Manufacturing Technology 2024, 24(3):410-419 | DOI: 10.21062/mft.2024.047
Dynamic Analysis of the Propulsion Process of Tunnel Boring Machines
- School of Mechanical Engineering, Jiangsu University of Technology, Changzhou213000, China
In response to the need for trajectory correction during the excavation of curved tunnels by tunnel boring machines(TBM), as well as the impact of interference forces generated by the propulsion sys-tem on the design and service life of key components, as well as the low propulsion efficiency of TBM, a dynamic model of the propulsion mechanism during the excavation process is established, and the variation law of the angle between the key components of the thrust hydraulic cylinder and the gripper shoe hydraulic cylinder under the propulsion force of the hydraulic cylinder (1500KN) and three steer-ing angles of 0.5 °, 1 °, and 2 °, as well as the relationship between the gripper shoe hydraulic cyl-inder tightening force and horizontal propulsion force, has been studied. Research has shown that under the rated hydraulic cylinder propulsion force, during the process of increasing the swing angle of the main beam, the left angle and the tightening force on the left gripper shoe are less than the straight-line working condition, while the right side is greater than the straight-line working condition. However, during the forward excavation process after turning left, the X-direction propulsion force provided by the left thrust cylinder is greater than the X-direction propulsion force of the horizontal excavation, and the force on the left support shoe is less than the tightening force under the horizontal working condition, while the opposite is true for the right side. The research results have important theoretical significance for studying the optimal matching relationship between the mechanical model and excavation parameters of TBM during the propulsion process, as well as further improving the excavation efficiency and stability of TBM.
Keywords: TBM, Propulsion process, Thrust mechanism, Propulsion simulation
Grants and funding:
This work was supported by the Natural Science Foundation of Hunan Province of China (2021JJ30378), the Research Foundation of Education Bureau of Hunan Province of China (23A0620)
Received: January 7, 2024; Revised: May 7, 2024; Accepted: May 13, 2024; Prepublished online: May 15, 2024; Published: July 1, 2024 Show citation
References
- DU YANLIANG, DU LIJIE. Full face hard rock tunnel boring machine: system principles and integrat-ed design[M]. Wuhan: Huazhong University of Science and Technology Press, 2010.
- YAO XIAOMING. Research on TBM construction method in super long tunnel [D]. Southwest Jiao tong University, 2011.
- ZHANG HAOHUANG, LI ZHEN, GAO QINGFENG Application and Development of Full-Face Rock Tunnelling Machine in Domestic Tunnel Engineering[J]. Mining Machinery, 2018, 46(7):1-6.
- TBM virtual prototype modelling and simulation performance simulation [D]. Zhejiang University, 2016.
- LIU Z B, XIE H B, YANG H Y. Simulation analysis of pressure regulation of hydraulic thrust system on a shield tunnelling machine [C]// International Conference on Intelligent Robotics and Applications. Singapore: Springer, 2009: 493-503.
Go to original source...
- WANG F, CHEN L Z, WANG K, et al. Rapid finite element modelling method of TBM gripping-thrusting-regripping Mechanism [C]. Proceedings of the 2018 IEEE/ASME International Conference on Advanced Intelligent Mechatronics, New York: IEEE, 2018: 340-345.
Go to original source...
- Huang T, Cao R, Wu X. Design of a Biped Climbing Robot: Simulation, Comparison and Implementation. Manufacturing Technology. 2023;23(6):976-988.
Go to original source...
- HUANG T, WANG X L, LIU H T, et al. Force analysis of an open TBM gripping-thrusting regripping mechanism [J]. Mechanism and Machine Theory, 2016, 98: 101-113.
Go to original source...
- WANG K, YANG Y, HUANG T, et al. Topological structure and kinematic characteristic analysis of TBM gripping-thrusting-regripping mechanism [J]. Journal of Zhejiang University (Engineering Science), 2015, 49(10):1870-1877.
- GAO X X, YANG Y H. Finite element modelling of the gripping-thrusting-regripping mechanism of TBM based on SAMCEF [C]. Proceedings of 8th International Conference on Intelligent Robotics & Applications, Cham: Springer, 2015: 481-488.
Go to original source...
- EBRAHIM FARROKH, JAMAL ROSTAMI, Chris Laughton. Study of various models for HRIS ESTIMATION of the penetration rate of hard rock TBMs. Tunnelling and Underground Space Technology, 2012, 30: 110~123.
Go to original source...
- KAIZHI ZHANG, HAIDONG YU, ZHONG PO LIU, et al. Dynamic characteristic analysis of TBM tunnelling in mixed-face conditions. Simulation Modelling Practice and Theory, 2012, 18: 1019~1031.
Go to original source...
- YU XULIN, GUO XIAOPENG, WANG XIAOLIANG. Simulation Analysis of the Main Propeller of the New TBM Propulsion Mechanism Test Bench[J]. Mechanical Engineering & Automation, 2016(6):78-79.
- ZHANG L M, WU X G, SKIBNIEWSKI M J. Simulation-based analysis of tunnel boring machine performance in tunnelling excavation [J]. Journal of Computing in Civil Engineering, 2015, 30(4):04015073.
Go to original source...
- Cedzo M, Joch R, Timko P, Holubják J, Czánová T, ©ajgalík M. Topology Optimization of Gripping Jaws of Industrial Robot. Manufacturing Technology. 2023;23(1):25-31.
Go to original source...
- ZHANG ZHEN GONG GUOFANG, WU WEIQIANG, et al. Attitude Adaptive Control of Propulsion System of Hard Rock Tunnel Boring Machine[J]. Journal of Zhejiang University (Engineering Science), 2015, 49(10):1870-1877.
- LI WEI. Study on the uniformity of stress distribution on the contact surface between TBM gripper and surrounding rock [D].
- YU WEI. Analysis of contact between main beam TBM support and surrounding rock [D]. East China Jiao Tong University, 2015.
- RAO YUNYI, GONG HOUFANG, et al. Study on the Force of Surrounding Rock of Supporting TBM in Different Digging Conditions[J]. Construction Machinery, 2015, 46(2):21-27.
- Mo H H, Chen J S. Study on inner force and dislocation of segments caused by shield machine atti-tude[J]. Tunnelling and underground space technology, 2008, 23(3): 281-291.
Go to original source...
- SRAMOON A, SUGIMOTO M, KAYUKAWA K. Theoretical model of shield behaviour during excavation. II: Application[J]. Journal of Geotechnical and Environmental Engineering, 2002, 128(2): 156-165.
Go to original source...
- CHEN YUXI, GONG GUO FANG SHI ZHUO, etc. Coordinated control of gripper and thrust system for TBM based on construction data[J]. Journal of Zhejiang University (Engineering Science),2019,52(2):250-257.
- SHI HU, YANG HUAYONG, LONG GUOFANG, et al. Present Situation and Prospect of Key Technology and Simulated Test-bed of Shield Tunneling Machine [J]. Journal of Zhejiang Universi-ty(Engineering Edition),2013,47(05):741-749.
- WANG L, YANG X, GONG G, et al. Pose and trajectory control of shield tunnelling machine in com-plicated stratum [J]. Automation in Construction, 2018, 93: 192-199.
Go to original source...
- WU H, HUO J, MENG Z, et al. Load characteristics study with a multi-coupling dynamic model for TBM supporting system based on a field strain test [J]. Tunnelling and Underground Space Technology, 2019, 91(SEP.): 103016.
Go to original source...
- ERIKA P, FEDERICALUCIA S, JIAN Z. Analysis and estimation of gripper TBM performances in highly fractured and faulted rocks [J]. Tunnelling and Underground Space Technology, 2016, 52:44-6.
Go to original source...
- Du Y, Lu Z, Chang E, Li Q, Shi Y. Identification Method of Vibration Drilling Bit Wear State Based on Signal Imaging and Deep Learning. Manufacturing Technology. 2023;23(4):392-398.
Go to original source...
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.