Manufacturing Technology 2024, 24(1):131-140 | DOI: 10.21062/mft.2024.003

Observation of the Amount of Wear and the Microstructure of Hardfacing Layers after the Test of Resistance to Abrasive Wear

Miroslava «avodová ORCID...1, Miroslav Dľupon ORCID...2, Monika Vargová ORCID...1, Dana Stančeková ORCID...3, Jozef Krilek ORCID...1
1 Faculty of Technology, Technical University in Zvolen, ©tudentská 26, 960 53. Slovak Republic
2 Institute of Materials Research, Watsonova 47, 040 01 Koąice, Slovak Republic
3 Faculty of Mechanical Engineering, University of ®ilina, Univerzitná 1, 010 26, ®ilina. Slovak Republic

The article deals with the evaluation of the amount of wear of the base material and selected hardfac-ing materials intended for tools for wood processing in forestry after a test of resistance to abrasive wear in laboratory conditions. The values of average weight loss Wh[g] and relative resistance to abrasive wear Ψh[-] were determined by calculation. The topography of the surface after the track of the rubber disc and the abrasive of the testing device was evaluated with a confocal microscope. The depth of the disc track Pt[μm;mm] was also evaluated with a confocal microscope. The state of the samples surface after the test, as well as the overall structure and mixing of the hardwearing material with the base material was evaluated by light microscopy. A touch roughness meter was used to de-termine the profile of the track surface after the test. Based on the results, we can recommend certain hardfacing materials for practice. Their abrasive resistance and thus also the loss of material during the work load could ensure a longer service life of the tool.

Keywords: Wear, Microstructure, Confocal microscopy, Hardfacing, Abrasion
Grants and funding:

This article was created during the processing of the project VEGA 1/0609/20" Research of the cutting tools at the dendromass processing in agricultural and forestry production" and supported by the Slovak Research and Development Agency under contract No. APVV-16-0194

Received: August 4, 2023; Revised: November 14, 2023; Accepted: January 2, 2024; Prepublished online: January 8, 2024; Published: February 23, 2024  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
«avodová M, Dľupon M, Vargová M, Stančeková D, Krilek J. Observation of the Amount of Wear and the Microstructure of Hardfacing Layers after the Test of Resistance to Abrasive Wear. Manufacturing Technology. 2024;24(1):131-140. doi: 10.21062/mft.2024.003.
Share...
Download citation
  • BibTeX (.bib)
  • Bookends (.ris)
  • EasyBib (.ris)
  • EndNote (.enw)
  • EndNote 8 (.xml)
  • ISI WoS (.isi)
  • Medlars (.medlars)
  • Mendeley (.ris)
  • MODS (.xml)
  • Papers (.ris)
  • RefWorks (.txt)
  • RefManager (.ris)
  • RIS (.ris)
  • MS Word (.xml)
  • Zotero (.ris)
    • Open full article

    References

    1. «AVODOVÁ, M., HNILICA, R. (2020) Assessment of selected properties of treated tool surfaces examined to increase tool life time. In. Manufacturing Technology. 2020;20(2):257-264. doi: 10.21062/mft.2020.023. Go to original source...
    2. KALINCOVÁ, D., «AVODOVÁ, M., ĄUPTÁČIKOVÁ, V. (2018) Application of the Weld Deposits on Function Surfaces of the Forest Machines Components. In. Manufacturing Technology. 2018;18(3):400-405. doi: 10.21062/ujep/112.2018/a/1213-2489/MT/18/3/400. Go to original source...
    3. BAYHAN, Y. (2006). Reduction of wear via hardfacing of chisel ploughshare. In. Tribology International, 39, 570-574. https://doi.org/10.1016/j.triboint.2005.06.005 Go to original source...
    4. FALAT, L., D®UPON, M., «AVODOVÁ, M., HNILICA, R., ĄUPTÁČIKOVÁ, V., ČIRIPOVÁ, L., HOMOLOVÁ, V., ĎURI©INOVÁ, K. (2019) Microstructure and Abrasive Wear Resistance of Various Al-loy Hardfacings for Application on Heavy-Duty Chipper Tools in Forestry Shredding and Mulching Operations. In. Materials 2019, 12, 2212. https://doi.org/10.3390/ma12132212 Go to original source...
    5. HNILICA, R., KOTUS, M., JANKOVSKÝ, M., HNILICOVÁ, M., DADO, M. (2017) Qualitative classification of mulchers. In Agronomy Research. Vol. 15, no. 5, 2017. s.1890-1896. ISSN 1406-894X. http://dx.doi.org/10.15159/ar.17.049 Go to original source...
    6. KOLEKTÍV AUTOROV (2003) Materiály a ich správanie sa pri zváraní. VÚZ - Priemyselný inątitút, Bra-tislava (2003) 355 s. ISBN 80-88734-10-X.
    7. SCHINDLEROVÁ, V., ©AJDLEROVÁ, I. (2017) Influence tool wear in material flow. In. Advances in Science and Technology Research Journal. 2017;11(1):161-165. doi: https://doi.org/10.12913/22998624/66507 Go to original source...
    8. VIŇÁ©, J., BREZINOVÁ, J., GUZANOVÁ, A., KOTUS, M. (2013) Application of hard surfacing for re-pairing of agricultural parts. In Research in agricultural engineering. ISSN 1212-9151, 2013, vol. 59, no. 2, s. 61-67. DOI: 10.17221/4/2012-RAE Go to original source...
    9. ESAB Slovakia s.r.o. (2013) Opravy a údrľba, Príručka zvárania. 2. aktualizované vydanie.
    10. CORREA, E. O., ALCÂNTARA, N. G., VALERIANO, L. C., BARBEDO, N. D., & CHAVES, R. R. (2015) The effect of microstructure on abrasive wear of a Fe-Cr-C-Nb hardfacing alloy deposited by the open arc welding process. In Surface and Coatings Technology, 276, 479-484. https://doi.org/10.1016/j.surfcoat.2015.06.026 Go to original source...
    11. BUCHELY, M.F., GUTIERREZ, J.C., LEÓN, L.M., TORO, A. (2005). The effect of microstructure on abrasive wear of hardfacing alloys. In. Wear, Volume 259, Issues 1-6, pp. 52-61. https://doi.org/10.1016/j.wear.2005.03.002 Go to original source...
    12. JANKURA, D. (2013) Vplyv počtu vrstiev na tribologické vlastnosti tvrdonávarov. In Transfer inovácií 26/2013 https://www.sjf.tuke.sk/transferinovacii/pages/archiv/transfer/26-2013/pdf/125-129.pdf
    13. BREZINOVÁ, J., DRAGANOVSKÁ, D., GUZANOVÁ, A., BALOG, P., VIŇÁ©, J. (2016) Influence of the Hardfacing Welds Structure on Their Wear Resistance. In Metals 2016, 6, 36. https://doi.org/10.3390/met6020036. Go to original source...
    14. PRADEEP, G.R.C., ANANTHAKESAVACHAR, R., & PRASAD, B. (2010). A review paper on hardfac-ing processes and materials. In International Journal of Engineering Science and Technology. Vol. 2(11), 2010, 6507-6510.
    15. HRBACKOVA, L., SEDLAK, J., CHROMJAKOVA, F., MACUROVA, L., JURICKOVA, E., DOBROCKY, D., SKERIK, F. (2022) Evaluation of the Effect of Machining Technologies on the Surface Texture Analysis of Ertacetal C Polymer. In. Manufacturing Technology. 2022;22(6):679-692. doi: 10.21062/mft.2022.083. Go to original source...
    16. KLAUER, K., EIFLER, M., SEEWIG, J., KIRSCH, B., AURICH, J.C. (2018) Application of function-oriented roughness parameters using confocal microscopy. In Engineering Science and Technology, an International Journal, Volume 21, Issue 3, 2018, Pages 302-313, ISSN 2215-0986, https://doi.org/10.1016/j.jestch.2018.04.004. Go to original source...
    17. MÍNGUEZ-MARTÍNEZ, A., MARESCA, P., CAJA, J., OLIVA, J.D.V.Y. (2022) Results of a Surface Roughness Comparison between Stylus Instruments and Confocal Microscopes. In Materials 2022, 15, 5495. https://doi.org/10.3390/ma15165495 Go to original source...
    18. FEIDENHANS, N.A., HANSEN, P.E., PILNÝ, L., MADSEN, M. H., BISSACCO, G., PETERSEN, J. C., TABORYSKI R. (2015) Comparison of optical methods for surface roughness characterization. In. Measurement Science and Technology, Volume 26, Number 8, DOI 10.1088/0957-0233/26/8/08520 Go to original source...
    19. «AVODOVÁ, M., D®UPON, M., KALINCOVÁ, D., HNILICOVÁ, M. (2018) Deformation of Exposed Tool Parts for Crushing of Undesirable Advance Growth. In Acta Technologica Agriculturae vol.21, no.4, 3918, pp.166-173. https://doi.org/10.2478/ata-2018-0030 Go to original source...
    20. GOST 23.208-79 Ensuring of wear resistance of products. Wear resistance testing of materials by friction against loosely fixed abrasive particles. https://www.internet-law.ru/gosts/gost/4066
    21. VARGOVÁ, M., BOŁOZ, Ł., «AVODOVÁ, M., HNILICA, R. (2023) Increasing the Durability of Tools for Forest Road Maintenance. In AgriEngineering. 2023; 5(1):566-580. https://doi.org/10.3390/agriengineering5010036 Go to original source...
    22. CHANG, CH.M., CHEN, Y.CH., WU, W. (2010). Microstructural and abrasive characteristics of high carbon Fe-Cr-C hardfacing alloy. In Tribology International, Volume 43, Issues 5-6, pp. 929-934. https://doi.org/10.1016/j.triboint.2009.12.045 Go to original source...
    23. WANG, X., HAN, F., LIU X., QU, S., ZOU, Z. (2008). Microstructure and wear properties of the Fe-Ti-VMo-C hardfacing alloy. In. Wear, Volume 265, Issues 5-6, pp. 583-589. https://doi.org/10.1016/j.wear.2007.12.001 Go to original source...
    24. PADHIAR, S. A, VINCENT, S. (2020) Effect of hard facing processes on Mild steel A-36 by arc welding. In Materials Today: Proceedings, Volume 28, Part 2, 2020, Pages 526-531, ISSN 2214-7853, https://doi.org/10.1016/j.matpr.2019.12.213. Go to original source...
    25. BUČKO, M., SCHINDLEROVÁ, V., KREJČÍ, L., HLAVATÝ, P., HLAVATÝ, J. (2019) Application of welds on the high-carbon steel rails. In METAL 2019: conference proceedings: peer reviewed: 28th International Conference on Metallurgy and Materials: May 22nd-24th 2019, Hotel Voronez I, Brno, Czech Republic, EU. Ostrava: Tanger, 2019, s.1003-1009. https://doi.org/10.37904/metal.2019.886 Go to original source...
    26. MÜLLER, M., HRABĚ, P. (2013) Overlay materials used for increasing lifetime of machine parts working under conditions of intensive abrasion. In Res. Agric. Eng. 2013, 59, 16-22. DOI: 10.17221/64/2011-RAE Go to original source...

    This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.


    Return to the content