Manufacturing Technology 2023, 23(5):638-648 | DOI: 10.21062/mft.2023.101

Progress and Prospect of Ultrasonic Vibratory Cutting Research

Quyun Li ORCID..., Xinyuan Cai ORCID..., Wei Li ORCID..., Zhenhua Tan ORCID..., Canyu Yang ORCID...
College of Machinery and Transportation, Southwest Forestry University, Kunming 650224, China

Ultrasonic vibration cutting technology for processing difficult-to-cut materials proposed a new machining method to improve the cutting performance, is an effective measure to improve the surface quality and cutting efficiency, widely used in titanium alloys and other difficult-to-cut materials. This paper is based on the development of related technology research at home and abroad, first from one-dimensional ultrasonic vibration cutting, two-dimensional ultrasonic vibration cutting, three-dimensional ultrasonic vibration cutting three dimensions to high-speed ultrasonic vibration cutting to carry out the analysis, and then from each dimension of turning, drilling, grinding and milling and other different ways of cutting mechanism, cutting force, surface quality, device development, tool design and other directions of the systematic analysis and research. The analysis results show that ultrasonic vibration cutting technology provides new technical solutions and methods to solve the problems of low efficiency and low dimensional accuracy in processing difficult-to-cut materials by ordinary cutting technology, and can provide technical support for the processing of difficult-to-cut materials. Finally, it looks forward to the future trend of ultrasonic vibration cutting technology: in the future, the integration with five-axis machining technology, additive manufacturing technology, microscopic inspection technology, 5G communication technology and other cutting-edge technologies will be the development direction of ultrasonic vibration cutting technology.

Keywords: Ultrasonic vibration, Cutting, Cutting force, Surface quality, Devices and tools
Grants and funding:

This work was supported by the Science Research Fund Project of the Yunnan Provincial Department of Education (2022Y569)

Received: August 24, 2023; Revised: November 21, 2023; Accepted: November 30, 2023; Published: December 6, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Li Q, Cai X, Li W, Tan Z, Yang C. Progress and Prospect of Ultrasonic Vibratory Cutting Research. Manufacturing Technology. 2023;23(5):638-648. doi: 10.21062/mft.2023.101.
Download citation

References

  1. HAN, X., ZHANG, D., SONG, G., (2020). Review on current situation and development trend for ultrasonic vibration cutting technology. Materials Today Proceedings, Vol. 22, pp. 444-455. Go to original source...
  2. SHAMOTO, E., MORIWAKI, T., (1999). Ultraprecision Diamond Cutting of Hardened Steel by Appling Elliptical Vibration Cutting, Ann. CIRP, Vol. 48, pp. 441-444. Go to original source...
  3. JIA, D., LI, C., ZHANG, Y., YANG, M., ZHANG, X., LI, R., JI, H., (2019). Experimental evaluation of surface topographies of NMQL grinding ZrO2 ceramics combining multiangle ultrasonic vibration. The International Journal of Advanced Manufacturing Technology, Vol. 100, No. 1, pp. 457-473. Go to original source...
  4. YANG, Z., ZHU, L., LIN, B., ZHANG, G., NI, C., SUI, T., (2019). The grinding force modeling and experimental study of ZrO2 ceramic materials in ultrasonic vibration assisted grinding. Ceram International, Vol. 45, No. 7, pp. 8873-89. Go to original source...
  5. ZHANG, C., SONG, Y., (2019). Design and kinematic analysis of a novel decoupled 3D ultrasonic elliptical vibration assisted cutting mechanism. Ultrasonics, Vol. 95, pp. 79-94. Go to original source...
  6. BHADURI, D., SOO, S.L., ASPINWALL, D.K., NOVOVIC, D., BOHR, S., HARDEN, P., WEBSTER, J.A., (2017). Ultrasonic assisted creep feed grinding of gamma titanium aluminide using conventional and superabrasive wheels. CIRP Annals, Vol. 66, No. 1, pp. 341-344. Go to original source...
  7. JIANG, X., LIANG, H., LU, H., DAI, J., ZHANG, D., (2014). Research on ultrasonic elliptical vibratory milling of titanium alloy thin-walled parts. Journal of Military Engineering, Vol. 35, No. 11, pp. 1891-1897.
  8. KIM, G.D., LOH, B.G., (2011). Direct machining of micro patterns on nickel alloy and mold steel by vibration assisted cutting. International Journal of Precision Engineering and Manufacturing, Vol. 12, No. 4, pp. 583-588. Go to original source...
  9. CHERN, G.L., LIANG, J.M., (2007). Study on boring and drilling with vibration cutting. International Journal of Machine Tools and Manufacture, Vol. 47, No. 1, pp.133-140. Go to original source...
  10. ZHANG, Y.D., LV, R.F., (2004). Efficient and practical ultrasonic turning technology. Mechanical and Electrical Engineering, Vol. 21, No. 3, pp. 51-53.
  11. ZHA, C., ZHA, S. 2022. Theoretical and Experimental Study on the Influence of Ultrasonic Vibration on Contact Friction. Manufacturing Technology, 22, 367-76. Go to original source...
  12. SLABEJOVÁ, S., ŠAJGALÍK, M., TIMKO, P., KOZOVÝ, P., NOVÁK, M., CEDZO, M. 2023. Analysis of Cutting Forces during Machining with Additive-Produced Milling Head. Manufacturing Technology, 23, 254-9. Go to original source...
  13. TIMKO, P., HOLUBJAK, J., BECHNÝ, V., NOVÁK, M., CZÁN, A., CZÁNOVÁ, T. 2023. Surface Analysis and Digitization of Components Manufactured by SLM and ADAM Additive Technologies. Manufacturing Technology, 23, 127-34. Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.