Manufacturing Technology 2026, 26(4):497-516 | DOI: 10.21062/mft.2026.038

Enhancement of Hot Deep Drawing Die Wear Rate using Artificial Intelligence Lubricant Additive

Zaman Khalil Ibrahim ORCID...1,2, Jafar Keighobadi ORCID...1
1 Faculty of Mechanical Engineering, University of Tabriz, Tabriz, Islamic Republic of Iran
2 Kut Technical Institute, Middle Technical University, 10001 Baghdad, Iraq

Currently, lubricant additives represent an effective approach for addressing the increasing industrial demand for enhanced tribological performance and extended service life of forming tools. Graphene-based nanocomposites have shown considerable potential in reducing wear and friction while improving lubricant viscosity and thermal stability. Therefore, this study investigates the tribological performance of graphene-enhanced lubricants containing concentrations of 0, 2, 4, 6, 8, and 10 mg/ml graphene combined with 2 wt.% TiO₂ nano-additives under deep drawing conditions. Experiments were conducted within a temperature range of 25–150 °C and applied loads from 5–50 N. The results demonstrated that the lubricant containing 6 mg/ml graphene exhibited the highest tribological enhancement among all tested concentrations. This concentration achieved approximately 43% improvement in wear resistance, 40% reduction in coefficient of friction, and 35% increase in kinetic viscosity compared with the base lubricant without graphene additives. The superior performance of the 6 mg/ml formulation is attributed to the formation of a more stable protective tribofilm, enhanced load-carrying capacity, improved surface separation, and increased thermal stability under severe operating conditions. Furthermore, the addition of graphene nanoparticles significantly reduced direct metal-to-metal contact and improved lubricant film durability, particularly at elevated temperatures and higher applied loads. To further analyze and optimize the experimental results, an artificial neural network model based on a multilayer perceptron (MLP) architecture was developed using both experimental and simulation data. The artificial neural network (ANN) model demonstrated strong predictive capability for wear rate, coefficient of friction, and viscosity as functions of graphene concentration, temperature, and load. The findings confirm the effectiveness of graphene-enhanced nanolubricants in improving the durability and efficiency of deep drawing dies for industrial applications.

Keywords: Graphene, Deep drawing, Nanocomposite, Lubricant additive, Tribological properties, Friction, Wear, Artificial neural network

Received: December 1, 2025; Revised: June 23, 2026; Accepted: June 26, 2026; Prepublished online: June 30, 2026; Published: November 17, 2026  Show citation

ACS AIP APA ASA Harvard Chicago Chicago Notes IEEE ISO690 MLA NLM Turabian Vancouver
Ibrahim ZK, Keighobadi J. Enhancement of Hot Deep Drawing Die Wear Rate using Artificial Intelligence Lubricant Additive. Manufacturing Technology. 2026;26(4):497-516. doi: 10.21062/mft.2026.038.
Download citation

References

  1. JIANG, Z., ZHAO, J., XIE, H. (2017). Microforming technology: Theory, simulation and practice (1st ed.). Academic Press. ISBN 9780128112120
  2. HOUARI, A., MADANI, K., BENYETTOU, M., KADDOURI, N., BELHOUARI, M., AMROUNE, S., MOHAMAD, B., BENAMAR, B., CHELLIL, A. (2025). Estimation of the stress-intensity factor value in the presence of an adhesive defect for a damaged plate repaired with a composite patch. Metallofizika i Noveishie Tekhnologii, 47(1), 103-123.
  3. DAODON, W., SAETANG, V. (2023). Improvement of Frictional Property of AISI D2 Tool Steel Surface against JIS SPFC 980Y Advanced High-Strength Steel by Using Laser Texturing Process. Lubricants, 11(2), 68. Go to original source...
  4. KUCLOURYA, T., MUDLIAR, S., JAIN, M. K., THAMBA, N. B. (2021). A review on graphene-reinforced composites for ballistic applications. IOP Conference Series: Materials Science and Engineering, 1123(1), 012051. Go to original source...
  5. PRASHANTHA KUMAR, H. G., ANTHONY XAVIOR, M. (2014). Graphene reinforced metal matrix composite (GRMMC): A review. Procedia Engineering, 97, 1033-1040. Go to original source...
  6. BORAH, M., DAHIYA, M., SHARMA, S., MATHUR, R. B., DHAKATE, S. (2014). Few layer graphene derived from wet ball milling of expanded graphite and few layer graphene based polymer composite. Materials Focus, 3. Go to original source...
  7. WANG, X., ZHANG, Y., YIN, Z., SU, Y., ZHANG, Y., CAO, J. (2019). Experimental research on tribological properties of liquid phase exfoliated graphene as an additive in SAE 10W-30 lubricating oil. Tribology International, 135, 29-37. Go to original source...
  8. LI, L. ZHOU, M. JIN, L. LIU, L. MO, Y. LI, X. MO, Z. LIU, Z. YOU, S., ZHU, H. (2019) Research Progress of the Liquid-Phase Exfoliation and Stable Dispersion Mechanism and Method of Graphene. Front. Mater. 6:325. Go to original source...
  9. WANG, J., ZHUANG, W., YAN, T., LIANG, W., LI, T., ZHANG, L., WEI, X. (2021). Tribological performances of copper perrhenate/graphene nanocomposite as lubricating additive under various temperatures. Journal of Industrial and Engineering Chemistry, 100, 296-309. Go to original source...
  10. XIAO, H., LIU, S. (2017). 2D nanomaterials as lubricant additive: A review. Materials & Design, 135, 319-332. Go to original source...
  11. HOLMBERG, K., ANDERSSON, P., NYLUND, N.-O., MÄKELÄ, K., ERDEMIR, A. (2014). Global energy consumption due to friction in trucks and buses. Tribology International, 78, 94-114. Go to original source...
  12. RESTUCCIA, P., RIGHI, M. C. (2016). Tribochemistry of graphene on iron and its possible role in lubri-cation of steel. Carbon, 106, 118-124. Go to original source...
  13. LI, J., ZENG, X., REN, T., VAN DER HEIDE, E. (2014). The Preparation of Graphene Oxide and Its Derivatives and Their Application in Bio-Tribological Systems. Lubricants, 2(3), 137-161. Go to original source...
  14. SUN, J., DU, S. (2019). Application of graphene derivatives and their nanocomposites in tribology and lubrication: A review. RSC Advances, 9(69), 40642-40661. Go to original source...
  15. LI, Y., ZHANG, S., DING, Q., FENG, D., QIN, B., HU, L. (2018). Liquid metal as novel lubricant in a wide temperature range from -10 to 800 °C. Materials Letters, 215, 140-143. Go to original source...
  16. MOBARK, H. F. H., AL-AZZAWI, A. H., ABID ALI, A. K., MOHAMAD, B. (2024). Comparative tribological analysis of Al-Fe-Si and Al-Fe-Cr based alloys. Structural Integrity and Life, 24(3), 386-392. Go to original source...
  17. YANG, Y., JIA, W., MA, L., ZHU, J., WANG, H., HOU, K., WANG, J., YANG, S. (2022). A feasible construction strategy of GO-based hetero-film with long service life at multi-environments: Effective friction transfer application. Tribology International, 168, 107455. Go to original source...
  18. PAUL, G., SHIT, S., HIRANI, H., KUILA, T., MURMU, N. C. (2019). Tribological Behavior of Dodecyl-amine Functionalized Graphene Nanosheets Dispersed Engine Oil Nanolubricants." Tribology International, vol. 131, 2019, pp. 605-619. Go to original source...
  19. DONG, H. S., QI, S. J. Realising the Potential of Graphene-Based Materials for Biosurfaces-A Future Perspective." Biosurface and Biotribology, vol. 1, no. 4, 2015, pp. 229-248. Elsevier, Go to original source...
  20. KIM, K.-S., LEE, H.-J., LEE, C., LEE, S.-K., JANG, H., AHN, J.-H., KIM, J.-H., LEE, H.-J. (2011). Chemical vapor deposition-grown graphene: The thinnest solid lubricant. ACS Nano, 5(6), 5107-5114. Go to original source...
  21. WU, P., CHEN, X., ZHANG, C., ZHANG, J., LUO, J., ZHANG, J. (2021). Modified graphene as novel lubricating additive with high dispersion stability in oil. Friction, 9, 143-154. Go to original source...
  22. ZHANG, L., HE, Y., ZHU, L., YANG, C., NIU, Q., AN, C. (2017). In situ alkylated graphene as an oil-dispersible additive for friction and wear reduction. Industrial & Engineering Chemistry Research, 56(32), 9029-9034. Go to original source...
  23. SPEAR, J. C., EWERS, B. W., BATTEAS, J. D. (2015). 2D-nanomaterials for controlling friction and wear at interfaces. Nano Today, 10(3), 301-314. Go to original source...
  24. CHOUHAN, A., MUNGSE, H. P., KHATRI, O. P. (2020). Surface chemistry of graphene and graphene oxide: A versatile route for their dispersion and tribological applications. Advances in Colloid and Interface Science, 283, 102215. Go to original source...
  25. SARNO, M., SCARPA, D., SENATORE, A., AHMED ABDALGLIL MUSTAFA, W. (2020). rGO/GO Nanosheets in Tribology: From the State of the Art to the Future Prospective. Lubricants, 8(3), 31. Go to original source...
  26. LI, S., LI, Q., CARPICK, R. W., GUMBSCH, P., LIU, X. Z., DING, X., SUN, J., LI, J. (2016). The evolving quality of frictional contact with graphene. Nature, 539(7630), 541-545. Go to original source...
  27. VINOTH, A., NIRMAL, K.N., KHEDAR, R., DATTA, S. (2021). Optimizing the Tribological Properties of UHMWPE Nanocomposites-An Artificial Intelligence based approach. In: Akinlabi, E., Ramkumar, P., Selvaraj, M. (eds) Trends in Mechanical and Biomedical Design. Lecture Notes in Mechanical Engineering. Springer, Singapore. Go to original source...
  28. DATTA, S., CHATTOPADHYAY, P. P. (2013). Soft computing techniques in advancement of structural metals. International Materials Reviews, 58(8), 475-504. Go to original source...
  29. SINHA, A., SIKDAR (DEY), S., CHATTOPADHYAY, P. P., DATTA, S. (2013). Optimization of mechanical property and shape recovery behavior of Ti-(∼49at.%) Ni alloy using artificial neural network and genetic algorithm. Materials & Design, 46, 227-234. Go to original source...
  30. BHATTACHARYYA, T., SINGH, S. B., SIKDAR (DEY), S., BHATTACHARYYA, S., BLECK, W., BHATTACHARJEE, D. (2013). Microstructural prediction through artificial neural network (ANN) for development of transformation induced plasticity (TRIP) aided steel. Materials Science and Engineering: A, 565, 148-157. Go to original source...
  31. MOHANTY, I., BHATTACHARJEE, D., DATTA, S. (2011). Designing cold rolled IF steel sheets with optimized tensile properties using ANN and GA. Computational Materials Science, 50(8), 2331-2337. Go to original source...
  32. HETTIARACHCHI, S. J., BOWEN, J., KERSHAW, M., BARAGAU, I.-A., NICOLAEV, A., KELLICI, S. (2023). Nanostructured Al₂O₃/graphene additive in bio-based lubricant: A novel approach to improve engine performance. Tribology International, 186, 108619. Go to original source...
  33. MIAO, X., LIU, S., MA, L., YANG, Y., ZHU, J., LI, Z., WANG, J. (2022). Ti3C2-graphene oxide nanocomposite films for lubrication and wear resistance. Tribology International, 167, 107361. Go to original source...
  34. MADKOUR, T. M., FADL, S., DARDIR, M. M., MEKEWI, M. A. (2016). High performance nature of biodegradable polymeric nanocomposites for oil-well drilling fluids. Egyptian Journal of Petroleum, 25(2), 281-291. Go to original source...
  35. OMRANI, E., MOGHADAM, A. D., KASAR, A. K., ROHATGI, P., MENEZES, P. L. (2021). Tribological Performance of Graphite Nanoplatelets Reinforced Al and Al/Al2O3 Self-Lubricating Composites. Materials, 14(5), 1183. Go to original source...
  36. Zhou, H., Shi, X., Liu, X., Lu, G., Chen, Y. (2019). Tribological properties and self-repairing functionality of Ti6Al4V-multilayer graphene-Ag composites. Journal of Materials Engineering and Performance, 28(6), 3381-3392. Go to original source...
  37. WANG, W., HAN, Z., WANG, Q., WEI, B., XIN, S., GAO, Y. (2020). Tribological Properties of Ti2AlNb Matrix Composites Containing Few-Layer Graphene Fabricated by Spark Plasma Sintering. Metals, 10(7), 924. Go to original source...
  38. BAO, J., CHEN, G., ZHAO, J., HE, Y., HUANG, Y., LUO, J. (2021). Improvement of the lubrication properties of grease with Mn₃O₄/graphene (Mn₃O₄#G) nanocomposite additive. Friction, 9(6), 1361-1377. Go to original source...
  39. RESTUCCIA, P., FERRARIO, M., RIGHI, M. C. (2020). Monitoring water and oxygen splitting at graphene edges and folds: Insights into the lubricity of graphitic materials. Carbon, 156, 93-103. Go to original source...
  40. ASM Handbook, ''Volume 4A Steel Heat Treating Fundamentals and Processes'', 2013.
  41. HALDAR, A., CHATTERJEE, S., KOTIA, A., KUMAR, N., GHOSH, S. K. (2020). Analysis of rheologi-cal properties of MWCNT/SiO2 hydraulic oil nanolubricants using regression and artificial neural network. International Communications in Heat and Mass Transfer, 116, 104723. Go to original source...
  42. ASTM International. (2004). ASTM G99-04: Standard test method for wear testing with a pin-on-disk appa-ratus.
  43. SHARUDDIN, M. H. BIN, SULAIMAN, M. H., KAMARUDDIN, S., DAHNEL, A. H., ABD HALIM, N. F. H., RIDZUAN, M. J. M., ABDUL-RANI, A. M. (2023). Properties and tribological evaluation of graphene and fullerene nanoparticles as additives in oil lubrication. Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 237(8), 1647-1656. Go to original source...
  44. KUMAR, N., SAINI, V., BIJWE, J. (2020). Tribological investigations of nano and micro-sized graphite particles as an additive in lithium-based grease. Tribology Letters, 68, 124. Go to original source...
  45. WANG, Y., LIU, Z., GAO, X., QIU, Q., WANG, M. (2024). Influence of Few-Layer Graphene on Frictional Properties of Lithium Compound Grease. Coatings, 14(5), 561. Go to original source...
  46. STEFAN-HENNINGSEN, E., ROBERTS, N., KIANI, A. (2025). Enhancing tribological performance: A comprehensive review of graphene-based additives in lubricating greases. Results in Engineering, 25, 104551. Go to original source...
  47. DONG, Y., MA, B., XIONG, C., LIU, Y., ZHAO, Q. (2023). Study on the Lubricating Characteristics of Graphene Lubricants. Lubricants, 11(12), 506. Go to original source...
  48. YEHIA, H. M., NOUH, F., EL-KADY, O. (2018). Effect of graphene nano-sheets content and sintering time on the microstructure, coefficient of thermal expansion, and mechanical properties of (Cu/WC-TiC-Co) nano-composites. Journal of Alloys and Compounds, 764, 36-43. Go to original source...
  49. ESSA, F. A., ELSHEIKH, A. H., YU, J., ELKADY, O. A., SALEH, B. (2021). Studies on the effect of applied load, sliding speed and temperature on the wear behavior of M50 steel reinforced with Al₂O₃ and/or graphene nanoparticles. Journal of Materials Research and Technology, 12, 283-303. Go to original source...
  50. CHAIYASON, T., PRASOMTHONG, S., THOSA, P., CHARONERAT, S., KEIDLAPHI, P. (2026). Hybrid ANN-GA Modeling and Experimental Optimization of GMAW-Based Additive Manufacturing of Aluminum 5083 for Enhanced Mechanical Properties. Manufacturing Technology Journal, 26(2), 133-147. Go to original source...
  51. BAJTO©OVÁ, L., MY©IÈKOVÁ, M., ©TAFFENOVÁ, N., CHOCHO¥AKOVÁ, E., HANU©, J., FIKAR, J., CIESLAR, M. (2025). In Situ TEM and Molecular Dynamics Investigation of Grain Growth in Nanocrystalline Cu Nanoparticles. Manufacturing Technology Journal, 25(5), 576-581. Go to original source...
  52. KNAST, P., PETRÙ, J., LEGUTKO, S., SOOS, L., POKUSOVA, M. (2025). SEM Analysis of Surface Layers with Variable Ra Parameters for Tribological Optimization in Design Engineering. Manufacturing Technology Journal, 25(2), 185-201. Go to original source...

This is an open access article distributed under the terms of the Attribution-NonCommercial 4.0 International License (CC BY-NC 4.0), which permits non-comercial use, distribution, and reproduction in any medium, provided the original publication is properly cited. No use, distribution or reproduction is permitted which does not comply with these terms.