Manufacturing Technology 2023, 23(6):819-826 | DOI: 10.21062/mft.2023.106
Methodology of Analysis of Fibre Sedimentation in HPC mixtures
- 1 Klokner Institute, Czech Technical University in Prague. Šolínova 7, 166 08 Prague 6. Czech Republic
- 2 Faculty of Mechanical Engineering, Czech Technical University in Prague. Technická 4, 166 07 Prague 6. Czech Republic
The aim of this work is to propose a methodology for evaluating inhomogeneity due to the sedimenta-tion of fibres in High-Performnce Concrete (HPC) mixtures. HPC mixtures makes better mechanical-physical properties than ordinary concrete. To achieve higher strengths, the fine-grained matrix is rein-forced with the reinforcement – fibres. The type of used fibres and their homogenization in mixture has an influence on the final mechanical properties of HPC mixture. Four concrete mixtures with same com-ponent proportion was chosen for experiments. Water was the only one component, that was changing in mixture recipes. Steel fibres with a ratio of the diameter to length = 0.3/20 were used as reinforcement. The fibre volume in mixture was 1.5 %. The microscopy analysis was used for evaluation of the fibre dis-tribution in the test specimens. It was obtained, that the concentration of the fibres increases with dis-tance from the surface to the bottom of the HPC structure and this non-homogeneity increases with higher water dosage. The dependence of sedimentation of fibres on composition of HPC mixtures can be used for evaluation and optimization of final mechanical properties of the HPC structures.
Keywords: HPC mixtures, Steel fibres, Sedimentation, Fibres distribution
Grants and funding:
This work has been supported by a research project of the Grant Agency of Czech Republic No. 21-24070S Model of fibre segregation in dependence on rheological properties of fresh HPC
Received: September 22, 2023; Revised: December 10, 2023; Accepted: December 14, 2023; Prepublished online: December 14, 2023; Published: December 22, 2023 Show citation
References
- KMITA, A. (2000). A new generation of concrete in civil engineering. In: Journal of Materials Processing Technology, Vol. 106, No. 1-3, pp. 80 - 86. Elsevier B.V. ISSN 0924-0136
Go to original source...
- Ductal [online]. Holcim Techology Ltd. (cited November, 19, 2023). Available from: https://www.ductal.com/en
- MAZZACANE, P., RICCIOTTI, R. and TEPLY, F. (2009). LA Passerelle des Anges. In: Workshop on Ultra High-Performance Fibre- Reinforced Concrete (UHPFRC) [online]. pp. 1 - 11. AFGC and fib. (cited March 14, 2020). Available: http://www.planete-tp.com/IMG/pdf/2UHPFRC-20091117- 18_Marseille_cle07c191.pdf
- Lávka pro pěší a cyklisty v Táboře-Černých mostech [online]. KŠ Prefa. ©2020. (cited November 19, 2023). Available from: https://ksprefa.cz/portfolio/lavka-pro-pesi-a-cyklisty-v-prostoru-cernych-mostu-v-tabore/
- Štvanická lávka [online]. Kloknerův ústav ČVUT v Praze ©2020. (cited November 19, 2023) Avalaible from: https://www.klok.cvut.cz/stvanicka-lavka/#pll_switcher
- AFGC (2013). Ultra High-Performance Fibre-Reinforced Concretes, Recommandations. Paris, France: Association Francaise de Génie Civil (AFGC).
- YOKOTA, H., ROKUGO, K., SAKATA, N. (2007). Recommendations for Design and Construction of High Per-formance Fiber Reinforced Cement Composites with Multiple Fine Cracks (HPFRCC). In: Concrete Engineering Series 82. 113 p. Japan Society of Civil Engineers.
- KOLÍSKO, J., BOUŠKA, P., ČÍTEK, D., HUŇKA, P., RYDVAL, M. and VOKÁČ, M. (2015). Metodika 1 - Metodika pro návrh UHPC a pro materiálové zkoušky. Czech Technical University, Klokner Institute. 32 p.
- fib special activity group, New Model Code, et al. (2013). fib Model Code for Concrete Structures 2010. Ernst & Sohn, Wiley. doi:10.1002/9783433604090
Go to original source...
- RYVOLOVÁ, M., SVOBODOVÁ, L., BAKALOVA, T., VOLESKÝ, L (2021). Influence of Basic Environment of Geopolymer Composites on Degradation Rates of E and AR Type Glass Fibers. In: Manufacturing Technology, Vol. 21, No. 2, pp. 246-253. J. E. Purkyne University in Ústí nad Labem, Czech Republic. ISSN: 1213-2489
Go to original source...
- MAJKO, J., VAŠKO, M., HANDRIK, M., SÁGA, M. (2023). Challenges in Tensile Testing of Thermo-plastic Composites Reinforced with Chopped Carbon Fibre Produced by Fused Filament Fabrication Method. In: Manufacturing Technology, Vol. 23, No. 2, pp. 216-224. J. E. Purkyne University in Ústí nad La-bem, Czech Republic. ISSN: 1213-2489
Go to original source...
- MOSTOFINEJAD, D., BAHMANI, H., AFSHAR, J. (2023). Prediction of Mechanical Properties of High-Performance Concrete (HPC) Reinforced with Steel Fibers. In: Iranian Journal of Science and Technology, Transactions of Civil Engineering, Vol. 47, pp. 1971-1993. Shiraz University. ISSN 2228-6160
Go to original source...
- MA, Y. Q. (2013). Experimental Study on Mechanical Properties of Steel Fiber Reinforced High Performance Concrete. In: Advanced Materials Research, Vol. 859, pp. 56-59. Scientific.Net. ISSN: 1022-6680
Go to original source...
- ABDULHAMEED U. A. (2019). Statistical Evaluation of Compressive Strength in High Performance Concrete (HPC) with Steel Fiber Addition. In: Sustainable Structures and Materials, Vol. 2, No .1, pp. 14-31. ISSN: 2616-4779
- SHEHAB EL-DIN, H. K., MOHAMED, H. A., KHATER, M., AHMED, S. (2016). Effect of Steel Fibres on Behavior of Ultra High-Performance Concrete. In: International Interactive Symposium on Ultra-High-Performance Concrete. 10 p. doi: https://doi.org/10.21838/uhpc.2016.11
Go to original source...
- LAU, A., ANSON, M. (2006). Effect of high temperatures on high performance steel fibre reinforced concrete. In: Cement and Concrete Research, Vol. 36, No. 9, pp. 1698-1707. Elsevier Ltd. ISSN: 0008-8846
Go to original source...
- XU, L., WU, F., CHI, Y., CHENG, P., ZENG, Y., CHEN, Q. (2019). Effects of coarse aggregate and steel fibre contents on mechanical properties of high-performance concrete. In: Construction and Building Materials, Vol. 206, pp. 97-110. Elsevier Ltd. ISSN: 0950-0618
Go to original source...
- ZHANG, W., ZHENG, M., ZHU, L., REN, Y., LV, Y. (2022). Investigation of steel fiber reinforced high-performance concrete with full aeolian sand: Mix design, characteristics and microstructure. In: Construction and Building Materials, Vol. 342, Part B, 12 p. Elsevier Ltd. ISSN: 1879-0526 (online)
Go to original source...
- ALI, B., KURDA, R., AHMED, H., ALYOUSEF, R. (2022). Effect of recycled tyre steel fiber on flexural toughness, residual strength, and chloride permeability of high-performance concrete (HPC). In: Journal of Sustainable Cement-Based Materials, Vol. 12, No. 2, pp. 141-157. Taylord & Francis Group. ISSN: 2165-0373
Go to original source...
- KALIFA, P., CHÉNÉ, G., GALLÉ, C. (2001). High-temperature behaviour of HPC with polypropylene fibres: From spalling to microstructure. In: Cement and Concrete Research, Vol. 31, No. 10, pp. 1487-1499. Elsevier Ltd. ISSN: 0008-8846
Go to original source...
- GUERRINI, G. L., CATTANEO, S., DHIR, R. K., NEWLANDS, M.D., WHYTE, A. (2015). Residual Properties of Hybrid Polypropylene-Steel Fibre Reinforced HPC Exposed to High Temperatures. In: Application of Codes, Design and Regulations: Proceedings of the International Conference held at the University of Dundee, Scotland, UK on 5-7 July 2005
- XIAO, J., FALKNER, H. (2006). On residual strength of high-performance concrete with and without polypropylene fibres at elevated temperatures. In: Fire Safety Journal, Vol. 41, No. 2, pp. 115-121. Elsevier Ltd. ISSN: 0379-7112
Go to original source...
- SMARZEWSKI, P. (2019). Influence of basalt-polypropylene fibres on fracture properties of high-performance concrete. In: Compossite Structures, Vol. 209, pp. 23-33. Elsevier Ltd. ISSN: 1879-1085
Go to original source...
- ALOMAYRI, T.S., ALI, B. (2023). Investigating the load-deflection behaviour and drying shrinkage resistance of HPC reinforced using different cellulose fibres. In: Journal of Building Engineering, Vol. 73, 15 p. Elsevier Ltd. ISSN: 2352-7102 (online)
Go to original source...
- SMARZEWSKI, P. (2020). Flexural toughness evaluation of basalt fibre reinforced HPC beams with and without initial notch. In: Composite Structures, Vol. 235, 12 p. Elsevier Ltd. ISSN: 1879-1085
Go to original source...
- RAHIMI, M., HISSEINE, O.A., TAGNIT-HAMOU, A. (2022). Effectiveness of treated flax fibers in improving the early age behavior of high-performance concrete. In: Journal of Building Engineering. Vol. 45, 9 p. Elsevier Ltd. ISSN: 2352-7102 (online)
Go to original source...
- ALOMAYRI, T., ALI., B., RAZA, S.S., EL HACHEM, C., AHMED, H., AZAB, M. (2023). Effect of binder strengthening using micro-silica on mechanical and absorption characteristics of HPC reinforced with reclaimed jute fibres. In: Case Studies in Construction Materials, Vol. 18, 13 p. Elsevier Ltd. ISSN: 2214-5095 (online)
Go to original source...
- ALI, M., ELSAYED, M., TAYEH, B. A., MAGLAD, A. M., EL-AZIM, A.A. (2023). Effect of hybrid steel, polypropylene, polyvinyl alcohol, and jute fibers on the properties of ultra-high performance fiber reinforced concrete exposed to elevated temperature. In: Structural Concrete. Journal of the fib. September 2023. Fib CEB-FIB. ISSN: 1464-4177.
Go to original source...
- CZAJKOWSKA, A., INGALDI, M. (2022). Influence of Steel Fibers Content on Selected Mechanical Properties - Experimental Tests. In: Manufacturing Technology, Vol. 22, No. 3, pp. 267-278. J. E. Purkyne University in Ústí nad Labem, Czech Republic. ISSN: 1213-2489
Go to original source...
- WANG, D., JU, Y., SHEN, H., XU, L. (2019). Mechanical properties of high-performance concrete reinforced with basalt fiber and polypropylene fiber. In: Construction and Building Materials, Vol. 197, pp. 464-473. Elsevier Ltd. ISSN: 0950-0618
Go to original source...
- YANG, J., CHEN, B., SU, J., XU, G., ZHANG, D., ZHOU, J. (2022). Effects of fibers on the mechanical properties of UHPC: A review. In: Journal of Traffic and Transportation Engineering (English Edition), Vol. 9, No. 3, pp. 363-387. Periodical Offices of Chang'an University. Publishing services by Elsevier B.V. on behalf of KeAi Communications Co. Ltd. ISSN: 2095-7564
Go to original source...
- SHARMA, R., JANG, J.G., BANSAL, P:P. (2022). A comprehensive review on effects of mineral admixtures and fibers on engineering properties of ultra-high-performance concrete. In: Journal of Building Engi-neering, Vol. 45, 20 p. Elsevier Ltd. ISSN: 2352-7102 (online)
Go to original source...
- RYDVAL, M., HUŇKA, P., KOLÍSKO, J. (2015). Production and properties of functionally graded UHPFRC beams. In: Advanced Materials Research, Vol. 1106, pp. 156-159, doi: 10.4028/www.scientific.net/AMR.1106.156
Go to original source...
- KABELE, P., SAJDLOVÁ, T., RYDVAL, M., KOLÍSKO, J. (2015) Modeling of High-Strength FRC Structural Elements with Spatially Non-Uniform Fiber Volume Fraction. In: Journal of Advanced Concrete Technology, Vol. 13, pp. 311-324. doi: 10.3151/jact.13.311
Go to original source...
- KABELE, P., SAJDLOVÁ, T., RYDVAL, M. (2016). DIC analysis of shear failure in functionally graded cementitious composite beams. [Online]. (cited November 19, 2023). Available: http://isit.si/das2016
- RYDVAL, M., KOLÍSKO, J. (2015). Ohybová únosnost desek ztraceného bednění vyrobených z UHPFRC a vliv distribuce ocelových vláken. [Online] Bet. TKS. No. 2/2015, pp. 34-37, Apr. 2015. Available: http://www.betontks.cz/sites/default/files/BETON_2-15.pdf
- DOSTÁL, M., MORAVEC, J., JIROUT, T., RYDVAL, M., HURTIG, K, JIROUTOVÁ, D. (2023). Model fluids substituting fresh UHPC mixtures flow behaviour. In: Archive of Applied Mechanics, Vol. 93, No. 7, 14 p. Spring Nature. ISSN: 0939-1533
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.