspection of wax injection moulds during the casting pro-cess. Within the scope of this investigation, a non-contact method employing the Kreon arm with the Aqulion scanner was implemented. This method facilitated the generation of a digital scan, serving as the foundation for designing and validating the mould for subsequent practical application.

Keywords: Precision casting, Reverse engineering, 3D scanning, CT, Injection moulding
Grants and funding:

This research was funded by the University of Žilina project APVV 20-0561: “Research on the implementation of new measurement methods for the calibration of measurement systems for industrial metrology practice”, Kega project 033ŽU-4/2022: “Implementation of the language of geometric product specification in the field of coordinate 3D metrology”, and Visegrad Fund

Received: June 7, 2023; Revised: August 1, 2023; Accepted: September 1, 2023; Prepublished online: September 15, 2023; Published: December 6, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Bechný V, Matuš M, Joch R, Drbúl M, Holubják J, Czán A, et al.. Design of an Injection Mould Utilizing Experimental Measurements and Reverse Engineering. Manufacturing Technology. 2023;23(5):597-603. doi: 10.21062/mft.2023.072.
Download citation

References

  1. POURMOSTAGHIMI, V., HEIDARI, F., KHALILPOURAZARY, S., QAZANAI, M. (2023). Application of Evolutionary Optimization Techniques in Reverse Engineering of Helical Gears. In: Applied Study. Axioms, 12(3), pp. 252. https://doi.org/10.3390/axioms12030252 Go to original source...
  2. ĆIRIĆ, D., MILTENOVIĆ, A., MIHAJLOVIĆ, J., MIJAJLOVIĆ, M. (2021). Mechanical Design of the Bicycle Inner Tube Assembly Tool Based on the Reverse Engineering Methodology. In: International Conference on Machine and Industrial Design in Mechanical Engineering, pp. 207-215. Cham: Springer International Publishing. Go to original source...
  3. DURUPT, A., BRICOGNE, M., REMY, S., TROUSSIER, N., ROWSON, H., BELKADI, F. (2019). An extended framework for knowledge modelling and reuse in reverse engineering projects. In: Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 233, No. 5, pp. 1377-1389. https://doi.org/10.1177/0954405418789973 Go to original source...
  4. ANWER, N., MATHIEU, L. (2016). From reverse engineering to shape engineering in mechanical design. CIRP Annals, 65(1), 165-168.. https://doi.org/10.13140/RG.2.2.14297.93281 Go to original source...
  5. BUONAMICI, F., CARFAGNI, M., FURFERI, R., GOVERNI, L., LAPINI, A., VOLPE, Y. (2018). Reverse engineering of mechanical parts: A template-based approach. In: Journal of computational design and engineering, Vol. 5, No. 2, pp. 145-159. https://doi.org/10.1016/j.jcde.2017.11.009 Go to original source...
  6. BURSTON, M., SABATINI, R., GARDI, A., CLOTHIER, R. (2014.). Reverse engineering of a fixed wing unmanned aircraft 6-DoF model based on laser scanner measurements. In 2014 IEEE Metrology for Aerospace (MetroAeroSpace) (pp. 144-149). IEEE. https:// doi.org/10.1109/MetroAeroSpace.2014.6865910 Go to original source...
  7. KAŤUCH, P., DOVICA, M., SLOSARČÍK, S., KOVÁČ, J. (2012). Comparision of contact and contact-less measuring methods for form evaluation. In: Procedia Engineering, Vol. 48, pp. 273-279. https://doi.org/10.1016/j.proeng.2012.09.514 Go to original source...
  8. GASPARIN, S., TOSELLO, G., HANSEN, H. N., ISLAM, A. (2013). Quality control and process capa-bility assessment for injection-moulded micro mechanical parts. In: The International Journal of Advanced Manufacturing Technology, Vol. 66, pp. 1295-1303. https://doi.org/10.1007/s00170-012-4407-6 Go to original source...
  9. ONTIVEROS, S., YAGUE-FABRA, J. A., JIMÉNEZ, R., TOSELLO, G., GASPARIN, S., PIEROBON, A., HANSEN, H. N. (2012). Dimensional measurement of micro-moulded parts by computed tomography. Measurement Science and Technology, Vol. 23, No. 12, 125401. https://doi.org/10.1088/0957-0233/23/12/125401 Go to original source...
  10. DRBÚL, M., ŠAJGALÍK, M., ŠEMCER, J., CZÁNOVÁ, T., PETŘKOVSKÁ, L., ČEPOVÁ, L. (2014). Strojárska metrológia a kvalita povrchov vytvorených technológiami obrábania.
  11. CIOANA, C., TULCAN, A., GROZAV, I., COSMA, C. (2012). Scanning Strategies for Aluminium and Plastic Parts. In: Solid State Phenomena, Vol.188, pp. 406-411. Go to original source...
  12. SOONHWAN, H, JONGSUN, K. (2019). Injection mold design of reverse engineering using injection molding analysis and machine learning. Journal of Mechanical Science and Technology, Vol. 33, No.8, pp. 3803-3812 Go to original source...
  13. LI, Y., WANG, H., HE, J. (2021). Reverse engineering modeling of motor hood and injection mold design. In: Proceedings of the 6th International Conference on Intelligent Information Processing, pp. 121-126. Go to original source...
  14. CHANGMING, Z. (2010). Research on injection mold design based on Reverse Engineering. In: 2nd International Conference on Computer Engineering and Technology, Vol. 6, pp. 663-665. https://doi.org/10.4028/www.scientific.net/AMR.591-593.219 Go to original source...
  15. SAHLA, F., BEY, M., BENDIFALLAH, H. (2018). Mold Cavity Design Using Reverse Engineering Process.
  16. KRIVOŠ, E., PASTIRČÁK, R., LEHOCKÝ, P. (2014). Using of the reverse engineering method for the production of prototype molds by patternless process technology. In: Archives of Foundry Engineering, Vol.14. https://doi.org/10.2478/afe-2014-0048 Go to original source...
  17. ALI, S. (2015). La rétro-conception de composants mécaniques par une approche" concevoir pour fabriquer" (Doctoral dissertation, Université de Technologie de Troyes).
  18. STOKLASEK, P., MIZERA, A., MAŇAS, M., MAŇAS, D. (2016). Improvement of handle grip using reverse engineering, CAE and Rapid Prototyping. In: MATEC Web of Conferences 20th International Conference on Circuits, Systems, Communications and Computers (CSCC 2016). EDP Sciences. Go to original source...
  19. https://doi.org/10.1051/matecconf/20167602029 Go to original source...
  20. [19] VOICU, A. C., GHEORHE, I. G., BADITA, L. L., CIRSTOIU, A. (2013). 3D Measuring of complex automotive parts by multiple laser scanning. In: Applied Mechanics and Materials, Vol. 371, pp. 519-523. https://doi.org/10.4028/www.scientific.net/AMM.371.519 Go to original source...
  21. [20] MATUŠ, M., BECHNÝ, V., JOCH, R., DRBÚL, M., HOLUBJÁK, J., CZÁN, A., NOVÁK, M., ŠAJGALÍK, M. (2023). Geometric Accuracy of Components Manufactured by SLS Technology Regard-ing the Orientation of the Model during 3D Printing. In: Manufacturing Technology, Vol. 23, No. 2, pp. 233-240. DOI: 10.21062/mft.2023.027 Go to original source...
  22. [21] TIMKO, P., CZÁNOVÁ, T., CZÁN, A., SLABEJOVÁ, S., HOLBUJÁK, J., CEDZO, M. (2022). Analysis of Parameters of Sintered Metal Components Created by ADAM and SLM Technologies. In: Manufacturing Technology, Vol. 22, No. 4, pp. 347-355. DOI: 10.21062/mft.2023.008 Go to original source...
  23. [22] TIMKO, P., HOLUBJAK, J., BECHNÝ, V., NOVÁK, M., CZÁN, A., CZÁNOVÁ, T. (2023). Surface Analysis and Digitization of Components Manufactured by SLM and ADAM Additive Technologies. In: Manufacturing Technology, Vol. 23, No. 1, pp. 127-134. DOI: 10.21062/mft.2023.008 Go to original source...
  24. [23] KOZOVÝ, P., ŠAJGALÍK, M., DRBÚL, M., HOLUBJÁK, J., MARKOVIČ, J., JOCH, R. (2023). Identification of Residual Stresses after Machining a Gearwheel Made by Sintering Metal Powder. In: Manufacturing Technology, Vol. 23, No. 4. DOI: 10.21062/mft.2023.054 Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.