Manufacturing Technology 2023, 23(6):846-852 | DOI: 10.21062/mft.2023.090

Structural and Mechanical Properties of CuZn30 Cartridge Brass in Real Production Conditions

Jan Luštinec ORCID...1, Miroslav Roško ORCID...2, Vladivoj Očenášek ORCID...1
1 SVÚM a. s., Tovární 2053, 250 88 Čelákovice. Czech Republic
2 Povrly Copper Industries a. s., Mírová 63, 403 32 Povrly. Czech Republic

The paper deals with the technology of production of deep-drawn plates from alpha brass CuZn30. Surface and hidden defects are often observed in these deep-drawn sheets. The research was aimed at reducing the occurrence of these defects and subsequently reducing scrap and increasing the quality of these metallurgical products with a tighter tolerance of the required structural and mechanical properties throughout the length and width of the sheets. The production technology was monitored from the preparation of the batch and casting parameters on the existing operating equipment, through the processing of the ingots by hot and cold rolling, to the recrystallization annealing of the sheets in coils in a hatch furnace and the subsequent continuous pickling and passivation of the final strips. Properties were monitored after each technological operation of production. Specifically, macrostructure, microstructure, microporosity, tensile mechanical properties, and hardness were analysed. The results showed that the chosen production technology has sufficient homogeneity of properties.

Keywords: Brass, CuZn30, Production Technology, Mechanical Properties, Structure
Grants and funding:

The results presented in this paper were created with the financial support of MPO ČR within the framework of the project CZ.01.1.02/0.0/0.0/20_321/0024505

Received: August 31, 2023; Revised: November 2, 2023; Accepted: November 13, 2023; Prepublished online: November 27, 2023; Published: December 22, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Luštinec J, Roško M, Očenášek V. Structural and Mechanical Properties of CuZn30 Cartridge Brass in Real Production Conditions. Manufacturing Technology. 2023;23(6):846-852. doi: 10.21062/mft.2023.090.
Download citation

References

  1. PÍŠEK, F., JENÍČEK, L., RYŠ, P. (1973). Nauka o materiálu I/3, ACADEMIA, Prague. ISBN 21-111-73
  2. SEDLÁČEK, V. (1979). Neželezné kovy a slitiny, SNTL - Státní nakladatelství technické literatury, Prague. ISBN 04-414-79
  3. SEDLÁČEK, V. (1957). Neželezné kovy - Hutnické výrobky a jejich použití, SNTL - Státní nakladatelství tech-nické literatury, Prague.
  4. OZGOWICZ, W., KALINOWSKA-OZGOWICZ, E., GRZEGORCZYK, B. (2010). The microstructure and mechanical properties of the alloy CuZn30 after recrystallizion annealing. In: Journal of Achievements in Materials and Manufacturing Engineering, Vol. 40, No. 1. ISSN 2300892X
  5. MUHAMMED, A., ABED, A., MUSTAFA, M. A. (2012). Effects of recrystallization temperature on the mechanical properties of CuZn30 alloy. In: First National Conference for Engineering Sciences (FNCES 2012), pp. 1 - 6. Iraq. ISBN 978-1-4673-5032-7 Go to original source...
  6. KLEIN, J. (2016). Recrystallization Behavior of 70/30 Brass. In: Physical and mechanical properties of materials, University of Illinois at Chicago. Chicago.
  7. BEZECNY, J., DUBEC, A. (2016). Metallographic and finite element evaluation of plastic deformation during the forming process of cartridge brass casings. In: Procedia Engineering, Vol. 136, pp. 137 - 142. ISSN 1877-7058 Go to original source...
  8. MUTLU, M., KARAKAŞ, A., KUŞDEMIR, H., KOLTAN, U. K., YALÇINKAYA, T. (2023) Flow form-ing and recrystallization behaviour of CuZn30 alloy. In: Materials Research Proceedings, Vol. 28, pp. 1021 - 1028. Go to original source...
  9. ČSN EN 1652 Měď a slitiny mědi - Desky, plechy, pásy a kotouče pro všeobecné použití (2000), Český normalizační institute, Prague.
  10. BAKER, H. (1999). ASM Handbook, Volume 3, Alloy Phase Diagrams, ASM International, Ohio. ISBN 0-87170-381-5
  11. HREN, I., LUŇÁK, M.., KUŚMIERCZAK, S. (2020). The formation and elimination of the negative influence of porosity on the properties of the alloy castings AlSi10Mg. In: Manufacturing Technology, Vol. 20, No. 2, pp. 170 - 176. ISSN 1213-2489 Go to original source...
  12. KUCHARIKOVÁ, L., TILLOVÁ, E., KRITIKOS, M., UHRÍČIK, M., ŠVECOVÁ, I. (2020). Usage of a non-destructive testing technology for assessment of porosity in aluminium casts alloys. In: Manufacturing Technology, Vol. 20, No. 5, pp. 632 - 638. ISSN 1213-2489 Go to original source...
  13. ZYSKA, A., BOROŃ, K. (2021). Comparison of the Porosity of Aluminum Alloys Castings Produced by Squeeze Casting.In: Manufacturing Technology, Vol. 21, No. 5, pp. 725 - 734. ISSN 1213-2489 Go to original source...
  14. WALKER, H. L. (1945). Grain sizes produced by recrystalization and coalescence in cold-rolled cartridge brass. In: University of Illinois Bulletin, Vol. 43, No. 21, University of Illinois Urbana.
  15. VANDER VOORT, G. (2015). Deformation and Annealing of Cartridge Brass. https://vacaero.com/information-resources/metallography-with-george-vander-voort/1440-deformation-and-annealing-of-cartridge-brass.html

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.