Manufacturing Technology 2023, 23(6):810-818 | DOI: 10.21062/mft.2023.104
FEM Simulation of the Flange Turning in the Production of Aluminium Aerosol Cans
- Institute of Manufacturing Science, University of Miskolc. Egyetemváros, 3515 Miskolc. Hungary
Even today, there is an ever-increasing demand for the production of aerosol cans made of aluminium, as the cosmetics and other propellant-enriched products stored in them reach more and more people with the development of humanity. The production of these packaging materials is primarily carried out by plastic forming operations. However, during the production process of aluminium aerosol cans, tools with a defined edge geometry also perform cutting operations. The processes taking place here affect the quality of the final product. In this paper, the procedure and results of finite element modelling of the flange turning of aluminium aerosol cans is presented. The structure of the finite element model is introduced, as well as the possibilities of considering the peculiarities of the process. Since the used pure aluminium (Al99.5) is considered a difficult-to-cut material, the machinability of aluminium and its alloys is also discussed.
Keywords: Aerosol can, Aluminium, Flange turning, Finite element simulation
Received: September 8, 2023; Revised: November 29, 2023; Accepted: December 1, 2023; Prepublished online: December 4, 2023; Published: December 22, 2023 Show citation
References
- NIEMIEC, K., FITRZYK, A., GRABOWIK, C. (2021). Methods of manufacture and innovations in steel aerosol cans' production. In: International Journal of Modern Manufacturing Technologies. Vol. 13, No. 3, pp. 96-104 DOI: 10.54684/ijmmt.2021.13.3.96.
Go to original source...
- KORES, S., TURK, J., MEDVED, J., VONČINA, M. (2016). Development of aluminium alloys for aero-sol cans. In: Mater. Tehnol. Vol. 50, No. 4, pp. 601-605 DOI: 10.17222/mit.2015.330.
Go to original source...
- GIULIANO, G., PARODO, G., POLINI, W., SORRENTINO, L. (2023). Cold Blow Forming of a Thin Sheet in AA8006 Aluminum Alloy. In: Manufacturing Technology. Vol. 23, No. 3, pp. 284-289 DOI: 10.21062/mft.2023.038.
Go to original source...
- PAGE, B. (2012). Rigid metal packaging. In: Packaging Technology. Elsevier. pp. 122-162 ISBN 978-1-84569-665-8.
Go to original source...
- ASM HANDBOOK COMMITTEE (1990). ASM Handbook Vol. 2: Properties and Selection: Nonferrous Alloys and Special-Purpose Materials. ASM International. Novelty, Ohio. p. 3470 ISBN 978-1-62708-162-7.
Go to original source...
- DESSIE, J.E., LUKACS, Z. (2022). Necking limit analysis of thin wall aerosol can. In: Pollack Periodica. Vol. 17, No. 2, pp. 48-53 DOI: 10.1556/606.2022.00558.
Go to original source...
- KIM, H.-S., RHIM, S.-H., HWANG, J.-I. (2020). Preliminary study of backward impact extrusion process design for aluminum air suspension tube using finite element analysis. In: Proceedings of the International Conference of Manufacturing Technology Engineers (ICMTE) 2020. pp. 61-61.
- SOBOTKA, J., SOLFRONK, P., KORECEK, D. (2020). Influence of Stress State on the Yield Strength of Aluminium Alloy. In: Manufacturing Technology. Vol. 20, No. 1, pp. 92-97 DOI: 10.21062/mft.2020.005.
Go to original source...
- ORANGI, S., ABRINIA, K., BIHAMTA, R. (2011). Process Parameter Investigations of Backward Extraction for Various Aluminum Shaped Section Tubes Using FEM Analysis. In: J. of Materi Eng and Perform. Vol. 20, No. 1, pp. 40-47 DOI: 10.1007/s11665-010-9655-8.
Go to original source...
- CARRILERO, M.S., MARCOS, M. (1996). On the Machinability of Aluminium and Aluminium Alloys. In: Journal of the Mechanical Behavior of Materials. Vol. 7, No. 3, pp. 179-194 DOI: 10.1515/JMBM.1996.7.3.179.
Go to original source...
- MICHNA, ©., HREN, I., CAIS, J., MICHNOVÁ, L. (2020). The Research of the Different Properties and Production Parameters having Influence on Deep-Drawing Sheets made of AlMg3 Alloy. In: Manufacturing Technology. Vol. 20, No. 3, pp. 347-354 DOI: 10.21062/mft.2020.035.
Go to original source...
- MILLS, B., REDFORD, A.H. (2011). Machinability of Engineering Materials. Springer Netherlands. Dordrecht. p. 174 ISBN 978-94-009-6633-8.
- JOEL, J., ANTHONY XAVIOR, M. (2018). Aluminium Alloy Composites and its Machinability studies; A Review. In: Materials Today: Proceedings. Vol. 5, No. 5, Part 2, pp. 13556-13562 DOI: 10.1016/j.matpr.2018.02.351.
Go to original source...
- MAJERÍK, J., DUBOVSKÁ, R., BA©KA, I., JAMBOR, J. (2018). Experimental Investigation and Measurement of Surface Roughness and Cutting Forces while Turning AlCu3MgMnPb Aluminium Alloy. In: Manufacturing Technology. Vol. 18, No. 1, pp. 66-71 DOI: 10.21062/ujep/55.2018/a/1213-2489/MT/18/1/66.
Go to original source...
- HORVÁTH, R., CZIFRA, Á., DRÉGELYI-KISS, Á. (2015). Effect of conventional and non-conventional tool geometries to skewness and kurtosis of surface roughness in case of fine turning of aluminium alloys with diamond tools. In: Int J Adv Manuf Technol. Vol. 78, No. 1-4, pp. 297-304 DOI: 10.1007/s00170-014-6642-5.
Go to original source...
- LAWAL, S.A., AHMED, A.M., LAWAL, S.S., UGHEOKE, B.I. (2016). Effect of HSS and Tungsten Car-bide Tools on Surface Roughness of Aluminium Alloy during Turning Operation. In: American Journal of Mechanical Engineering. Vol. 4, No. 2, pp. 60-64 DOI: 10.12691/ajme-4-2-3.
Go to original source...
- AKKURT, A. (2015). The effect of cutting process on surface microstructure and hardness of pure and Al 6061 aluminium alloy. In: Engineering Science and Technology, an International Journal. Vol. 18, No. 3, pp. 303-308 DOI: 10.1016/j.jestch.2014.07.004.
Go to original source...
- SONGMENE, V., KHETTABI, R., ZAGHBANI, I., KOUAM, J., DJEBARA, A. (2011). Machining and Machinability of Aluminum Alloys. In: Aluminium Alloys, Theory and Applications. IntechOpen. London. pp. 377-400 ISBN 978-953-307-244-9.
Go to original source...
- OKOKPUJIE, I.P. et al. (2017). Experimental and Mathematical Modeling for Prediction of Tool Wear on the Machining of Aluminium 6061 Alloy by High Speed Steel Tools. In: Open Engineering. Vol. 7, No. 1, pp. 461-469 DOI: 10.1515/eng-2017-0053.
Go to original source...
- BÁTORFI, J.G., ANDÓ, M. (2020). Study of Parameters during Aluminum Cutting with Finite Element Method. In: Period. Polytech. Mech. Eng. Vol. 64, No. 2, pp. 136-144 DOI: 10.3311/PPme.14641.
Go to original source...
- ROY, P., SARANGI, S.K., GHOSH, A., CHATTOPADHYAY, A.K. (2009). Machinability study of pure aluminium and Al-12% Si alloys against uncoated and coated carbide inserts. In: International Journal of Refractory Metals and Hard Materials. Vol. 27, No. 3, pp. 535-544 DOI: 10.1016/j.ijrmhm.2008.04.008.
Go to original source...
- ASTAKHOV, V.P. (2010). Springer Series in Advanced Manufacturing Geometry of Single-point Turning Tools and Drills. Springer. London. p. 565 ISBN 978-1-84996-052-6.
Go to original source...
- DAVIM, J.P. ed (2012). Statistical and Computational Techniques in Manufacturing. Springer. Berlin, Heidelberg. ISBN 978-3-642-25858-9.
Go to original source...
- PARIHAR, R.S., SAHU, R.K., SRINIVASU, G. (2017). Finite Element Analysis of Cutting Forces Generated in Turning Process using Deform 3D Software. In: Materials Today: Proceedings. Vol. 4, No. 8, pp. 8432-8438 DOI: 10.1016/j.matpr.2017.07.188.
Go to original source...
- MATHIVANAN, A., SWAMINATHAN, G., SIVAPRAKASAM, P., SUTHAN, R., JAYASEELAN, V., NAGARAJ, M. (2022). DEFORM 3D Simulations and Taguchi Analysis in Dry Turning of 35CND16 Steel. In: Advances in Materials Science and Engineering. Vol. 2022, pp. 1-10 DOI: 10.1155/2022/7765343.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.