Manufacturing Technology 2024, 24(6):969-976 | DOI: 10.21062/mft.2024.098
The Influence of the Crane Track Unevenness on the Load of the Supporting Crane Structure
- Faculty of Industrial Technologies in Púchov, Alexander Dubček University of Trenčín, I. Krasku 491/30, 020 01 Púchov, Slovakia
The paper presents the analysis of the gantry crane loading when driving along the crane track, using a 3D model, for which the analysis of the gantry crane frame loading was performed. The gantry crane is designed to remove dirt that is in front of the turbine under the water surface. For the gantry crane which moves along a track, the directional and vertical unevennesses were determined by experiment and are given in graphic and numerical form in (mm), relating to A track and B track with a total track length of 450 (m). Based on the knowledge of the unevenness of the rail track, the four random functional dependencies defining the irregularities of the individual rails as input variables were used for the kinematic excitation of the individual wheels of the gantry crane. The stress analysis was performed for a travel speed of 30 (m/min) and a lift of 10 (t) under the given loading. The results of the stress analysis are presented in graphic form.
Keywords: Loading, Virtual model, Load, Stress analyse, 3D model
Grants and funding:
This work was supported by the Slovak Grant Agency – project KEGA 011TnUAD-4/2024
Received: June 24, 2024; Revised: August 22, 2024; Accepted: December 2, 2024; Prepublished online: December 16, 2024; Published: December 21, 2024 Show citation
ACS | AIP | APA | ASA | Harvard | Chicago | IEEE | ISO690 | MLA | NLM | Turabian | Vancouver |
References
- BRÁT, V., (1976), Handbook of Kinematics with Examples, Prague, SNTL
- DIŽO, J., HARUŠINEC, J., BLATNICKÝ, M. (2018). Computation of modal properties of two types of freight wagon bogie frames using the finite element method. In: Manufacturing Technology. Vol. 18, No. 2, pp. 208-214. J. E. Purkyne University in Usti n. Labem. Czech Republic
Go to original source...
- GERLICI, J., GORBUNOV, M., KRAVCHENKO, K., DOMIN, R., LACK, T. (2017) Slipping and Skidding Occurrence Probability Decreasing by Means of the Friction Controlling in the Wheel-Braking Pad and Wheel-Rail Contacts. In.: Manufacturing Technology. Vol. 17, No.2, pp. 179-186, ISSN 1213-2489
Go to original source...
- HAUSER, V., NOZHENKO, O. S., KRAVCHENKO, K. O., LOULOVÁ, M., GERLICI, J., LACK, T. (2017). Impact of Wheelset Steering and Wheel Profile Geometry to the Vehicle Behavior when Passing Curved Track. In.: Manufacturing Technology. ISSN 1213-2489 vol. 17, pp 306-312
Go to original source...
- Klimenda, F., Soukup, J., Skočilasová, B., Skočilas, J. (2020). Vertical Vibration of the Vehicle when Crossing over Transverse Speed Bumps. DOI: 10.21062/mft.2020.020 © Manufacturing Technology. Vol. 20, No. 1 ISSN 1213-2489
Go to original source...
- SAGA, M., VAVRO, J., KOPECKÝ, M., (2002), Počítačová analýza a syntéza mechanických sústav. ISBN 80-968605-4-2, Žilina, 267 s.
- Svoboda, M., Chalupa, M., Černohlávek, V., Švásta, A., Meller, A., Schmid, V. (2023). Measuring the Quality of Driving Characteristics of a Passenger Car with Passive Shock Absorbers. In.: Manufacturing Technology. Vol. 23, No. 1 ISSN 1213-2489 e-ISSN 2787-9402, DOI: 10.21062/mft.2023.023 © 2023
Go to original source...
- Tomsovsky, L., Lopot, F., Jelen, K. (2022). Kinematic Analysis of the Tram-pedestrian Collision - a Pre-liminary Case Study. In.: Manufacturing Technology. Vol. 22, No. 1 ISSN 1213-2489, DOI: 10.21062/mft.2022.007 © 2022
Go to original source...
- VAVRO, J., (2020), Kinematic and Dynamic Analysis of Planar Mechanisms by Means of the SolidWorks Software, Tribun EU s. r. o., ISBN 978-80-263-1495-0, p. 156.
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.