Manufacturing Technology 2026, 26(4):453-460 | DOI: 10.21062/mft.2026.037
Analysis of the Influence of Laser Welding Parameters on the Quality of the Lap Joint
- 1 Faculty of Mechanical Engineering, Czestochowa University of Technology, Dabrowskiego 69, 42-201 Czestochowa, Poland
- 2 Faculty of Architecture, Civil Construction and Applied Arts, Academy of Silesia, Rolna 43, 40-555 Katowice, Poland
- 3 Faculty of Industrial Technologies, Alexander Dubček University of Trenčín, Ivana Krasku 491/30, 020 01 Púchov, Slovak Republic
The analysis presented focuses on the relationship between laser welding parameters and the strength properties of lap joints. The objective of the research was to design a numerical model for estimating the strength properties of lap joints welded by laser beam. As part of the work, experimental tests were carried out and then numerical simulations were performed. Experimental tests were performed for a lap joint welded using two different welding depths. A joint with full and partial penetration of materials was obtained. The material used for the lap joint is two flat bars with dimensions of 100x200x2 [mm] made of X5CrNi18-10 austenitic steel. Mechanical strength measurements and macroscopic studies were performed to identify the properties of the lap joint. To identify the properties of the lap joint, mechanical strength tests and macroscopic examinations were conducted. Based on experimental studies, discrete models of the analyzed lap joints were developed in the Abaqus FEM program. Simulation calculations of the laser welding process were performed. The obtained simulation results were input data for further numerical strength analysis. To validate the numerical models, the results obtained were compared with experimental data.
Keywords: Numerical modelling, Lap joint, Laser welding, Temperature field, Stress analysis, Deformations
Received: February 12, 2026; Revised: June 16, 2026; Accepted: June 18, 2026; Prepublished online: July 13, 2026; Published: November 17, 2026 Show citation
| ACS | AIP | APA | ASA | Harvard | Chicago | Chicago Notes | IEEE | ISO690 | MLA | NLM | Turabian | Vancouver |
References
- TAYEBI, M., MOHAMMAD SOLTANI, H., RAJAEE, A. (2022). Laser Welding.
Go to original source... - DANIELEWSKI, H., SKRZYPCZYK, A.; HEBDA, M.; TOFIL, SZ., WITKOWSKI, G.; DŁUGOSZ, P.; NIGROVIC R. (2020) Numerical and metallurgical analysis of laser welded, sealed lap joints of S355J2 and 316L steels under different configurations. Materials, Vol. 13, 5819. MDPI. ISSN: 1996-1944
Go to original source... - HAOYAN, W., QIZHI, H., JIUN-SHYAN, CH., HUI-PING, W., BLAIR, E. C. (2017) Coupled thermal-mechanical-contact analysis of hot cracking in laser welded lap joints. Journal Laser Applications., Vol. 29 No 2: 022412. AIP Publishing Journals. ISSN: 1938-1387
Go to original source... - XIAOHUA, W. & MINGLIANG, Z. (2025) Effect of Brass Solder Composition on Quality in Laser Welding of Solar Panel Busbar. Manufacturing Technology Journal, 25, 424-30. ISSN: 1213-2489
Go to original source... - NILSSON, P., ATASHIPOUR, S. R., AL-EMRANI, M. (2023). Laser-Welded Corrugated-Core Sandwich Composition-Numerical Modelling Strategy for Structural Analysis. Journal of Composites Science, 7(9), 349. ISSN: 2504-477X
Go to original source... - CHEN, G., HIROHATA, M., HYOMA, K. et al. (2024) Deformation and residual stress of T-shaped joints fabricated by laser-arc hybrid welding for steel bridge members. Weld World 68, 459-473. ISSN: 0043-2288
Go to original source... - DE, A., MAITI, S.K., WALSH, C.A., BHADESIA, K.D.H., (2003), Finite element simulation of laser spot welding. Science Technology of Welding and Joining, Vol. 8, No. 5, pp. 377-384. IM3. ISSN: 1362-1718
Go to original source... - DOMAŃSKI, T., PIEKARSKA, W., SATERNUS, Z., KUBIAK, M., STANO, S. (2022). Numerical Prediction of Strength of Socket Welded Pipes Taking into Account Computer Simulated Welding Stresses and Deformations. Materials, Vol. 15, No 9, 3243. ISSN: 1996-1944
Go to original source... - PIEKARSKA, W. (2007) Numerical analysis of thermomechanical phenomena during laser welding process. The temperature fields, phase transformation and stresses. Wydawnictwo Politechniki Częstochowskiej. Częstochowa. Poland
- CASALINO, G., DAL Maso, U., ANGELASTRO, A., CAMPANELLI, S.L. Hybrid Laser Welding: A Review. In DAAAM International Scientific Book; DAAAM International Vienna: Maria Lankowitz, Austria, 2010; Chapter 38; pp. 413-430. ISBN: 978-3-901509-74-7.
- KUBIAK, M., SATERNUS, Z., DOMAŃSKI, T., URBAŃCZYK, M., TALA¦KA, K., WILCZYŃSKI, D., WOJTKOWIAK, D. (2026). Modelling of Bead-on-Plate Laser Beam Melting Using Innovative Laser with a Single-Mode Core Surrounded by a Multimode Ring. Materials, 19(7), 1423. ISSN: 1996-1944.
Go to original source... - HAVRILLA, D., BROCKMANN, R. (2009). Third generation of disk lasers: a new benchmark for indus-trial solid state lasers. Laser Technik Journal, 6(3), 26-31. ISSN: 1614‑0874
Go to original source... - PARK, J. H., MOON, H. S. (2020). Advanced automatic welding system for offshore pipeline system with seam tracking function. Applied Sciences, 10(1), 324. ISSN: 2076‑3417
Go to original source... - KRISHMA MURTHY, K.R.; AKYEL, F.; REISGEN, U.; OLSCHOK, S. (2022) Simulation of transient heat transfer and phase transformation in laser beam welding for low alloy steel and studying its influences on the welding residual stresses. Journal of Advanced Joining Processes, 5, 100080. ISSN: 2666‑3309
Go to original source... - SULAIMAN, S.K., ALKAHARI, M.R., JUZAILA ABD LATIF, M., HARANGAN PRASADA MANURUNG, Y. PRIAPRATAMA PRAJADHIANA, K. (2025) Thermal Analysis of Micro Plasma Wire Arc Additive Manufacturing Deposition Process. Manufacturing Technology Journal, 25, 396-404. ISSN: 1213-2489
Go to original source... - KORIC, S., THOMAS, B. (2007). Thermo-mechanical model of solidification processes with ABAQUS. Proceedings of the Abaqus Users' Conference, Paris. France. 22-24 May
- SAPIETOVÁ, A., DEKÝ©, V., SAPIETA, M., PECHÁČ, P. (2014). Application of computational and design approaches to improve carrier stability. Procedia Engineering, 96, pp. 410-418. ISSN: 1877-7058
Go to original source... - JIMÉNEZ-XAMÁN, M., HERNÁNDEZ-HERNÁNDEZ, M., TARIQ, R., LANDA-DAMAS, S., RODRÍGUEZ-VÁZQUEZ, M., ARANDA-ARIZME, A., CRUZ-ALCANTAR, P. (2024) Numerical simulations and mathematical models in laser welding: a review based on physics and heat source models. Frontiers in Mechanical Engineering, vol. 10. ISSN: 2297‑3079
Go to original source... - ROSLI, N.A., ALKAHARI, M.R., RAMLI, F.R., FADZLI bin Abdollah, M., IKHWAN Abdul Kudus, S., GAZALI Herawan, S. (2022). Parametric Optimisation of Micro Plasma Welding for Wire Arc Additive Manufacturing by Response Surface Methodology. Manufacturing Technology Journal, 22(1), 59-70. ISSN: 1213-2489
Go to original source... - HIETALA, M., JÄRVENPÄÄ, A., KESKITALO, M., JASKARI, M., MÄNTYJÄRVI, K. (2019). Tensile and fatigue properties of laser-welded ultra-high-strength stainless spring steel lap joints. Procedia Manufacturing, Vol. 36, pp 131-137. ISSN: 2351-9789
Go to original source... - FURUSAKO, S., MIYAZAKI, Y., & AKINIWA, Y. (2015). Tensile shear strength of laser lap joints. Welding International, Vol. 29, No 11, pp. 838-846. Taylor&Francis. ISSN: 0950‑7116
Go to original source... - WANG, H., WANG, Y., LI, X., WANG, W., YANG, X. (2021). Influence of assembly gap size on the structure and properties of SUS301L stainless steel laser welded lap joint. Materials, vol. 14, 996. ISSN: 1996-1944
Go to original source... - HAN, Y., JIAXUAN, Z., LINJIE, Z. (2024), Effects of filler materials on the microstructural characteristics and mechanical properties of laser-welded lap joints of TZM alloys. International Journal of Refractory Metals and Hard Materials, vol. 122, 106696. Elsevier. ISSN: 0263-4368,
Go to original source... - BRICÍN, D., ©PIRIT, Z., GILÍK, H., KAUFMAN, J. (2024). Effect of Laser Shock Peening on the Microstructure of P265GH Steel and X6CrNiTi18-10 Stainless Steel Dissimilar Welds. Manufacturing Technology Journal, 24(1), 9-14. ISSN: 1213-2489
Go to original source... - RENZHI, Zh., DAICHI, N., NINSHU, M., FENGGUI, L., TETSUO, S., TAKAYUKI T., SYUICHI Sh. (2025) Numerical modelling of laser welding pool thermal dynamics and dissimilar materials mixing of cast iron, carbon steel and nickel-alloy wire for weld crack prevention. Journal of Manufacturing Processes, vol. 156B, 398-410. ISSN 1526-6125
Go to original source... - TARABA, M., VAVRO, J., VAVRO, J. (2025). Implementation of Mechanization into the Welding Process. Manufacturing Technology Journal, 25(1), 120-130. ISSN: 1213-2489
Go to original source... - WAŁĘSA, K., TALA¦KA, K., WILCZYŃSKI, D. (2026). Modelling of Mechanical Properties of Thermoplastic Elastomer for Simulation of Belt Welding Process. Acta Physica Polonica A, 149(2), S68. ISSN: 0587‑4246
Go to original source... - SHAFIQ, M. R. (2024). Effect of Laser Welding parameters on Tensile strength of different metals: Meta-analysis. Welding Technology Review, 96, 27-33. ISSN: 2081‑2243
Go to original source... - TSIRKAS, S.A., PAPANIKOS, P., KERMANIDIS TH. (2003), Numerical simulation of the laser welding process in butt-joint specimens. In: Journal of Materials Processing Technology, Vol. 134, pp. 59-69. ISSN: 1873-4774
Go to original source... - DASSAULT SYSTEM (2007). Abaqus Theory Manual, Version 6.7. SIMULIA. Vélizy-Villacoublay, France
This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.



ORCID...