Manufacturing Technology 2023, 23(6):837-845 | DOI: 10.21062/mft.2023.105
Influence of Thermomechanical Processing Parameters on Selected Properties of B-post Made of 22MnB5 Steel
- Faculty of Mechanical Engineering, J. E. Purkyne University in Usti nad Labem. Pasteurova 3334/7, 400 01 Usti nad Labem. Czech Republic
With regard to the current economic situation, which deals primarily with energy prices, companies are trying to find reserves within individual technologies. The automotive industry is still a very important industry. One of the ways to improve the material properties of a body part is thermomechanical processing. This is how the B-pillar, which serves as a safety structural element of the car, was processed. The presented article aims to investigate the influence of selected thermomechanical processing parameters on the resulting properties of a B-pillar made of high-strength steel 22MnB5. At the same time, energy saving in the given production process should be used in such a way that it is not at the expense of the quality of the component. Three kinds of experimental production processes with different parameters of thermomechanical processing of steel were proposed for scientific investigation. Based on these proposed processes, several pieces of B-pillars were produced and subjected to further investigation. Changes in material properties were monitored using hardness measurements and subsequently the resulting microstructure of the material was examined for each experimental post.
Keywords: Thermomechanical processing, Steel 22MnB5, Analysis, Microstructure
Grants and funding:
Supported by the project SGS 48207 15 2027 01 at Jan Evangelista Purkyne University in Usti nad Labem
Received: August 30, 2023; Revised: November 28, 2023; Accepted: December 8, 2023; Prepublished online: December 14, 2023; Published: December 22, 2023 Show citation
References
- CHANG, Y., ZHENG, G., LI, X., JIN, C., WANG, C.,DONG, H. (2021). Evaluation on the formability of the third-generation automotive medium-Mn steel based on experiment and simulation. In. International Journal of Advanced Manufacturing Technology, Volume 117, Issue 3-4, Page 1015-10, ISSN 0268-3768.
Go to original source...
- JANDA, T. (2018). Use of Metallographic Analysis for Evaluating Microstructures in Quenched and Tempered High-Strength Steel. In. Manufacturing Technology. Vol. 18, No. 1, ISSN 1213-2489.
Go to original source...
- RAZMPOOSH, M. H., MACWAN, A., BIRO, E., ZHOU, Y. (2020). Microstructure and dynamic ten-sile characteristics of dissimilar fiber laser welded advanced high strength steels. In. Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing. Volume 773, ISSN 0921-5093.
Go to original source...
- YUAN, CH., LI, S., HUANG, J., LIN, X., BIAN, X., CHEN, J. (2021). Effect of hierarchical martensitic microstructure on fatigue crack growth behavior of ultra-high strength hot stamping steel. In. Materials Characterization. Volume 174, ISSN 1044-5803.
Go to original source...
- KRAWCZYK, J., et al. (2021). State of Strain and Development of Microstructure of 22MnB5 Steel and Al-Si Coating during Deep Drawing of Automotive B Pillar. In: Arch. Metall. Mater. 66, 2, pp. 601-608. ISSN 1733-3490.
Go to original source...
- PACKO, M., YOU, K. H., KIM, H.-K. (2021) A Study on the Effect of Process and Material Variables on the Hot Stamping Formability of Automotive Body Parts. In: Metals 2021, 11, 1029. eISSN 2075-4701.
Go to original source...
- BUBLIKOVA, D., JIRKOVA, H., STEHLIK, A, JENIČEK. ©. (2023). Effect of Temperature and De-formation on the Stability of Retained Austenite in Closed-Die Forgings from High-Strength Martensitic Manganese-Silicon Steels. In. Manufacturing Technology. Vol. 23, No. 3. ISSN 1213-2489. e-ISSN 2787-9402
Go to original source...
- BURDOVÁ, K., JIRKOVÁ, H., KUČEROVÁ, L., ZETKOVÁ, I., MACH, J. (2022). Effects of Heat Treatment on Additively Manufactured 316L Stainless Steel. In. Manufacturing Technology. Vol. 22, No. 3, pp. 261-266, ISSN 1213-2489.
Go to original source...
- LI, S., ZHOU, L., WU, X., ZHANG, Y., LI, J. (2016). The Influence of Thermal Conductivity of Die Material on the Efficiency of Hot-Stamping Process. In. Journal of Materials Engineering and Performance. Volume 25, Issue 11, Page 4848-4867, ISSN 1059-9495.
Go to original source...
- PARK, A., NAM, J. H., KIM, M., JANG, I. S., LEE, Y. K. (2020). Evaluations of tensile properties as a function of austenitizing temperature and springback by V-bending testing in medium-Mn steels. In. Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing. Volume 787, ISSN 0921-5093.
Go to original source...
- SHUO-SHUO, L., HAI-WEN, L. (2021) Medium-Mn steels for hot forming application in the automotive industry. In. International Journal of Minerals, Metallurgy and Materials. Volume 28, Number 5, May 2021, pp. 741-753, ISSN 1674-4799,
Go to original source...
- SINGH, A. K., NARASIMHAN, K. (2021). Effect of strain rate on formability of 22MnB5 steel during hot stamping process. In. International Deep-Drawing Research Group Conference. Volume 1157, ISSN 1757-8981.
Go to original source...
- ZHUANG, W., WANG, P., XIE, D., SHI, H. (2019). Experimental study and a damage model approach to determine the effect of hot forming deformation on the service performance of 22MnB5 steel. In. Journal of Manufacturing Processes. Volume 47, Page 10-21, ISSN 1526-6125.
Go to original source...
- KUSMIERCZAK, S., SLAVIK, M. (2018). Analysis of Al-Si layer on steel sheet during thermo mechanical processing using microscopic methods. In: Manufacturing Technology, Vol. 18, No. 5, pp. 769-774. CZ, ISSN 1213-2489.
Go to original source...
- MIN, J. LIN, J. MIN, Y., LI, F. (2012). On the ferrite and bainite Transformation in isothermally de-formed 22MnB5 Steels. In. Materials Science and Engineering A-Structural Materials Properties Microstructure and Processing. Volume 550, Page 375-387, ISSN 0921-5093.
Go to original source...
- OKAYASU, M., YANG, L. (2019) Influence of microstructure on the mechanical properties and hydrogen embrittlement characteristics of 1800 MPa grade hot-stamped 22MnB5 steel. In. J Mater Sci. Vol. 54, pp. 5061-5073, ISSN 0957-4522.
Go to original source...
- ZHOU, P.W., YAN, Z.I., WANG, K., LIU, T. et al. (2023). The influence of adding niobium and vanadium on hydrogen diffusion in 22MnB5 hot stamping steel. In. Journal of Iron and Steel Research International. ISSN 1006-706X, eISSN 2210-3988.
Go to original source...
- ZHOU, Q., GUO, P., QIN, F. (2022). Stress Response Behavior, Microstructure Evolution and Constitutive Modeling of 22MnB5 Boron Steel under Isothermal Tensile Load. In. Metals. Volume 12, Issue 6, eISSN 2075-4701.
Go to original source...
- CAVUSOGLU, O., CAVUSOGLU, O., YILMAZOGLU, A. G., UZEL, U., AYDIN, H., GURAL, A. (2020). Microstructural features and mechanical properties of 22MnB5 hot stamping steel in different heat treatment conditions. In. Journal of Materials Research and Technology. Volume 9, Issue 5, Page 10901-10908, ISSN 2238-7854.
Go to original source...
- HORN, A., MERKLEIN, M. (2021). Investigation of the Microstructural Evolution during Hot Stamping of Carburized Complex Phase Steel by Laser-Ultrasonics. In. Materials. Volume 14, Issue 8, eISSN 1996-1944.
Go to original source...
- JANDA, T. (2018). Use of Metallographic Analysis for Evaluating Microstructures in Quenched and Tempered High-Strength Steel. In. Manufacturing Technology. Vol. 18, No. 1, ISSN 1213-2489.
Go to original source...
- KUČEROVA, L., JANDOVA, A., RUBE©OVA, K. (2019). Microstructure Analysis and Mechanical Properties of Low Alloyed Steel with Retained Austenite Obtained by Heat Treatment. In. Manufacturing Technology. Vol. 19, No. 2.pp.243-247, ISSN 1213-2489.
Go to original source...
- KUSMIERCZAK, S., NAPRSTKOVA, N., MICIAN, M. (2020). Usage of Microscopic Methods in Analysis of Non-Conforming Nickel Alloy Products. In. 19th International Scientific Conference Engineering for Rural Development, pp. 1208-1213, ISSN 1691-3043, eISSN 1691-5976
Go to original source...
- TAVODOVA, M., NAPRSTKOVA, N., HNILICOVA, M., BENO, P. (2020). Quality Evaluation of Welding Joints by Different Methods. In. FME Transactions, Volume 48, Issue 4, Page 816-824, ISSN 1451-2092, eISSN 2406-128X.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.