Manufacturing Technology 2024, 24(1):117-130 | DOI: 10.21062/mft.2024.014
The Influence of the Choice of Machining Strategy on Production Technology
- Tomas Bata University in Zlín, Faculty of Technology, Vavrečkova 5669,760 01 Zlín
This paper deals with the issue of selecting different machining parameters in the CAM system Siemens NX 1946. The issue of choosing between a solid end mill, milling cutter, and a high-feed tool when machining simple rectangular and rugged cavities concerning time and residual material is solved here. The chosen material was 1.1730, which is a basic material for the production of moulds without heat treatment. The paper deals with the issue of choosing the size of tool feed into the cut and its influence on the formation of the machining path depending on the depth of the cavity. The size of the residual material depends on the machining strategy and the choice of the plunge method into the material with regard to the total machining time. Performed simulations and experiments have shown a significant impact in individual settings and, thus, on the cost of machining components of such shapes.
Keywords: CAM system, Strategies, Cutting time, High-Speed Cutting
Grants and funding:
This work was supported by the Internal Grant Agency of TBU in Zlin: no. IGA/FT/2023/005
Received: September 26, 2023; Revised: January 12, 2024; Accepted: January 15, 2024; Prepublished online: January 16, 2024; Published: February 23, 2024 Show citation
References
- EREZ, H., E. DIEZ, J. PEREZ a A. VIZAN. Analysis of Machining Strategies for Peripheral Milling. Procedia Engineering [online]. 2013, 63, 573-581 [Accessed. 2023-07-21]. ISSN 1877-7058. Available at: doi:10.1016/J.PROENG.2013.08.193
Go to original source...
- IZOL, Peter, Miroslav TOMAS a Jozef BENO. Milling strategies evaluation when simulating the forming dies' functional surfaces production. Open Engineering [online]. 2016, 6(1), 98-105 [Accessed: 2023-07-21]. ISSN 23915439. Available at: doi:10.1515/ENG-2016-0013/MACHINEREADABLECITATION/RIS
Go to original source...
- VAKONDIOS, Dimitrios, Panagiotis KYRATSIS, Suleyman YALDIZ a Aristomenis ANTONIADIS. Influence of milling strategy on the surface roughness in ball end milling of the aluminum alloy Al7075-T6. Measurement [online]. 2012, 45(6), 1480-1488 [Accessed: 2023-07-21]. ISSN 0263-2241. Available at: doi:10.1016/J.MEASUREMENT.2012.03.001
Go to original source...
- SADÍLEK, Marek, Lukáš KOUSAL, Nataša NÁPRSTKOVÁ, Tomáš SZOTKOWSKI and Jiří HAJNYŠ. The Analysis of Accuracy of Machined Surfaces and Surfaces Roughness after 3axis and 5axis Milling. 2018, 18(6).
Go to original source...
- JÓZWIK a JERZY. Analysis of the Effect of Trochoidal Milling on the Surface Roughness of Aluminium Alloys after Milling. http://journalmt.com/doi/10.21062/ujep/370.2019/a/1213-2489/MT/19/5/772.html [online]. 2019, 19(5), 772-779 [Accessed: 2024-01-04]. ISSN 12132489. Available at: doi:10.21062/UJEP/370.2019/A/1213-2489/MT/19/5/772
Go to original source...
- SLABEJOVA, Silvia, Jozef HOLUBJAK, Tatiana CZÁNOVÁ, Pavol TIMKO, Andrej HORÁK a Denis PROKEIN. Surface Quality of a Groove after Trochoidal Milling with a Monolithic Ceramic Milling Cutter. http://journalmt.com/doi/10.21062/mft.2022.031.html [online]. 2022, 22(3), 334-341 [Accessed: 2024-01-04]. ISSN 12132489. Available at:10.21062/MFT.2022.031
Go to original source...
- MATRAS, A. a R. KOWALCZYK. Analysis of machining accuracy during free form surface milling simulation for different milling strategies. https://doi.org/10.1117/12.2075081 [online]. 2014, 9290, 337-343 [Accessed: 2023-07-21]. ISSN 1996756X. Available at: doi:10.1117/12.2075081
Go to original source...
- VARGA, Ján, Emil SPIŠÁK, Ivan GAJDOŠ a Peter MULIDRÁN. Comparison of Milling Strategies in the Production of Shaped Surfaces. Advances in Science and Technology. Research Journal [online]. 2022, 16(6), 267-274 [Accessed: 2023-07-21]. ISSN 2080-4075. Available at: doi:10.12913/22998624/156817
Go to original source...
- VARGA, Jan, Jozef STAHOVEC, Jozef BENO a Marek VRABEĽ. ASSESSMENT OF SURFACE QUALITY FOR CHOSEN MILLING STRATEGIES WHEN PRODUCING RELIEF SURFACES. Advances in Science and Technology. Research Journal [online]. 2014, 8(22), 37-41 [Accessed: 2023-07-24]. ISSN 2080-4075. Available at: doi:10.12913/22998624.1105163
Go to original source...
- GREŠOVÁ, Zuzana, Peter IŽOL, Marek VRABEL', L'uboš KAŠČÁK, Jozef BRINDZA a Michal DEMKO. Influence of Ball-End Milling Strategy on the Accuracy and Roughness of Free Form Surfaces. Applied Sciences 2022, Vol. 12, Page 4421 [online]. 2022, 12(9), 4421 [Accessed: 2023-07-24]. ISSN 2076-3417. Available at: doi:10.3390/APP12094421
Go to original source...
- DOBRZYNSKI, Michal, Daniel CHUCHALA, Kazimierz A. ORLOWSKI a Mateusz KACZMARCZYK. Experimental research of the effect of face milling strategy on the flatness deviations. https://doi.org/10.1080/10426914.2020.1819548 [online]. 2020, 36(2), 235-244 [Accessed: 2023-07-24]. ISSN 15322475. Available at: doi:10.1080/10426914.2020.1819548
Go to original source...
- CHOY, H. S. a K. W. CHAN. Enhanced strategy for milling corners. http://dx.doi.org/10.1243/095440502760272412 [online]. 2002, 216(8), 1135-1154 [Accessed: 2023-07-24]. ISSN 09544054. Available at: doi:10.1243/095440502760272412
Go to original source...
- MA, Feng, Hua ZHANG, Huajun CAO a K. K.B. HON. An energy consumption optimization strategy for CNC milling. International Journal of Advanced Manufacturing Technology [online]. 2017, 90(5-8), 1715-1726 [Accessed: 2023-07-24]. ISSN 14333015. Available at: doi:10.1007/S00170-016-9497-0/METRICS
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.