Manufacturing Technology 2023, 23(6):999-1005 | DOI: 10.21062/mft.2023.114

Optimization and Experiment of Linear Motor Platform Servo Control Algorithm

Shu Wang ORCID...1, Xiaoyan Wu ORCID...1,2
1 School of Mechanical and Electrical Engineering, Hubei Polytechnical University, 16Guilin Rd.(N), Huangshi, Hubei, China
2 Hubei Key Laboratory of Intelligent Convey Technology and Device, Hubei Polytechnical University, 16Guilin Rd. (N), Huangshi, Hubei, China

In view of the linear motor servo control system has the advantages of high speed, high response characteristics, in order to adapt to the motion precision, response speed and stability requirements of high precision movement occasions, combined with fuzzy control theory, the design of linear motor platform servo control system fuzzy adaptive PID control algorithm. At the same time, based on LabVIEW software, combined with USB-6009 data acquisition card produced by NI company, the experimental platform for linear motor motion control is designed. Through simulation experiments, the position tracking accuracy, disturbance resistance and response speed of linear motor can be greatly improved. The experimental results achieve the expected control effect, which provides a control method for related research. Therefore, the fuzzy adaptive PID composite control can combine the advantages of both and improve the control effect.

Keywords: Linear motor, Servo system, Control algorithm, Adaptive, Theory of ambiguity
Grants and funding:

This work was supported by Key Projects of Hubei Provincial Natural Science Joint Innovation Fund (2023AFD002)

Received: September 14, 2023; Revised: December 15, 2023; Accepted: December 19, 2023; Prepublished online: December 19, 2023; Published: December 22, 2023  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Wang S, Wu X. Optimization and Experiment of Linear Motor Platform Servo Control Algorithm. Manufacturing Technology. 2023;23(6):999-1005. doi: 10.21062/mft.2023.114.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. JI, Y., SUN, Q., (2022). Stabilization of carboxymethyl cellulose on foam concrete. International Journal of Molecular Science, Vol. 23, No. 24, pp. 15473. Go to original source...
    2. Performance characterization of Ji Y, Kim Y J, Jia Y. Plain concrete and CFRP bonded concrete under sulfuric acid action. Materials and Design, 2021197:109176.
    3. FAN, H., CHEN, H., (2021). Linear motor control system based on Smiht predictor. Applied Science and Technology, Vol. 29, No. 5, pp. 27-29.
    4. SHU, Q., (2022). Predictive Control Systems and Their Applications. Beijing: Mechanical Industry Press.
    5. K YOSHIDA, H., (2022). Deeooupled control method for floating and propulsion amphibious trains marine express. Memories of the Engineering Department at Kyushu University, Vol. 55, No. 4, pp. 467-489.
    6. ZOU, J., (2022). Research on Control Strategy of Permanent Magnet Linear Synchronous Motor. Zhejiang University.
    7. SEITZ, H., RIEDER, W., IRSEN, S., ETC. (2021). 3D printing of porous ceramic scaffolds for bone tissue engineering. Journal of Biomedical Materials Research B Appl Biometer, Vol. 74, No. 2, pp. 782-788. Go to original source...
    8. DHAOADI, R., (2022). Design and Implementation of an Extended Kalman Filter for State Estimation of Permanent Magnet Synchronous Motors. IEEE Journal of Power Electronics, Vol. 6, No. 3, pp. 491-497. Go to original source...
    9. NOROTTE, C., MARGA, F.S., NIKLASON, L.E., ETC. (2020). Stentless vascular tissue engineering using bioprinting. Biomaterials, Vol. 30, No. 30, pp. 5910-5917. Go to original source...
    10. SMITH, C.M., ROY, T.D., BHALKIKAR, A., ETC. (2021). Design titanium and polycaprolactone structures for the biocompatible interface between the body and prosthetics. Tissue Engineering Part A, Vol. 16, No. 2, pp. 717-724. Go to original source...
    11. AUTUMN, F., (2022). Overview of Control Strategies for Permanent Magnet Synchronous Linear Motors. Micro and Special Motors, Vol. 10, pp. 39-43.
    12. BOWLES, R., (2021). Examining Our Past from London with Yesterday's Tomorrow Project: Eric Leswett. Proc. IEEE, Vol. 89, No. 2, pp. 214-216. Go to original source...
    13. SUN, W., (2021). A Rule Self tuning Fuzzy Controller Based on Neural Networks and Its Application in AC Servo Systems. CSEE Meeting Minutes, Vol. 21, No. 7, pp. 15-17.
    14. MIROSLAV, V., (2020). Sensorless nonlinear control of induction motors based on artificial neural networks. IEEE Trans. Energy Conversion, Vol. 20, No. 3, pp. 520-528.
    15. LAISEN, F., (2022). Induction driven monitoring based on neural networks. IEEE International Conference, Industrial Electronics, Control Instrumentation, 859-863.
    16. ZENG, G., (2022). Fuzzy Control Theory and Engineering Applications. Huazhong University of Science and Technology Press.
    17. YE, Y., CHEN, K., (2021). PID control and fuzzy control of linear motors. Journal of China Electrotechnical Society, Vol. 6, No. 3, pp. 21-24.
    18. GOLD. (2022). High precision positioning of linear permanent magnet synchronous motors for surface mount device placement systems. Power Conversion, Vol. l, No. l, pp. 37-42.
    19. SHAMES, G., (2022). The development of a high-speed CNC cutting machine using a linear motor. Material Processing Technology, Vol. 166, pp. 321-329. Go to original source...
    20. YOSHIDA, K., (2022). Decoupling control method for suspension and propulsion of amphibious trains. Memories from Kyushu University School of Engineering, Vol. 55, No. 4, pp. 467-489.
    21. QUADRANI, P., (2022). Using rapid prototyping technology to manufacture high-resolution 3D scaffold models for engineering tissues. Medical Bioengineering Computing, Vol. 43, No. 2, pp. 196-199. Go to original source...
    22. GUO, H., KANG, M., ZHOU, W. 2021. Prediction of Surface Roughness and Optimization of Process Parameters for Slow Tool Servo Turning. Manufacturing Technology, 21, 616-26. Go to original source...
    23. ZHOU, W., KANG, M., GUO, H. 2022. Development of a Surface Roughness Prediction Model for Slow Tool Servo Turning Machining. Manufacturing Technology, 22, 111-22. Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content