Manufacturing Technology 2024, 24(1):148-153 | DOI: 10.21062/mft.2024.001

Influence of Technological Parameters on the Cutting Temperature during Trochoidal Milling

Kamil Piotr Waszczuk ORCID...
Wroclaw University of Technology and Science, Faculty of Mechanical Engineering, Lukasiewicza 5, 50-370 Wroclaw, Poland

The aim of the article was to present the results of cutting temperature measurements during trochoidal milling. The investigated material was 145Cr6 (50 HRC). Three trochoidal paths were used: A– described by movement circle, B– described by arcs and straight lines, C– described by short lines between a lot of points. The main conclusions include: similar values of cutting tem-peratures when using paths A and C (differences between the values of about 5%), the use of a trochoidal path type B enables a significant reduction of the cutting temperature. During tro-choidal milling, the maximum temperature values were about 420ºC.

Keywords: Trochoidal milling, Hard machining, Cutting temperature, Tool path

Received: May 15, 2023; Revised: November 15, 2023; Accepted: January 2, 2024; Prepublished online: January 23, 2024; Published: February 23, 2024  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Waszczuk KP. Influence of Technological Parameters on the Cutting Temperature during Trochoidal Milling. Manufacturing Technology. 2024;24(1):148-153. doi: 10.21062/mft.2024.001.
Download citation

References

  1. DUBOVSKA, R., MAJERIK, J., BASKA, I., JAMBOR J. (2015). Investigation of cutting temperature during AlCu3MgMnPb aluminium alloy turning, Vol. 15, pp. 357-362. Manufacturing Technology, Czech Republic. ISSN 1213-2489 Go to original source...
  2. KUCZMASZEWSKI, J., ZAGÓRSKI, I. (2013) Methodological problems of temperature measurement in the cutting area during milling magnesium alloys, Vol. 4, pp. 26-33. Management and Production Engineering Review, Poland. ISSN 2080-8208 Go to original source...
  3. LE GOZ, G., MARINESCU, M., DEVILLEZ, A., DZUDZINSKI, D., VELNOM, L. (2012) Measuring temperature of rotating cutting tools: Application to MQL drilling and dry milling of aerospace alloys, Vol. 36, pp. 434-441.Applied Thermal Engineering, United Kingdom. ISSN 1873-5606 Go to original source...
  4. MING, C., FANGHONG, S., HAILI W., RENWEI, Y., ZHENGHONG, Q., SHUQIAO, Z. (2003) Experimental research on the dynamic characteristics of the cutting temperature in the process of high-speed milling, Vol. 138, pp. 468-471, Journal of Materials Processing Technology, Netherlands. ISSN 0924-0136 Go to original source...
  5. KAI, Y., YING-CHUN, L., KANG-NING, Z., QING-SHUN, B., WAN-QUN, C. (2011) Tool edge radius effect on cutting temperature in micro-end-milling process, Vol. 52, pp. 905-912, International Journal of Advanced Manufacturing Technology, United Kingdom. ISSN 0268-3768 Go to original source...
  6. KUNDRÁK, J., PÁLMAI, Z., KARPUSCHEWSKI, B., FELHÕ, C.,MAKKAI, T.,BORYSENKO D. (2021) Force and temperature conditions of face milling with varying chip quotient as a function of angle of rotation, Vol. 21, pp. 214-222, Manufacturing Technology, Czech Republic. ISSN 1213-2489 Go to original source...
  7. CUI, C., DINGHU, A. Z., WU, B., LUO, M. (2017) An investigation of tool temperature in end milling considering the flank wear effect, Vol. 131-132, pp. 613-624, International Journal of Mechanical Sciences, United Kingdom. ISSN 0020-7403 Go to original source...
  8. KHANNA, N., GARAY, A., IRIARTE, L, M., SOLER, D., SANGWAN, K. S., ARRAZOLA P. J. (2012) Effect of heat Treatment Conditions on the Machinability of Ti64 and Ti54 M Alloys, Vol. 1, pp. 477-482, Procedia CIRP Go to original source...
  9. Nies³ony P.; Habart W.; Laskowski P. (2015) Metodyka wyznaczania temperatury w strefie skrawania podczas toczenia i frezowania stopu Ti6Al4V, Mechanik, Volume 8-9, pp. 413-414, Netherlands. ISSN 2212-8271
  10. GAITONDE, V. N., KARNIK, S. R., MACIEL, C. H. A., RUBIO, J. C (2016) Machinability Evaluation in Hard Milling of AISI D2 Steel, Vol. 19, pp. 360-369, Materials Research, USA. ISSN 1980-5373 Go to original source...
  11. CONRADIE, P.J.T., OOSTHUIZEN, G. A., TREURNICHT, N.F, SHAALANE, A. (2012) Overview of workpiece temperature measurement techniques for machining of Ti6Al4V, Vol. 23, pp. 116-130, South African Journal of Industrial Engineering, South Africa. ISSN 1012-277X Go to original source...
  12. LIU, D., ZHANG, Y., LUO, M., ZHANG, D. (2019) Investigation of tool wear and chip morphology in dry trochoidal milling of titanium alloy Ti-6Al-4V, Vol. 12, 1937, Materials, Switzerland. ISSN 1996-1944 Go to original source...
  13. ZAGÓRSKI I.; KULISZ M.; K£ONICA M.; MATUSZAK J. (2019) Trochoidal milling and neural networks simulation of magnesium alloys, Vol. 12, 2070, Materials, Switzerland. ISSN 1996-1944 Go to original source...
  14. NEDIC, B., ERIC, M. (2014) Cutting temperature measurement and material machinability, Vol. 18, pp. 259-268, Thermal Science, Serbia. ISSN 0354-9836 Go to original source...
  15. TAKACS, L., MCHENRY, J. S. (2006) Temperature of the milling balls in shaker and planetary mills, Vol. 41, pp. 5246-5249, Journal of Materials Science, Switzerland. ISSN 0022-2461 Go to original source...
  16. GARCÍA-HERNÁNDEZ, C., GARDE-BARACE, J-J., VALDIVIA-SÁNCHEZ, J-J., UBIETO-ARTUR, P., BUENO-PÉREZ, J-A., CANO-ÁLVAREZ, B., ALCÁZAR-SÁNCHEZ, M-Á., VALDIVIA-CALVO, F., PONZ-CUENCA, R., HUERTAS-TALÓN, J-L., KYRATSIS, P. (2021) Tro-choidal milling path with variable feed. Application to the machining of a Ti-6Al-4V part, Vol. 9, 2701, Mathematics, Switzerland. ISSN 2227-7390 Go to original source...
  17. YASHIRO, T., OGAWA, T., SASAHARA, H. (2013) Temperature measurement of cutting tool and machined surface layer in milling of CFRP, Vol. 70, pp. 63-69, International Journal of Machine Tools & Manufacture, United Kingdom. ISSN 0890-6955 Go to original source...
  18. GROCHALSKI, K., JAB£OÑSKI, P., TALAR, R., TWARDOWSKI, P., WIECZOROWSKI, M., JAKUBEK, B., RUKAT W. (2020) Temperature measurement of modern cutting tools during turning, Vol. 14, pp.37-48, Advances in Science and Technology Research Journal, Poland. ISSN 2080-4075 Go to original source...
  19. KORZYÑSKI, M. (2006) Metodyka eksperymentu, WNT Warszawa, Poland. ISBN 83-204-3203-0
  20. WASZCZUK, K. (2020) Influence of the method trochoidal tool path generation on milling process efficiency, Vol. 14 pp. 199-203, Advances in Science and Technology Research Journal, Poland. ISSN 2080-4075 Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.