Manufacturing Technology 2025, 25(1):67-75 | DOI: 10.21062/mft.2025.009

Optimized for Silicon Wafer Dicing Blade Machining and Grinding Parameters of Structure

Dongya Li ORCID..., Wangchao Jiang ORCID..., Henan Qi ORCID...
Applied Technology College of Soochow University, Suzhou 215000, China

When diamond scribing knives are used to grind silicon wafers at ultra-high speeds, slight changes in the structure of the diamond scribing knives and changes in the grinding parameters will have a large impact on the processing accuracy and appearance of the silicon wafers. In order to reduce the defective rate of silicon wafers, improve the service life of diamond scribing knives and grinding efficiency. To address this issue, the working mechanism of the scribing knife grinding is analysed in the paper, the influence of spindle speed and feed rate on the quality of the silicon wafer slit when the scribing knife is grinding is studied, and the chipping of silicon wafers is observed through the scanning electron microscope and optical microscope, so as to analyse the shape of the cross-section, length of the cutting edge, concentration of diamond particles in the cutting edge, thickness of the cutting edge and determine the structure of the scribing knife, and to test its influence on the silicon wafer slit by means of the grinding experiments. The structure of the scribing knife was determined, and its influence on the quality of silicon wafer slit was tested by grinding experiment. The results show that the wear rate of diamond particles, slit quality and processing efficiency of the scribing knife are optimal when grinding silicon wafers at 50,000 r/min and 60-80 mm.sec-1. The above study can help to further understand the wear mechanism of the scribing knife in the process of ultra-high-speed grinding of silicon wafers, improve the machining efficiency, and prolong the service life of the tool.

Keywords: Scribing knife, Grinding mechanism, Tool structure optimization, Parameter optimization
Grants and funding:

Jiangsu Qinglan Project; Teaching Reform Research Project, Applied Technology College of Soochow University (JG202301)

Received: November 27, 2024; Revised: February 21, 2025; Accepted: March 1, 2025; Prepublished online: March 1, 2025; Published: April 25, 2025  Show citation

ACS AIP APA ASA Harvard Chicago IEEE ISO690 MLA NLM Turabian Vancouver
Li D, Jiang W, Qi H. Optimized for Silicon Wafer Dicing Blade Machining and Grinding Parameters of Structure. Manufacturing Technology. 2025;25(1):67-75. doi: 10.21062/mft.2025.009.
Download citation

References

  1. CHIEW, Y. H., LIONG, J. Y., & TAN, F. F. (2018). Mechanical Dicing Challenges and Development on 50um Saw Street with Wafer Backside Coating (WBC). 2018 IEEE 38th International Electronics Manufacturing Technology Conference (IEMT), Melaka, Malaysia, IEEE, pp.1-8. DOI: 10.1109/IEMT.2018.8511708 Go to original source...
  2. VENKATESH, V. C., FANG, F., & CHEE, W. K. (1997). On-mirror surfaces obtained with and without polishing. CIRP Annals, Vol. 46, No.1, pp.505-508. https://doi.org/10.1016/S0007-8506(07)60876-2 Go to original source...
  3. ZHOU, H., QIU, S., HUO, Y., & ZHANG, N. (2013). High-speed dicing of silicon wafers conducted using ultrathin blades. The International Journal of Advanced Manufacturing Technology, Vol. 66, No.5-8, pp.947-953. https://doi.org/10.1007/s00170-012-4379-6 Go to original source...
  4. LIN, J. W., & CHENG, M. H. (2014). Investigation of chipping and wear of silicon wafer dicing. Journal of Manufacturing Processes, Vol. 16, No.3, pp.373-378. https://doi.org/10.1016/j.jmapro.2014.04.002 Go to original source...
  5. ARAUJO, L. A. O., FOSCHINI, C. R., JASINEVICIUS, R. G., & FORTULAN, C. A. (2016). Precision dicing of hard materials with abrasive blade. The International Journal of Advanced Manufacturing Technology, Vol. 86, No.9-12, pp.2885-2894. https://doi.org/10.1007/s00170-016-8394-x Go to original source...
  6. SU, T. J., CHEN, Y. F., CHENG, J. C., & CHIU, C. L. (2018). Optimizing the dicing saw parameters of 60μm wafer dicing street. Microsystem Technologies, Vol. 24, No.10, pp.3965-3971. https://doi.org/10.1007/s00542-017-3553-z Go to original source...
  7. LI, K., WANG, M., CHEN, F., YAN, N., ZOU, Q., ZHAO, Y., ZHAO, F. (2019). Analysis of the Dynamic Diameter of Superthin Diamond Blades in the High Speed and Precison Dicing Process. International Journal of Precision Engineering and Manufacturing, Vol. 20, No.7, pp.1071-1081. https://doi.org/10.1007/s12541-019-00128-7 Go to original source...
  8. YUAN, Z., CHENG, K., ZHANG, Y., HU, J., & ZHENG, P. (2019). Investigation on the fabrication of dicing blades with different sintering methods for machining hard brittle material wafers. Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture, Vol. 233, No.07, pp.1781-1793. Go to original source...
  9. LEUNG, T. P., LEE, W. B., & LU, X. M. (1998). Diamond turning of silicon substrates in ductile-regime. Journal of Materials Processing Technology, Vol.73, No.1-3, pp.42-48. https://doi.org/10.1016/S0924-0136(97)00210-0 Go to original source...
  10. YAN, W.W., GAO, Q.Y. (2014). The Research of Dicing Saw's Dicing Process. Equipment for Electronic Products Manufacturing, Vol.43, No.11, pp.24-28.
  11. LANG, X.H., ZHANG W.Q., SUN, B., YAN, Q.L. (2014). Dicing Saw Machine in the Application of the GaAs Material Cutting. Equipment for Electronic Products Manufacturing, Vol.43, No.04, pp.12-14+53.
  12. WANG, M.H., ZHANG S.N., SHAO, C.F., ZHUANG, X., ZHANG, Z.Y. (2017). Effect of Technological Parameters on Cutting Force of Single Crystal Silicon in Ultra-precision Machining. Machine Tool & Hydraulics, Vol.45, No.19, pp.45-48+56.
  13. ZHANG, Y.X. (2006). Study on the Surface Layer Damage of Monocrystalline Silicon Wafer Induced by Ultra-Precision Grinding [D]. Dalian: Dalian University of Technology.
  14. DRBAL, M., KOLOMY, S., SEDLAK, J., ZOUHAR, J., VITEK, J. (2024). Investigation of the Tool Wear Progression in Parting Technology. Manufacturing Technology, Vol. 24, No. 6, pp. 901-913. Doi: 10.21062/mft.2024.093 Go to original source...
  15. TSAI, M. Y., & HOO, Z. T. (2019). Polishing single-crystal silicon carbide with porous structure diamond and graphene-TiO2 slurries. The International Journal of Advanced Manufacturing Technology, Vol. 105, No.1-4, pp.1519-1530. https://doi.org/10.1007/s00170-019-04223-x Go to original source...
  16. PRATAP, A., PATRA, K., & DYAKONOV, A. A. (2019). On-machine texturing of PCD micro-tools for dry micro-slot grinding of BK7 glass. Precision Engineering, Vol. 55, pp.491-502. https://doi.org/10.1016/j.precisioneng.2018.11.004 Go to original source...
  17. AZAR, A. S., HOLME, B., & NIELSEN, Ø. (2016). Effect of sawing induced micro-crack orientations on fracture properties of silicon wafers. Engineering Fracture Mechanics, Vol. 154, pp.262-271. https://doi.org/10.1016/j.engfracmech.2016.01.014 Go to original source...
  18. LIU, H., WEI, Y., WANG, J., & XU, S. (2016). Investigation of single cut process in mechanical dicing for thick metal wafer. 2016 17th International Conference on Electronic Packaging Technology (ICEPT), Wuhan, China, IEEE, pp. 26-30. DOI: 10.1109/ICEPT.2016.7583083 Go to original source...
  19. TIAN, W., WANG, W., WANG, Y., ZHANG, S. (2024). Study on Multi-Objective Optimization of Milling Process of Powder Metallurgy Titanium Aluminum Alloys. Manufacturing Technology, Vol. 24, No. 4, pp. 652-667. Doi: 10.21062/mft.2024.064 Go to original source...
  20. ĞAVODOVÁ, M., VARGOVÁ, M., KRILEK, J., STANÈEKOVÁ, D. (2022). Analysis of Damaged Delimber Knives and the Possibility of Increasing their Service Life. Manufacturing Technology, Vol. 22, No. 1, pp. 80-88. Doi: 10.21062/mft.2022.011 Go to original source...
  21. WU, H. (2021). Wear characteristics of single diamond grit scratching on sapphire with different contact forms. Ceramics International, Vol. 47, No.7, Part A, pp. 8840-8848. https://doi.org/10.1016/j.ceramint.2020.12.005 Go to original source...
  22. ZHANG, Q., ZHAO, Q., TO, S., GUO, B., & ZHAI, W. (2017). Diamond wheel wear mechanism and its impact on the surface generation in parallel diamond grinding of RB-SiC/Si. Diamond and Related Materials, Vol. 74, pp.16-23. https://doi.org/10.1016/j.diamond.2017.01.019 Go to original source...
  23. RAO, X., ZHANG, F., LU, Y., LUO, X., DING, F., & LI, C. (2019). Analysis of diamond wheel wear and surface integrity in laser-assisted grinding of RB-SiC ceramics. Ceramics International, Vol. 45, No.18, Part A, pp.24355-24364. https://doi.org/10.1016/j.ceramint.2019.08.154 Go to original source...
  24. MA, Z., WANG, Z., WANG, X., & YU, T. (2020). Effects of laser-assisted grinding on surface integrity of zirconia ceramic. Ceramics International, Vol. 46, No.1, pp.921-929. https://doi.org/10.1016/j.ceramint.2019.09.051 Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.